EN
D-Link logo
Official user manual

D-Link Version 1.01

66 pages·4.4 MB·Home Security System·PDF·ENDEFRITNLJA
D-Link Version 1.01
Table of Contents 51 sections Product Overview · Package Contents · Introduction · System Requirements · … ShowHide
Page 1 of the D-Link Version 1.01 user manual — DCS-2330L
Page 1 · click to enlarge
Page 1

Version 1.01 | 04/22/2014

D-Link Version 1.01 diagram (page 1)
Fig. 1

User Manual

HD Wireless Outdoor Cloud Camera

DCS-2330L

Page 2 of the D-Link Version 1.01 user manual — Trademarks
Page 2 · click to enlarge
Page 2

Preface

D-Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes. Information in this document may become obsolete as our services and websites develop and change. Please refer to the www.mydlink.com website for the most current information.

Manual Revisions

RevisionDateDescription 1.00December 12, 2013DCS-2330L Revision A1 with firmware version 1.00 1.01April 22, 2014DCS-2330L Revision A1 with firmware version 1.01

Trademarks

D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or its subsidiaries in the United States or other countries. All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies.

Copyright © 2014 D-Link Corporation.

All rights reserved. This publication may not be reproduced, in whole or in part, without prior expressed written permission from D-Link Corporation.

Page 4 of the D-Link Version 1.01 user manual — Product Overview
Page 4 · click to enlarge
Page 4
Section 1Product Overview

Product Overview

Package Contents

DCS-2330L HD Wireless Outdoor Cloud Camera

CD-ROM with User Manual and software

If any of the above items are missing, please contact your reseller.

CAT5 Ethernet cable · Power adapter (Pre-Attached) · Quick Installation Guide

Page 5 of the D-Link Version 1.01 user manual — System Requirements
Page 5 · click to enlarge
Page 5
Section 1Product Overview

Introduction

Congratulations on your purchase of the DCS-2330L HD Wireless Outdoor Cloud Camera. The DCS-2330L is a versatile and unique solution for your small office or home. Unlike a standard webcam, the DCS-2330L is a complete system with a built-in CPU and web server that transmits high quality video images for security and outdoor surveillance. The DCS-2330L can be accessed remotely, and controlled from any PC/Notebook over your local network or through the Internet via a web browser. The simple installation and intuitive web-based interface offer easy integration with your Ethernet/Fast Ethernet or 802.11n/g wireless network. The DCS-2330L also comes with remote monitoring and motion detection features for a complete and cost- effective home security solution.

System Requirements

  • Computer with Microsoft Windows ® 8/7/Vista/XP, or Mac with OS X 10.6 or higher
  • PC with 1.3GHz or above and at least 128MB RAM
  • Internet Explorer 7, Firefox 12, Safari 4, or Chrome 20 or higher version with Java installed and enabled
  • Existing 10/100 Ethernet-based network or 802.11g/n wireless network
Page 6 of the D-Link Version 1.01 user manual — Features
Page 6 · click to enlarge
Page 6
Section 1Product Overview

Features

Simple to Use The DCS-2330L is a stand-alone system with a built-in CPU, requiring no special hardware or software. The DCS-2330L supports both ActiveX mode for Internet Explorer and Java mode for other browsers such as Firefox® and Safari®.

Supports a Variety of Platforms Supporting TCP/IP networking, HTTP, and other Internet related protocols. The DCS-2330L can also be integrated easily into other Internet/Intranet applications because of its standards-based features.

Web Configuration Using a standard Web browser, administrators can configure and manage the Network Camera directly from its own Web page via Intranet or Internet. This means you can access your DCS-2330L anytime, anywhere in the world.

Broad Range of Applications With today’s high-speed Internet services, the Network Camera can provide the ideal solution for delivering live video images over the Intranet and Internet for remote monitoring. The Network Camera allows remote access using a Web browser for live image viewing, and allows the administrator to manage and control the Network Camera anytime, anywhere in the world. Many applications exist, including industrial and public monitoring of homes, offices, banks, hospitals, child-care centers, and amusement parks.

Remote Monitoring Utility The D-ViewCam application adds enhanced features and functionality for the Network Camera and allows administrators to configure and access the Network Camera from a remote site via Intranet or Internet. Other features include image monitoring, recording images to a hard drive, viewing up to 32 cameras on one screen, and taking snapshots.

IR LED for Day and Night Functionality The built-in infrared LEDs enables night time viewing of up to 16 feet (5 meters).

IP65 Weatherproof Housing The DCS-2330L uses an IP65 weatherproof housing, allowing you to rest assured that in the toughest of conditions, it will continue to provide round-the-clock surveillance.

802.11n Wireless or Ethernet/Fast Ethernet Support The DCS-2330L offers wireless 802.11n and Ethernet/Fast Ethernet connectivity, making the DCS-2330L easy to integrate into your existing network environment. The DCS-2330L works with a 10Mbps Ethernet based network or 100Mbps Fast Ethernet based network for traditional wired environments, and works with 802.11n routers or access points for added flexibility. The Site Survey feature also allows you to view and connect to any available wireless networks.

Page 7 of the D-Link Version 1.01 user manual — Front Hardware Overview
Page 7 · click to enlarge
Page 7
Section 1Product Overview

Front Hardware Overview

D-Link Version 1.01 — Front Hardware Overview diagram (page 7)
Fig. 2 · Front Hardware Overview
1Camera LensRecords video of the surrounding area 2Light SensorThe light sensor measures the lighting conditions and switches between color and infrared accordingly 3MicrophoneRecords audio from the surrounding area 4PIRPassive Infrared sensor for motion detection 5IR LEDInfrared LED illuminates the camera's field of view at night 6WPS Status LEDIndicates the WPS connection status of the camera 7Power/Status LEDIndicates the camera's current status 8AntennaOutdoor wireless antenna
Page 8 of the D-Link Version 1.01 user manual — Rear: External
Page 8 · click to enlarge
Page 8
Section 1Product Overview

Rear: External

D-Link Version 1.01 — Rear: External diagram (page 8)
Fig. 3 · Rear: External
1Weatherproof CoverWeatherproof protective panel 2Protective Cable CoverWeatherproof cable connection cover 3Weatherproof CoverWeatherproof cover for the MicroSD Card slot and reset button 4Weatherproof Screw CoveringWeatherproof protective covering for enclosure screws 5Power Cable ReceptacleConnects to the included DC 5 V power adapter 6WPS ButtonPress this button, then press the WPS button for 5 seconds on your router to set up a wireless connection automatically 7Adjustment RingTighten or loosen the adjustment ring to adjust the camera's position
Page 9 of the D-Link Version 1.01 user manual — Rear: Internal
Page 9 · click to enlarge
Page 9
Section 1Product Overview

