Instruction/ maintenance manual of the product Contour Electrol Da-Lite
Go to page of 8
DA-LITE SCREEN COMP ANY , INC. 3100 North Detroit Street Post Office Box 137 Warsaw , Indiana 46581-0137 Phone: 574-267-8101 800-622-3737 Fax: 574-267-7804 T oll Free Fax: 877-325-4832 www .da-lite.com e-mail: info@da-lite.com Instruc tion Book for C ONT OUR ® ELEC TROL® T he Da-Lit e Diff er enc e .
1 IMPORT ANT SAFETY INSTRUCTIONS When using your video equipment, basic safety precautions should always be followed, including the following: 1. Read and understand all instructions before using. 2. Position the cord so that it will not be tripped over , pulled, or contact hot surfaces.
2 Carefully unpack screen and remove outer wrapping from case. Remove the black tape and rubber bands from the slat bar after the case has been installed. There are three ways to install the Contour ® Electrol ® : Wall Mount, Ceiling Mount, or Ceiling Hook.
3 ELECTRICAL INST ALLA TION Internal wiring has been completed at the factory . Installer must route power to the wall switch and to the junction box located on the left end of the screen case. Standard installation is for a single 120V AC or 240V AC wall switch to control the screen.
4 SCREEN AdjUSTMENT FOR 220v/240v SCREENS WITH A BUIL T -IN LOW vOL T AGE CONTROL 1. Remove the cover plate from the 3-button wall switch and remove the switch from the junction box. 2. Locate small 3-position switch on back of wall switch. (See Figure 11) CAUTION: Do not adjust for more drop than what was ordered.
5 CONTOUR ® ELECTROL ® INST ALLA TION UP OFF DOWN THIS SWITCH CAN NOT BE USED WITH L VC. 120V WIRING DIAGRAM FOR ST ANDARD WALL SWITCH 240V WIRING DIAGRAM WITH OPTIONAL BUIL T -IN VIDEO PROJECTOR IN.
6 CONTOUR ® ELECTROL ® INST ALLA TION FIGURE 11 LOW-VOL TAGE W ALL SWITCH OPTIONAL IR AND RF REMOTE CONTROL MOTOR BLUE (COMMON) BROWN (HOT) GREEN GROUND TO CASE 240VAC 50HZ 240V WIRING DIAGRAM WITH .
Printed in U.S.A. 88819 Rev. 9/11 TROUBLESHOOTING SYMPTOM 1. Screen will not operate. Motor does not hum. 2. Incorrect stopping position in downward direction. 3. Incorrect stopping position in upward direction. 4. Noise. NOTE: Screen will operate with a low pitched hum.
An important point after buying a device Da-Lite Contour Electrol (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Da-Lite Contour Electrol yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Da-Lite Contour Electrol - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Da-Lite Contour Electrol you will learn all the available features of the product, as well as information on its operation. The information that you get Da-Lite Contour Electrol will certainly help you make a decision on the purchase.
If you already are a holder of Da-Lite Contour Electrol, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Da-Lite Contour Electrol.
However, one of the most important roles played by the user manual is to help in solving problems with Da-Lite Contour Electrol. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Da-Lite Contour Electrol along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
