Instruction/ maintenance manual of the product -CGT DCS
Go to page of 14
Dyn a mic Coo king S y s tem s, In c. The Professional Restaurant Gas Tandoor Use and Installation Guide Models: DCS-CGT.
1 A M e ss a ge T o Ou r C u st o m e r s FOR YOUR SAFETY Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any other appliance. If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flames.
2 In t roduction / S af ety P recaution s Thank you for choosing your new Dynamic Cooking Systems Professional Restaurant Gas Tandoor. Our prod- ucts are designed to be safe and reliable when properly cared for and used reasonably. Periodical inspections are recommended by your service agency or dealer.
3 Fe a t u re s The Professional T andoor by DCS comes with these standard features. ● Input rating = 70,0000 BTU/HR ● Overall dimensions 34 ” wide x 36 ” high x 35 ” deep. ● 1 inch thick ceramic bowl to retain heat longer and more evenly.
4 Sp e c i f ication s EXTERIOR DIMENSION ● WIDTH: 34 ” (864mm) ● HEIGHT (w/6 ” legs): 36 ” (915mm) ● DEPTH: 35 ” (889mm) SHIPPING WEIGHT DIMENSIONS ● MINIMUM ENTRY CLEARANCE: Crated 39 1/4 ” - Uncrated 34 1/4 ” GAS REQUIREMENTS ● MANIFOLD PRESSURE: 6 ” W.
5 Pr e-In s t a l l a t i o n Important: Safe and satisfactory operation of your equipment depends on its proper installation. Installation must conform to local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1-1988 (or latest edition).
UNP ACKING Check that the container is upright. Use outward prying no hammering to remove the carton. Check the Tandoor for visible damage. If such damage has occurred, do not refuse shipment, but contact the carrier and file the appropriate freight claims.
7 In s t a lling T he T andoo r PRESSURE REGULA TING The Tandoor and its individual shut-off valve must be disconnected from the gas supply piping system during any pressure testing of that system at pressures in excess of 1/2 psig.
8 In i t i a l St a r t-u p / Op e r a t i o n PLACEMENT OF LA V A ROCK Place a layer of lava rock on the stainless steel pan located directly above the burners. PILOT & MAIN BURNERS All Tandoors are tested and adjusted before leaving the factory, effectively matching them to sea level condi- tions.
9 Cleaning and Maintenance GENERAL New units are wiped clean at the factory to remove any visible signs of dirt, oil, grease remaining from the man- ufacturing process. They should be washed thoroughly with hot soapy water to remove any installation dust or debris before being used for food preparation.
10 Pa r t s L i s t ITEM DESCRIPTION PART NO. 1M anual Valve 3/8 13034 2 Knob Chrome 14020-02 3 Ceramic Bowl 14272 4 Logo DCS Medallion Series 17301 5 Leg Assembly 18036-1 6 Lid W/Assembly 20047 7 Lid.
11 T roub le s hooting These troubleshooting procedures must be carried out only by a factory authorized agency for warranty repair. The problems and possible solutions given below cover those most commonly encountered.
12 Wa r ranty For warranty service, contact your local DCS authorized service agency. Provide him with the Model Number, Serial Number, and date of installation, and a brief description of the problem.
Part No. 17331 Litho in USA 08/2000 As product improvement is an ongoing process at DCS, we reserve the right to change specifications or design without notice.
An important point after buying a device DCS -CGT (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought DCS -CGT yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data DCS -CGT - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, DCS -CGT you will learn all the available features of the product, as well as information on its operation. The information that you get DCS -CGT will certainly help you make a decision on the purchase.
If you already are a holder of DCS -CGT, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime DCS -CGT.
However, one of the most important roles played by the user manual is to help in solving problems with DCS -CGT. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device DCS -CGT along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