Rear: Internal

D-Link Version 1.01 — Rear: Internal diagram (page 9)
Fig. 4 · Rear: Internal
D-Link Version 1.01 — Rear: Internal diagram (page 9)
Fig. 5 · Rear: Internal
1DC Power ConnectorConnected to the included DC 5 V power adapter 2RJ45 Ethernet PortRJ45 connector for Ethernet 3Reset ButtonUse a paperclip or similar tool to press and hold the recessed button for 10 seconds to reset the camera 4SD Memory Card SlotInsert a MicroSD card for for storing recorded images and video
Page 10 of the D-Link Version 1.01 user manual — Removing the Top Panel
Page 10 · click to enlarge
Page 10
Section 1Product Overview

Removing the Top Panel

D-Link Version 1.01 — Removing the Top Panel diagram (page 10)
Fig. 6 · Removing the Top Panel
1. Place the camera face down on a non-slip flat surface.
2. Carefully pry out the two protective rubber screw coverings using a thin flat blade.
3. Undo the two screws using a Philips #00 Screwdriver.
4. Lift off the protective panel.
Page 11 of the D-Link Version 1.01 user manual — Replacing the Ethernet Cable
Page 11 · click to enlarge
Page 11
Section 1Product Overview

Replacing the Ethernet Cable

D-Link Version 1.01 — Replacing the Ethernet Cable diagram (page 11)
Fig. 7 · Replacing the Ethernet Cable
1. Follow the steps outlined in "Removing the Top Panel" on page 10.
2. Unplug the Ethernet cable from the RJ45 connector.
3. Carefully remove the weatherproof cable connection cover.
4. Attach the weatherproof cable connection cover to the new Ethernet cable.
5. Plug the new Ethernet cable into the RJ45 connector.
6. Follow the steps outlined in "Reattaching the Top Panel" on page 12.
Page 12 of the D-Link Version 1.01 user manual — Reattaching the Top Panel
Page 12 · click to enlarge
Page 12
Section 1Product Overview

Reattaching the Top Panel

D-Link Version 1.01 — Reattaching the Top Panel diagram (page 12)
Fig. 8 · Reattaching the Top Panel
1. Seat the protective panel, ensuring a tight fit with the inlaid rubber seal.
2. Replace the two screws. Ensure that the screws are tightened firmly.
3. Firmly replace the protective rubber screw coverings.
Page 13 of the D-Link Version 1.01 user manual — Using the Reset Button
Page 13 · click to enlarge
Page 13
Section 1Product Overview

Removing the Bottom Panel

1. Place the camera face down on a non-slip flat surface.
D-Link Version 1.01 — Removing the Bottom Panel diagram (page 13)
Fig. 9 · Removing the Bottom Panel
2. Carefully pry out the two protective rubber screw coverings using a thin flat blade.
3. Undo the two screws using a Philips #00 Screwdriver.
4. Lift off the protective panel.

If you need to install an SD Memory Card please skip to "Installing an SD Memory Card" on page 14.

Using the Reset Button

If you need to use the Reset Button follow these steps.

1. Follow the steps outlined in "Removing the Bottom Panel" on page 13.
D-Link Version 1.01 — Using the Reset Button diagram (page 13)
Fig. 10 · Using the Reset Button
2. Using a paperclip or similar tool, press and hold the Reset Button for 10 seconds. This will reset the device to it's factory settings.
3. Follow the steps outlined in "Reattaching the Bottom Panel" on page 14.
Page 14 of the D-Link Version 1.01 user manual — Reattaching the Bottom Panel
Page 14 · click to enlarge
Page 14
Section 1Product Overview

Installing an SD Memory Card

1. Follow the steps outlined in "Removing the Bottom Panel" on page 13.
D-Link Version 1.01 — Installing an SD Memory Card diagram (page 14)
Fig. 11 · Installing an SD Memory Card
2. Insert a MicroSD Memory card into the slot, with the notch facing right.
3. Follow the steps outlined in "Reattaching the Bottom Panel" on page 14.

Reattaching the Bottom Panel

1. Seat the protective panel, ensuring a tight fit with the inlaid rubber seal.
D-Link Version 1.01 — Reattaching the Bottom Panel diagram (page 14)
Fig. 12 · Reattaching the Bottom Panel
2. Replace the two screws. Ensure that the screws are tightened firmly.
3. Firmly replace the protective rubber screw coverings.
Page 15 of the D-Link Version 1.01 user manual — To create a WPS connection:
Page 15 · click to enlarge
Page 15
Section 1Product Overview

Optional: WPS Wireless Connection Alternatively, if your router supports WPS, you can use the WPS button on the camera to easily create a secure wireless connection to your network.

D-Link Version 1.01 — Installing an SD Memory Card diagram (page 15)
Fig. 13 · Installing an SD Memory Card

To create a WPS connection:

Step 1 Press and hold the WPS button for approximately 5-6 seconds. The blue WPS status LED on the front panel will blink.

Step 2 Within 60 seconds press the WPS button on your router. On some routers, you may need to log in to the web interface and click on an on-screen button to activate the WPS feature. If you are not sure where the WPS button is on your router, please refer to your router’s User Manual.

The DCS-2330L will automatically create a wireless connection to your router. While connecting, the status LED will flash. When the connection process is complete, the status LED will turn solid.

WPS Button

Page 16 of the D-Link Version 1.01 user manual — Installation Zero Configuration Setup
Page 16 · click to enlarge
Page 16
Section 2Installation

Installation Zero Configuration Setup

If you have a mydlink-enabled Cloud Router, you can take advantage of Zero Configuration. Zero Configuration automatically configures your camera's settings for you, and adds it to your mydlink account automatically. This type of setup allows you to set up your camera by simply plugging it in and connecting it to your router.

Connect your camera to your mydlink-enabled Cloud Router and Zero Configuration will automatically configure your DCS-2330L and automatically add the camera to your mydlink account. After the short time it takes to do this you can remotely access your camera from the www.mydlink.com website to manage and monitor your DCS-2330L.

Connect the Ethernet Cable Carefully remove the rubber seal on the back of the DCS-2330L and use the included Ethernet cable to connect the DCS-2330L to your network.

D-Link Version 1.01 — Installation Zero Configuration Setup diagram (page 16)
Fig. 14 · Installation Zero Configuration Setup

Attach the External Power Supply Attach the external power supply to your wall outlet or power strip.

D-Link Version 1.01 — Installation Zero Configuration Setup diagram (page 16)
Fig. 15 · Installation Zero Configuration Setup
D-Link Version 1.01 — Installation Zero Configuration Setup diagram (page 16)
Fig. 16 · Installation Zero Configuration Setup
Page 17 of the D-Link Version 1.01 user manual — DCS-2330L
Page 17 · click to enlarge
Page 17
Section 2Installation

Check Your mydlink Account Open a web browser and login to your mydlink account. The mydlink page will check for new devices and display a New device Found! pop-up notification in the bottom-left corner. Click the notification to continue.

D-Link Version 1.01 — Installation diagram (page 17)
Fig. 17 · Installation

A summary and confirmation notification will appear with the automatically configured details. Make a note of the details and click Yes to add the camera to your account.

