Instruction/ maintenance manual of the product MOV230 Dacor
Go to page of 20
Installa tion Instr uc tion s Dis cove r y W al l O ven For use with models: EO, MO and PO Part No. 65433 Rev . F Preliminary - For Review Only No Scheduled Release Date.
All specifications are subject to change without notice. Dacor ® assumes no liability for changes to specifications. © 2007 Dacor , all rights reserved.
1 Planning the Installation ................................................... 6 Selecting the Location ...................................................... 6 Cabinet Cut-Out ............................................................... 6 Cabinet Cut-Out (continued) .
2 Impor tant Safety Instructions Read the accompanying use and care manual 1. before operating this appliance. Keep packaging materials away from children. 2. Plastic sheets and bags can cause suffocation. If you receive a damaged product, immediately 3.
3 Model Identification EO230xxx A = MODEL tYPE Epicure Oven = EO Millennia Oven (vert. trim) = MOV Millennia Oven (horiz. trim) = MOH Preference Oven = PO B = CONFIGURA tION Single Oven = 1 Double Ove.
4 Product Specifications Model Number K L M N P Q R S EO127 27” (686mm) 27 15/16” (710mm) 23 3/8” (594mm) 2 5/16” (59mm) 7 3/8” (187mm) 6 3/8” (162mm) 26 3/8” (670mm) 25 3/8” (644mm) P.
5 Product Specifications Single W all Oven Dimension Double W all Oven Dimension “R” “N” “P” “Q” “M” 1 1/16” (27mm) 66” (1676mm) Flexible Conduit “K” “L” 1 1/4” (32mm.
6 “C” 9 5/8” (244mm) Recommended (May be altered) 1 ¾“ (45mm) Clear to T op of Drawer for Heat Exhaust “B” “A” 4“ T ypical T oe Kick (Shown) Recommended Electrical Location 3/4” (.
7 1 ¾” (45mm) Min. to Combustible Floor “A” “B” “A” “B” 1 1/2” (38mm) T ypical Counter 4“ T ypical T oe Kick (Shown) Alternate Electrical Locations 3/4” (19mm) Support Platform 4“ (102mm) Min. Between Cutout 3/4” (19mm) Support Platform Recommended Electrical Location 1“ (25mm) Min.
8 Planning the Installation Cabinet Cut-Out (continued) Suppor t Platform W ARNING The top surface of the support platform must be installed flush with the cutout in the front of the cabinet or wall and any trim. Failure to install the platform properly may cause the exhaust vent to deform and/or become obstructed.
9 Planning the Installation Electrical Specifications IMPORt ANt Preheat times and cavity temperature recovery times • will be increased slightly if operating on less than a 240 V ac circuit. This appliance is provided with electrical connec- • tion leads in a flexible metal conduit.
10 Installation Instructions Before proceeding, turn off power to the circuit to which 1. the oven will be connected at the circuit breaker or fuse box. Position the oven directly in front of the cabinet cutout. 2. Feed the appliance conduit into the electrical junction 3.
11 Installation Instructions Connecting to a Three Wire Electrical System - Where Local Codes Per mit W ARNING Do not connect the green appliance conduit wire to the neutral (white) junction box wire unless local building codes permit. Separate the wires coming out of the appliance conduit.
12 Installation Instructions Final Installation W ARNING A minimum of two people are required to safely • install this appliance. Do not attempt to disengage the hinge catches with • the door removed from the oven. The hinge springs could release, causing personal injury .
13 Raise the door so that it is at a 15° angle from the front 3. of the oven. Hold the door with one hand on each side. Lift the door up and out. Install the Oven in the Cabinet W ARNING Use an appliance dolly to move the appliance when • installing it or removing it from the wall for service.
14 Grasp the oven door on opposite sides and hold it at a 1. 15° angle from the front of the oven. See facing page. Slide the hinges into the hinge openings, resting the 2. bottom of the hinge arms on the hinge receptacles. Continue to hold the door at a 15° angle with one hand 3.
15 Installation Instructions Door Installation Installation Checklist W ARNING T o ensure a safe and proper installation, the follow- • ing checklist should be completed by the installer to ensure that no part of the installation has been overlooked.
16 Notes.
.
Dacor ● 1440 Bridge Gate Drive, Diamond Bar , CA 91765 ● T el: (800) 793-0093 ● F AX: (626) 403-3130 ● www .Dacor.com.
An important point after buying a device Dacor MOV230 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Dacor MOV230 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Dacor MOV230 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Dacor MOV230 you will learn all the available features of the product, as well as information on its operation. The information that you get Dacor MOV230 will certainly help you make a decision on the purchase.
If you already are a holder of Dacor MOV230, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Dacor MOV230.
However, one of the most important roles played by the user manual is to help in solving problems with Dacor MOV230. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Dacor MOV230 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