D-Link Version 1.01 — Installation diagram (page 17)
Fig. 18 · Installation

DCS-2330L

Page 18 of the D-Link Version 1.01 user manual — DCS-2330L
Page 18 · click to enlarge
Page 18
Section 2Installation

Zero Configuration will navigate to the mydlink Live View tab for your camera where you will see a screen similar to the following.

D-Link Version 1.01 — Installation diagram (page 18)
Fig. 19 · Installation

DCS-2330L

If you wish to connect your camera to your router wirelessly, you can simply disconnect the Ethernet cable and move the camera to its intended location; your router's wireless settings have been automatically transferred to the camera, and no further configuration is required.

D-Link Version 1.01 — DCS-2330L diagram (page 18)
Fig. 20

Your camera is now set up, and you can skip to "mydlink" on page 22 to learn more about the mydlink features of this camera, or to "Configuration" on page 23 for advanced configuration of your camera.

Page 19 of the D-Link Version 1.01 user manual — Camera Installation Wizard
Page 19 · click to enlarge
Page 19
Section 2Installation

Camera Installation Wizard

Windows Users

Insert the Installation CD-ROM into your computer’s optical drive to start the autorun program.

Simply click Set up your Cloud Camera to go through the Setup Wizard, which will guide you step-by-step through the installation process from connecting your hardware to configuring your camera and registering it with your mydlink account.

D-Link Version 1.01 — Camera Installation Wizard diagram (page 19)
Fig. 21 · Camera Installation Wizard
Page 20 of the D-Link Version 1.01 user manual — Mac Users
Page 20 · click to enlarge
Page 20
Section 2Installation

Mac Users

Insert the Installation CD-ROM into your computer’s CD drive. On the desktop, open your CD drive and double-click on the SetupWizard file.

Within 20-30 seconds, the Setup Wizard will open, which will guide you step-by-step through the installation process from connecting your hardware to configuring your camera and registering it with your mydlink account.

SetupWizard

Page 21 of the D-Link Version 1.01 user manual — Manual Hardware Installation
Page 21 · click to enlarge
Page 21
Section 2Installation

Manual Hardware Installation

If you wish to set up your camera without using the Camera Setup Wizard, please follow these steps.

Connect the Ethernet Cable Carefully remove the rubber seal on the back of the DCS-2330L and use the included Ethernet cable to connect the DCS-2330L to your network.

D-Link Version 1.01 — Manual Hardware Installation diagram (page 21)
Fig. 22 · Manual Hardware Installation
D-Link Version 1.01 — Manual Hardware Installation diagram (page 21)
Fig. 23 · Manual Hardware Installation

Attach the External Power Supply Attach the external power supply to your wall outlet or power strip.

Page 22 of the D-Link Version 1.01 user manual — DCS-2330L
Page 22 · click to enlarge
Page 22
Section 2Installation

mydlink

After registering your DCS-2330L camera with a mydlink account in the Camera Installation Wizard, you will be able to remotely access your camera from the www.mydlink.com website. After signing in to your mydlink account, you will see a screen similar to the following:

D-Link Version 1.01 — mydlink diagram (page 22)
Fig. 24 · mydlink

DCS-2330L

D-Link Version 1.01 — DCS-2330L diagram (page 22)
Fig. 25

For more details on using your camera with mydlink, go to the Support section of the mydlink website and check the User Manual section for your product to find the latest instruction guide for your camera's mydlink features.

Page 23 of the D-Link Version 1.01 user manual — Configuration Using the Configuration Interface
Page 23 · click to enlarge
Page 23

Configuration Using the Configuration Interface

After completing the Camera Installation Wizard, you are ready to use your camera. The camera’s built-in Web configuration utility is designed to allow you to easily access and configure your DCS-2330L. At the end of the wizard, enter the IP address of your camera into a web browser, such as Mozilla Firefox. To log in, use the User name admin and the password you created in the Installation Wizard. If you did not create a password, the default password is blank. After entering your password, click OK.

D-Link Version 1.01 — Configuration Using the Configuration Interface diagram (page 23)
Fig. 26 · Configuration Using the Configuration Interface
Page 24 of the D-Link Version 1.01 user manual — Live Video
Page 24 · click to enlarge
Page 24

Live Video

This section shows your camera’s live video. You may select any of the available icons listed below to operate the camera. You may also select your language using the drop-down menu on the left side of the screen.

You can zoom in and out on the live video image using your mouse. Right-click to zoom out or left-click to zoom in on the image.

SD Status:

This option displays the status of the SD card. If no SD card has been inserted, this screen will display the message "Card Invalid."

D-Link Version 1.01 — Live Video diagram (page 24)
Fig. 27 · Live Video

This indicator will change color when a trigger event occurs.

D-Link Version 1.01 — Live Video diagram (page 24)
Fig. 28 · Live Video

When a recording is in progress, this indicator will change color.

This control pad can be used to electronically pan, tilt, and zoom (ePTZ) within the camera's predefined view area, if one has been defined.

Auto Pan Starts the automatic panning function. The ROI will pan from back and forth within the FOV

Stop Stops the camera ePTZ motion

Preset Path Starts the camera's motion along the predefined path

You may select a value between 0 and 64. 0 is the slowest and 64 is the fastest. ePTZ Speed:

Motion Trigger Indicator · Recording Indicator · Control Pad

Page 25 of the D-Link Version 1.01 user manual — Live Video
Page 25 · click to enlarge
Page 25

Global View:

This window indicates the total field of view (FOV) of the camera. The red box indicates the visible region of interest (ROI).

Language:

You may select the interface language using this menu.

Go To(Preset List)

If any presets have been defined, selecting a preset from this list will display it.

Record a Video Clip

Set a Storage Folder

Listen/Stop Audio In (from

Show 6 more labels / short text on this page
Video Profile 1 · Video Profile 2 · Video Profile 3 · Full screen mode · microphone) · Take a Snapshot
Page 26 of the D-Link Version 1.01 user manual — Setup Setup Wizard
Page 26 · click to enlarge
Page 26

Setup Setup Wizard

To configure your Network Camera, click Internet Connection Setup Wizard. Alternatively, you may click Manual Internet Connection Setup to manually configure your Network Camera and skip to "Network Setup" on page 32.

D-Link Version 1.01 — Setup Setup Wizard diagram (page 26)
Fig. 29 · Setup Setup Wizard

To quickly configure your Network Camera’s motion detection settings, click Motion Detection Setup Wizard. If you want to enter your settings without running the wizard, click Manual Motion Detection Setup and skip to "Motion Detection" on page 43.

Page 27 of the D-Link Version 1.01 user manual — Internet Connection Setup Wizard
Page 27 · click to enlarge
Page 27

Internet Connection Setup Wizard

This wizard will guide you through a step-by-step process to configure your new D-Link Camera and connect the camera to the internet. Click Next to continue.

D-Link Version 1.01 — Internet Connection Setup Wizard diagram (page 27)
Fig. 30 · Internet Connection Setup Wizard
D-Link Version 1.01 — Internet Connection Setup Wizard diagram (page 27)
Fig. 31 · Internet Connection Setup Wizard

Click Next to continue.

Page 28 of the D-Link Version 1.01 user manual — DCS-2330L
Page 28 · click to enlarge
Page 28

Select Static IP if your Internet Service Provider has provided you with connection settings, or if you wish to set a static address within your home network. Enter the correct configuration information and click Next to continue.

If you are using PPPoE, select Enable PPPoE and enter your user name and password, otherwise click Next to continue.

If you have a Dynamic DNS account and would like the camera to update your IP address automatically, Select Enable DDNS and enter your host information. Click Next to continue.

D-Link Version 1.01 — Setup diagram (page 28)
Fig. 32 · Setup

Enter a name for your camera and click Next to continue.

D-Link Version 1.01 — Setup diagram (page 28)
Fig. 33 · Setup

DCS-2330L

Page 29 of the D-Link Version 1.01 user manual — DCS-2330L
Page 29 · click to enlarge
Page 29

Configure the correct time to ensure that all events will be triggered as scheduled. Click Next to continue.

D-Link Version 1.01 — Setup diagram (page 29)
Fig. 34 · Setup

If you have selected DHCP, you will see a summary of your settings, including the camera's IP address. Please write down all of this information as you will need it in order to access your camera.

D-Link Version 1.01 — Setup diagram (page 29)
Fig. 35 · Setup

Click Apply to save your settings.

DCS-2330L

Page 30 of the D-Link Version 1.01 user manual — Motion Detection Setup Wizard
Page 30 · click to enlarge
Page 30

Motion Detection Setup Wizard

This wizard will guide you through a step-by-step process to configure your camera's motion detection functions.

D-Link Version 1.01 — Motion Detection Setup Wizard diagram (page 30)
Fig. 36 · Motion Detection Setup Wizard

Click Next to continue.

D-Link Version 1.01 — Motion Detection Setup Wizard diagram (page 30)
Fig. 37 · Motion Detection Setup Wizard

This step will allow you to enable or disable motion detection, specify the detection sensitivity, and adjust the camera’s ability to detect movement.

You may specify whether the camera should capture a snapshot or a video clip when motion is detected.

Please see "Motion Detection" on page 43 for information about how to configure motion detection.

D-Link Version 1.01 — Motion Detection Setup Wizard diagram (page 30)
Fig. 38 · Motion Detection Setup Wizard

This step allows you to enable motion detection based on a customized schedule. Specify the day and hours. You may also choose to always record motion.

Step 1 · Step 2

Page 31 of the D-Link Version 1.01 user manual — Setup
Page 31 · click to enlarge
Page 31
D-Link Version 1.01 — Setup diagram (page 31)
Fig. 39 · Setup

This step allows you to specify how you will receive event notifications from your camera. You may choose not to receive notifications, or to receive notifications via e-mail or FTP.

Please enter the relevant information for your e-mail or FTP account.

Click Next to continue.

D-Link Version 1.01 — Setup diagram (page 31)
Fig. 40 · Setup

You have completed the Motion Detection Wizard.

Please verify your settings and click Apply to save them.

Please wait a few moments while the camera saves your settings and restarts.

D-Link Version 1.01 — Setup diagram (page 31)
Fig. 41 · Setup

Step 3 · Step 4

Page 32 of the D-Link Version 1.01 user manual — DHCP:
Page 32 · click to enlarge
Page 32

Network Setup

Use this section to configure the network connections for your camera. All relevant information must be entered accurately. After making any changes, click the Save Settings button to save your changes.

LAN Settings:

This section lets you configure settings for your local area network.

D-Link Version 1.01 — Network Setup diagram (page 32)
Fig. 42 · Network Setup

DHCP:

Select this connection if you have a DHCP server running on your network and would like your camera to obtain an IP address automatically.

If you choose DHCP, you do not need to fill out the IP address settings.

Static IP Address:

You may obtain a static or fixed IP address and other network information from your network administrator for your camera. A static IP address may simplify access to your camera in the future.

IP Address:

Enter the fixed IP address in this field.

Subnet Mask:

This number is used to determine if the destination is in the same subnet. The default value is 255.255.255.0.

Default router:

The gateway used to forward frames to destinations in a different subnet. Invalid gateway settings may cause the failure of transmissions to a different subnet.

Primary DNS:

The primary domain name server translates names to IP addresses.

Secondary DNS:

The secondary DNS acts as a backup to the primary DNS.

Enable UPnP Presentation:

Enabling this setting allows your camera to be configured as a UPnP device on your network.

Page 33 of the D-Link Version 1.01 user manual — Network Setup
Page 33 · click to enlarge
Page 33

Enabling this setting allows the camera to add port forwarding entries into the router automatically on a UPnP capable network.

D-Link Version 1.01 — Network Setup diagram (page 33)
Fig. 43 · Network Setup

Forwarding:

Enable PPPoE:

Enable this setting if your network uses PPPoE.

Enter the username and password for your PPPoE account. Re-enter your password in the Confirm Password field. You may obtain this information from your ISP.

Password:

HTTP Port:

The default port number is 80.

The default name is video#.mjpg, where # is the number of the stream.

Stream 1~3:

HTTPS Port:

You may use a PC with a secure browser to connect to the HTTPS port of the camera. The default port number is 443.

Authentication:

Depending on your network security requirements, the Network Camera provides three types of security settings for streaming via RTSP protocol: disable and digest. If digest authentication is selected, user credentials are encrypted using MD5 algorithm, thus providing better protection against unauthorized access.

RTSP Port:

The port number that you use for RTSP streaming to mobile devices, such as mobile phones or PDAs. The default port number is 554. You may specify the address of a particular stream. For instance, live1.sdp can be accessed at rtsp://x.x.x.x/video1.sdp where the x.x.x.x represents the ip address of your camera.

Enable UPnP Port · User Name / · Access Name for

Page 34 of the D-Link Version 1.01 user manual — MULTICAST
Page 34 · click to enlarge
Page 34

This Network Camera supports multiple streams simultaneously. The access name is used to differentiate the streaming source (video profile).

D-Link Version 1.01 — Network Setup diagram (page 34)
Fig. 44 · Network Setup

stream 1 ~ 3:

COS SETTING:

Enabling the Class of Service setting implements a best-effort policy without making any bandwidth reservations.

QOS SETTING:

Enabling QoS allows you to specify a traffic priority policy to ensure a consistent Quality of Service during busy periods. If the Network Camera is connected to a router that itself implements QoS, the router's settings will override the QoS settings of the camera.

IPv6:

Enable the IPv6 setting to use the IPv6 protocol. Enabling the option allows you to manually set up the address, specify an optional IP address, specify an optional router and an optional primary DNS.

MULTICAST

The DCS-2330L allows you to multicast each of the available streams via group address and specify the TTL value for each stream. Enter the port and TTL settings you wish to use if you do not want to use the defaults.

Access name for

Page 35 of the D-Link Version 1.01 user manual — SSID:
Page 35 · click to enlarge
Page 35

Wireless Setup

This section allows you to set up and configure the wireless settings on your camera. After making any changes, click the Save Settings button to save your changes.

Site Survey:

Click the Rescan button to scan for available wireless networks. After scanning, you can use the drop-down box to select an available wireless network. The related information (SSID, Wireless Mode, Channel, Authentication, Encryption) will be automatically filled in for you.

D-Link Version 1.01 — Wireless Setup diagram (page 35)
Fig. 45 · Wireless Setup

SSID:

Enter the SSID of the wireless access point you wish to use.

Wireless Mode:

Use the drop-down box to select the mode of the wireless network you wish to connect to. Infrastructure is normally used to connect to an access point or router. Ad-Hoc is usually used to connect directly to another computer.

Channel:

If you are using Ad Hoc mode, select the channel of the wireless network you wish to connect to, or select Auto.

Authentication:

Select the authentication you use on your wireless network - Open, Shared, WPA-PSK, or WPA2-PSK.

Encryption:

If you use WPA-PSK or WPA2-PSK authentication, you will need to specify whether your wireless network uses TKIP or AES encryption. If you use Open or Shared authentication, WEP encryption should be the setting.

Key:

If you use WEP, WPA-PSK, or WPA2-PSK authentication, enter the Key (also known as password) used for your wireless network.

Page 36 of the D-Link Version 1.01 user manual — Dynamic DNS
Page 36 · click to enlarge
Page 36

Dynamic DNS

DDNS (Dynamic Domain Name Server) will hold a DNS host name and synchronize the public IP address of the modem when it has been modified. A user name and password are required when using the DDNS service. After making any changes, click the Save Settings button to save your changes.

Enable DDNS:

Select this checkbox to enable the DDNS function.

D-Link Version 1.01 — Dynamic DNS diagram (page 36)
Fig. 46 · Dynamic DNS

Server Address:

Select your Dynamic DNS provider from the pull down menu or enter the server address manually.

Host Name:

Enter the host name of the DDNS server.

User Name:

Enter the user name or e-mail used to connect to your DDNS account.

Password:

Enter the password used to connect to your DDNS server account.

Timeout:

Enter the DNS timeout values you wish to use.

Status:

Indicates the connection status, which is automatically determined by the system.

Page 37 of the D-Link Version 1.01 user manual — Image Setup
Page 37 · click to enlarge
Page 37

Image Setup

In this section, you may configure the video image settings for your camera. A preview of the image will be shown in Live Video.

The Privacy Mask setting allows you to specify up to 3 rectangular areas on the camera's image to be blocked/excluded from recordings and snapshots.

D-Link Version 1.01 — Image Setup diagram (page 37)
Fig. 47 · Image Setup

Mask:

You may click and drag the mouse cursor over the camera image to draw a mask area. Right clicking on the camera image brings up the following menu options:

D-Link Version 1.01 — Image Setup diagram (page 37)
Fig. 48 · Image Setup

Disable All: Disables all mask areas Enable All: Enables all mask areas Reset All: Clears all mask areas.

Anti Flicker:

If the video flickers, try enabling this setting.

Mirror:

This will mirror the image horizontally.

Flip:

This will flip the image vertically. When turning Flip on, you may want to consider turning Mirror on as well.

Power Line:

Select the frequency used by your power lines to avoid interference or distortion.

White Balance:

Use the drop-down box to change white balance settings to help balance colors for different environments. You can choose from Auto, Outdoor, Indoor, Fluorescent, and Push Hold.

Enable Privacy

Page 38 of the D-Link Version 1.01 user manual — Image Setup
Page 38 · click to enlarge
Page 38

Exposure Mode:

Changes the exposure mode. Use the drop-down box to set the camera for Indoor, Outdoor, or Night environments, or to Moving to capture moving objects. The Low Noise option will focus on creating a high-quality picture without noise. You can also create 3 different custom exposure modes. The Max Gain setting will allow you to control the maximum amount of gain to apply to brighten the picture.

Denoise:

This setting controls the amount of noise reduction that will be applied to the picture.

Brightness:

Adjust this setting to compensate for backlit subjects.

Contrast:

Adjust this setting to alter the color intensity/ strength.

Saturation:

This setting controls the amount of coloration, from grayscale to fully saturated.

Sharpness:

Specify a value from 0 to 8 to specify how much sharpening to apply to the image.

Reset Default:

Click this button to reset the image to factory default settings.

Page 39 of the D-Link Version 1.01 user manual — Audio and Video
Page 39 · click to enlarge
Page 39

Audio and Video

You may configure up to 3 video profiles with different settings for your camera. Hence, you may set up different profiles for your computer and mobile display. In addition, you may also configure the two-way audio settings for your camera. After making any changes, click the Save Settings button to save your changes.

Aspect ratio:

Set the aspect ratio of the video to 4:3 standard or 16:9 widescreen.

D-Link Version 1.01 — Audio and Video diagram (page 39)
Fig. 49 · Audio and Video

Mode:

Set the video codec to be used to JPEG, or H.264.

Frame size determines the total capture resolution, and View window area determines the Live Video viewing window size. If the Frame size is larger than the Live Video size, you can use the ePTZ controls to look around.

Frame size / View

window area:

16:9 1280 x 720, 800 x 448, 640 x 360, 480 x 272, 320 x 176

4:3 960x720, 800x592, 640x480, 480x352, 320x240

A higher frame rate provides smoother motion for videos, and requires more bandwidth. Lower frame rates will result in stuttering motion, and requires less bandwidth.

rate:

Maximum frame

Page 40 of the D-Link Version 1.01 user manual — Audio and Video
Page 40 · click to enlarge
Page 40

Video Quality:

This limits the maximum frame rate, which can be combined with the "Fixed quality" option to optimize the bandwidth utilization and video quality. If fixed bandwidth utilization is desired regardless of the video quality, choose "Constant bit rate" and select the desired bandwidth.

D-Link Version 1.01 — Audio and Video diagram (page 40)
Fig. 50 · Audio and Video

Constant bit rate:

The bps will affect the bit rate of the video recorded by the camera. Higher bit rates result in higher video quality.

Fixed quality:

Select the image quality level for the camera to try to maintain. High quality levels will result in increased bit rates.

Audio in off:

Selecting this checkbox will mute incoming audio.

This setting controls the amount of gain applied to incoming audio to increase its volume.

level:

D-Link Version 1.01 — Audio and Video diagram (page 40)
Fig. 51 · Audio and Video
D-Link Version 1.01 — Audio and Video diagram (page 40)
Fig. 52 · Audio and Video

Audio in gain

Page 41 of the D-Link Version 1.01 user manual — Preset
Page 41 · click to enlarge
Page 41

Preset

This screen allows you to set preset points for the ePTZ function of the camera, which allows you to look around the camera's viewable area by using a zoomed view. Presets allow you to quickly go to and view a specific part of the area your camera is covering, and you can create preset sequences, which will automatically change the camera's view between the different presets according to a defined order and timing you can set.

Video Profile:

This selects which video profile to use.

D-Link Version 1.01 — Preset diagram (page 41)
Fig. 53 · Preset

ePTZ Speed:

You may select a value between 0 and 64. 0 is the slowest and 64 is the fastest.

Use these buttons to move to a specific part of the viewing area, which you can then set as a preset. Click the Home button to return to the center of the viewing area.

Home Button:

Enter the name of the preset you want to create, then click the Add button to make a new preset. If an existing preset has been selected from the Preset List, you can change its name by typing in a new name, then clicking the Rename button.

Name:

Preset List:

Click this drop-down box to see a list of all the presets that have been created. You can select one, then click the GoTo button to change the displayed camera view to the preset. Clicking the Remove button will delete the currently selected preset.

Preset Sequence:

This section allows you to create a preset sequence, which automatically moves the camera's view between a set of preset views.

Arrow Buttons and · Input Preset

Page 42 of the D-Link Version 1.01 user manual — Preset
Page 42 · click to enlarge
Page 42
Preset ListTo add a preset to the sequence, select it from the

drop-down box at the bottom of this window, set the Dwell time to determine how long the camera view will stay at that preset, then click the Add button. The preset name will appear in the list, followed by the dwell time to view that preset for.

You can rearrange your presets in the sequence by selecting a preset in the sequence, then clicking the arrow buttons to move it higher or lower in the current sequence.

Clicking the trash can button will remove the currently selected preset from the sequence.

If you want to change the dwell time for a preset, select it from the list, enter a new dwell time, then click the Update button.

Page 43 of the D-Link Version 1.01 user manual — Motion Detection
Page 43 · click to enlarge
Page 43

Motion Detection

Enabling Video Motion will allow your camera to use the motion detection feature. You may draw a finite motion area that will be used for monitoring. After making any changes, click the Save Settings button to save your changes.

Select this box to enable the motion detection feature of your camera.

D-Link Version 1.01 — Motion Detection diagram (page 43)
Fig. 54 · Motion Detection

Motion:

Sensitivity:

Specifies the measurable difference between two sequential images that would indicate motion. Please enter a value between 0 and 100.

Percentage:

Specifies the amount of motion in the window being monitored that is required to initiate an alert. If this is set to 100%, motion is detected within the whole window will trigger a snapshot.

Draw Motion Area:

Draw the motion detection area by dragging your mouse in the window (indicated by the red square).

Erase Motion Area:

To erase a motion detection area, simply click on the red square that you wish to remove.

Right clicking on the camera image brings up the following menu options:

Select All: Draws a motion detection area over the entire screen. Clear All: Clears any motion detection areas that have been drawn. Restore: Restores the previously specified motion detection areas.

Enable Video

Page 44 of the D-Link Version 1.01 user manual — Sound Detection
Page 44 · click to enlarge
Page 44

Sound Detection

Enabling Sound Detection will allow your camera to use the built-in microphone to trigger events with audio. If this option is selected, the trigger by option under SD recording, Video Clip, or Snapshot should also be selected.

Select this box to enable the sound detection feature of your camera.

D-Link Version 1.01 — Sound Detection diagram (page 44)
Fig. 55 · Sound Detection

Detection:

Detection Level:

Specify the volume level that a sound must exceed in order to trigger the sound detection feature. The higher the number the more sensitive the camera will be to sound.

Click Save Settings to save your changes.

Enable Sound

Page 45 of the D-Link Version 1.01 user manual — Time and Date
Page 45 · click to enlarge
Page 45

Time and Date

This section allows you to automatically or manually configure, update, and maintain the internal system clock for your camera. After making any changes, click the Save Settings button to save your changes.

Time Zone:

Select your time zone from the drop-down menu.

D-Link Version 1.01 — Time and Date diagram (page 45)
Fig. 56 · Time and Date

Select this to enable Daylight Saving Time.

Saving:

Select this option to allow your camera to configure the Daylight Saving settings automatically.

Saving:

Set Date and Time

Selecting this option allows you to configure the Daylight Saving date and time manually.

Manually:

Offset:

Sets the amount of time to be added or removed when Daylight Saving is enabled.

Enable this feature to obtain time automatically from an NTP server.

NTP Server:

NTP Server:

Network Time Protocol (NTP) synchronizes the DCS-2330L with an Internet time server. Choose the one that is closest to your location.

Set the Date and

This option allows you to set the time and date manually.

Time Manually:

Copy Your Computer's Time

This will synchronize the time information from your PC.

Settings:

Enable Daylight · Auto Daylight · Synchronize with

Page 46 of the D-Link Version 1.01 user manual — Media (what to send)
Page 46 · click to enlarge
Page 46

Event Setup

In a typical application, when motion is detected, the DCS-2330L sends images to a FTP server or via e-mail as notifications. As shown in the illustration below, an event can be triggered by many sources, such as motion detection or external digital input devices. When an event is triggered, a specified action will be performed. You can configure the Network Camera to send snapshots or videos to your e-mail address or FTP site.

Event Condition

Action

ex. Motion detection, Periodically, Digital input, System reboot

Media (what to send)

Server (where to send)

ex. Snapshot, Video Clips

ex. Email, FTP

To start plotting an event, it is suggested to configure server and media columns first so that the Network Camera will know what action shall be performed when a trigger is activated.

Page 47 of the D-Link Version 1.01 user manual — Event Setup
Page 47 · click to enlarge
Page 47

The Event Setup page includes 4 different sections.

D-Link Version 1.01 — Event Setup diagram (page 47)
Fig. 57 · Event Setup
  • Server
  • Media
  • Event
  • Recording
1. To add a new item - "event, server or media," click Add . A screen will appear and allow you to update the fields accordingly.
2. To delete the selected item from the pull-down menu of event, server or media, click Delete .
3. Click on the item name to pop up a window for modifying.
Page 48 of the D-Link Version 1.01 user manual — FTP:
Page 48 · click to enlarge
Page 48

Add Server

You can configure up to 5 servers to save snapshots and/or video to. After making any changes, click the Save Settings button to save your changes.

Server Name:

Enter the unique name of your server.

D-Link Version 1.01 — Add Server diagram (page 48)
Fig. 58 · Add Server

E-mail:

Enter the configuration for the target e-mail server account.

FTP:

Enter the configuration for the target FTP server account.

Network Storage:

Specify a network storage device. Only one network storage device is supported.

SD Card:

Use the camera's onboard SD card storage.

Page 49 of the D-Link Version 1.01 user manual — Add Media
Page 49 · click to enlarge
Page 49

Add Media

There are three types of media, Snapshot, Video Clip, and System Log. After making any changes, click the Save Settings button to save your changes.

Media Name:

Enter a unique name for media type you want to create.

D-Link Version 1.01 — Add Media diagram (page 49)
Fig. 59 · Add Media

Snapshot:

Select this option to set the media type to snapshots.

Source:

Set the video profile to use as the media source. Refer to "Audio and Video" on page 39 for more information on video profiles.

Set the number of pre-event images to take. Pre- event images are images taken before the main event snapshot is taken.

image(s) [0~3]:

Set the number of post-event images to take. Post- event images are images taken after the main event snapshot is taken. You can set up to 7 post-event images to be taken.

image(s) [0~7]:

File name prefix:

The prefix name will be added on the file name.

Add date and time

Check it to add timing information as file name suffix.

suffix to file name:

Send pre-event · Send post-event

Page 50 of the D-Link Version 1.01 user manual — Event Setup
Page 50 · click to enlarge
Page 50

Video clip:

Select this option to set the media type to video clips.

Source:

Set the video profile to use as the media source. Refer to "Audio and Video" on page 39 for more information on video profiles.

Pre-event recording:

This sets how many seconds to record before the main event video clip starts. You can record up to 4 seconds of pre-event video.

Set the maximum length of video to record for your video clips.

duration:

Maximum file size:

Set the maximum file size to record for your video clips.

File name prefix:

This is the prefix that will be added to the filename of saved video clips.

System log:

Select this option to set the media type to system logs. This will save the event to the camera system log, but will not record any snapshots or video.

Maximum

Page 51 of the D-Link Version 1.01 user manual — Add Event
Page 51 · click to enlarge
Page 51

Add Event

Create and schedule up to 2 events with their own settings here. After making any changes, click the Save Settings button to save your changes.

Event name:

Enter a name for the event.

D-Link Version 1.01 — Add Event diagram (page 51)
Fig. 60 · Add Event

Enable this event:

Select this box to activate this event.

Priority:

Set the priority for this event. The event with higher priority will be executed first.

Delay:

Select the delay time before checking the next event. It is being used for both events of motion detection and digital input trigger.

Trigger:

Specify the input type that triggers the event.

Motion is detected during live video monitoring. Select the windows that need to be monitored.

Detection:

Periodic:

The event is triggered in specified intervals. The trigger interval unit is in minutes.

System Boot:

Triggers an event when the system boots up.

Network Lost:

Triggers an event when the network connection is lost.

Triggers an event when the PIR sensor is activated by moving infrared objects even in dark environment.

Sensor:

Sound Detection:

Triggers an event when sound is detected during monitoring.

Time:

Select Always or enter the time interval.

Video Motion · Passive Infrared

Page 52 of the D-Link Version 1.01 user manual — Add Recording
Page 52 · click to enlarge
Page 52

Add Recording

Here you can configure and schedule the recording settings. After making any changes, click the Save Settings button to save your changes.

The unique name of the entry.

D-Link Version 1.01 — Add Recording diagram (page 52)
Fig. 61 · Add Recording

name:

Select this to enable the recording function.

recording:

Priority:

Set the priority for this entry. The entry with a higher priority value will be executed first.

Source:

The source of the stream.

Scheduling the recording entry.

schedule:

Configuring the setting for the recording.

settings:

Destination:

Select the folder where the recording file will be stored.

Total cycling recording size:

Please input a HDD volume between 1MB and 2TB for recording space. The recording data will replace the oldest record when the total recording size exceeds this value. For example, if each recording file is 6MB, and the total cyclical recording size is 600MB, then the camera will record 100 files in the specified location (folder) and then will delete the oldest file and create new file for cyclical recording.

Please note that if the free HDD space is not enough, the recording will stop. Before you set up this option please make sure your HDD has enough space, and it is better to not save other files in the same folder as recording files.

Show 4 more labels / short text on this page
Recording entry · Enable this · Recording · Recording
Page 53 of the D-Link Version 1.01 user manual — Event Setup
Page 53 · click to enlarge
Page 53

Size of each file for

If this is selected, files will be separated based on the file size you specify.

recording:

Time of each file

If this is selected, files will be separated based on the maximum length you specify.

for recording:

File Name Prefix:

The prefix name will be added on the file name of the recording file(s).

Page 54 of the D-Link Version 1.01 user manual — SD Card
Page 54 · click to enlarge
Page 54

SD Card

Here you may browse and manage the recorded files which are stored on the SD card.

Format SD Card:

Click this icon to automatically format the SD card and create "picture" & "video" folders.

D-Link Version 1.01 — SD Card diagram (page 54)
Fig. 62 · SD Card

If the picture files are stored on the SD card, click on the picture folder and choose the picture file you would like to view.

Picture:

Playback Recorded Video:

If video files are stored on the SD card, click on the video folder and choose the video file you would like to view.

Refresh:

Reloads the file and folder information from the SD card.

View Recorded

Page 55 of the D-Link Version 1.01 user manual — Advanced
Page 55 · click to enlarge
Page 55

Advanced

ICR and IR

Here you can configure the ICR and IR settings. An IR(Infrared) Cut-Removable(ICR) filter can be disengaged for increased sensitivity in low light environments.

Automatic:

The Day/Night mode is set automatically. Generally, the camera uses Day mode and switches to Night mode when needed.

D-Link Version 1.01 — Advanced diagram (page 55)
Fig. 63 · Advanced

Day Mode:

Day mode enables the IR Cut Filter.

Night Mode:

Night mode disables the IR Cut Filter.

Schedule Mode:

Set up the Day/Night mode using a schedule. The camera will enter Day mode at the starting time and return to Night mode at the ending time.

IR Light Control:

The camera can enable or disable the IR (infrared) light according to your preferences. This setting provides additional controls depending on your specific application.

Off:

The IR light will always be off.

On:

The IR light will always be on.

Sync:

The IR light will turn on when the ICR sensor is on.

Schedule:

The IR light will turn on or off according to the schedule that you specify below.

Page 56 of the D-Link Version 1.01 user manual — HTTPS
Page 56 · click to enlarge
Page 56

HTTPS

This page allows you to install and activate an HTTPS certificate for secure access to your camera. After making any changes, click the Save Settings button to save your changes.

Enable the HTTPS service.

D-Link Version 1.01 — HTTPS diagram (page 56)
Fig. 64

Connection:

Choose the way the certificate should be created. Three options are available:

Method:

Create a self-signed certificate automatically Create a self-signed certificate manually Create a certificate request and install

Status:

Displays the status of the certificate.

The certificate cannot be removed while the HTTPS is still enabled. To remove the certificate, you must first uncheck Enable HTTPS secure connection.

Enable HTTPS Secure · Create Certificate

Page 57 of the D-Link Version 1.01 user manual — Access List
Page 57 · click to enlarge
Page 57

Access List

Here you can set access permissions for users to view your DCS-2330L.

Allow list:

The list of IP addresses that have the access right to the camera.

D-Link Version 1.01 — Access List diagram (page 57)
Fig. 65 · Access List

Start IP address:

The starting IP Address of the devices (such as a computer) that have permission to access the video of the camera. Click Add to save the changes made.

End IP address:

The ending IP Address of the devices (such as a computer) that have permission to access the video of the camera.

Delete allow list:

Remove the customized setting from the Allow List.

Deny list:

The list of IP addresses that have no access rights to the camera.

Delete deny list:

Remove the customized setting from the Delete List.

For example: When the range of the Allowed List is set from 1.1.1.0 to 192.255.255.255 and the range of the Denied List is set from 1.1.1.0 to 170.255.255.255. Only users with IPs located between 171.0.0.0 and 192.255.255.255 can access the Network Camera.

Show 4 more labels / short text on this page
Alowed · Denied · List · List
Page 58 of the D-Link Version 1.01 user manual — LED:
Page 58 · click to enlarge
Page 58

Maintenance Device Management

You may modify the name and administrator’s password of your camera, as well as add and manage the user accounts for accessing the camera. You may also use this section to create a unique name and configure the OSD settings for your camera.

Set a new password for the administrator’s account.

D-Link Version 1.01 — Maintenance Device Management diagram (page 58)
Fig. 66 · Maintenance Device Management

Setting:

Add User Account:

Add new user account.

User Name:

The user name for the new account.

Password:

The password for the new account.

User List:

All the existing user accounts will be displayed here. You may delete accounts included in the list, but you may want to reserve at least one as a guest account.

Camera Name:

Create a unique name for your camera that will be added to the file name prefix when creating a snapshot or a video clip.

Enable OSD:

Select this option to enable the On-Screen Display feature for your camera.

Label:

Enter a label for the camera, which will be shown on the OSD when it is enabled.

Show Time:

Select this option to enable the time-stamp display on the video screen.

LED:

You may specify whether or not to illuminate the status LED on the camera.

Admin Password

Page 59 of the D-Link Version 1.01 user manual — System
Page 59 · click to enlarge
Page 59

System

In this section, you may backup, restore and reset the camera configuration, or reboot the camera.

Save To Local Hard

You may save your current camera configuration as a file on your computer.

D-Link Version 1.01 — System diagram (page 59)
Fig. 67 · System

Drive:

Locate a pre-saved configuration by clicking Browse and then restore the pre-defined settings to your camera by clicking Load Configuration.

Hard Drive:

You may reset your camera and restore the factory settings by clicking Restore Factory Defaults.

Default:

Reboot Device:

This will restart your camera.

Schedule Reboot:

Select this option to schedule a time for the device to reboot.

After making any changes, click the Save button to save your changes.

Local From Local · Restore to Factory

Page 60 of the D-Link Version 1.01 user manual — Firmware Upgrade
Page 60 · click to enlarge
Page 60

Firmware Upgrade

The camera's current firmware version will be displayed on this screen. You may visit the D-Link Support Website to check for the latest available firmware version.

To upgrade the firmware on your DCS-2330L, please download and save the latest firmware version from the D-Link Support Page to your local hard drive. Locate the file on your local hard drive by clicking the Browse button. Select the file and click the Upload button to start upgrading the firmware.

Displays the detected firmware version.

D-Link Version 1.01 — Firmware Upgrade diagram (page 60)
Fig. 68 · Firmware Upgrade

Version:

Displays the camera model name.

Name:

File Path:

Locate the file (upgraded firmware) on your hard drive by clicking Browse.

Upload:

Uploads the new firmware to your camera.

Current Firmware · Current Product

Page 61 of the D-Link Version 1.01 user manual — Status Device Info
Page 61 · click to enlarge
Page 61

Status Device Info

This page displays detailed information about your device and network connection.

D-Link Version 1.01 — Status Device Info diagram (page 61)
Fig. 69 · Status Device Info
Page 62 of the D-Link Version 1.01 user manual — Logs
Page 62 · click to enlarge
Page 62

Logs

This page displays the log information of your camera. You may download the information by clicking Download. You may also click Clear to delete the saved log information.

D-Link Version 1.01 — Logs diagram (page 62)
Fig. 70 · Logs
Page 63 of the D-Link Version 1.01 user manual — Help
Page 63 · click to enlarge
Page 63

Help

This page provides helpful information regarding camera operation.

D-Link Version 1.01 — Help diagram (page 63)
Fig. 71 · Help
Page 64 of the D-Link Version 1.01 user manual — Technical Specifications
Page 64 · click to enlarge
Page 64
Appendix ATechnical Specifications

Technical Specifications

Camera Camera Hardware Profile

ƒƒ 1/4” 1 megapixel CMOS sensor ƒƒ 5 meter IR illumination distance ƒƒ Minimum illumination: 0 lux with IR LED on ƒƒ Built-in Infrared-Cut Removable (ICR) Filter module ƒƒ Built-in PIR sensor (5 meter) ƒƒ Built-in microphone ƒƒ 10x digital zoom

ƒƒ Focal length: 3.45 mm ƒƒ Aperture: F2.0 ƒƒ Exposure time: 1/7.5 to 1/10,000 sec. ƒƒ Minimum object distance: 500 mm ƒƒ Angle of view:

ƒƒ (H) 57.8° ƒƒ (V) 37.8° ƒƒ (D) 66°

Camera Housing ƒƒ IP65 compliant weatherproof housing

Image Features ƒƒ Configurable image size, quality, frame rate, and bit rate ƒƒ Time stamp and text overlays ƒƒ Configurable motion detection windows

ƒƒ Configurable privacy mask zones ƒƒ Configurable shutter speed, brightness, saturation, contrast,

Video Compression ƒƒ Simultaneous H.264/MJPEG format compression ƒƒ H.264 multicast streaming

ƒƒ JPEG for still images

Video Resolution 16:9 - 1280x720, 800x448,640x360, 480x272, 320x176 up to 30 fps recording

4:3 - 960x720, 800x592, 640x480, 480x352, 320x240 up to 30 fps recording

Audio Support G.711, AAC

ƒƒ 10/100 BASE-TX Fast Ethernet port ƒƒ IEEE 802.11n/g/b 2.4GHz single band wireless

ƒƒ MicroSD/SDHC card slot

Network Network Protocols IEEE 802.11n/g/b 2.4GHz single band wireless IPv6 IPv4 TCP/IP UDP ICMP DHCP client NTP client (D-Link) DNS client DDNS client (D-Link) SMTP client FTP client

HTTP / HTTPS Samba Client PPPoE UPnP port forwarding RTP / RTSP/ RTCP IP filtering QoS CoS Multicast IGMP ONVIF compliant

Security ƒƒ Administrator and user group protection ƒƒ Password authentication

ƒƒ HTTP and RTSP authentication

and sharpness · External Device Interface

Page 65 of the D-Link Version 1.01 user manual — Technical Specifications
Page 65 · click to enlarge
Page 65
Appendix ATechnical Specifications

System Requirements for Web Interface

ƒ ƒ Operating SystemMicrosoft Windows 8/7/Vista/XP/2000 ƒ ƒ Browser: Internet Explorer, Firefox, Chrome, Safari

Event Management ƒƒ Motion detection ƒƒ Event notification and uploading of snapshots/video clips via

ƒƒ Supports multiple SMTP and FTP servers ƒƒ Multiple event notifications ƒƒ Multiple recording methods for easy backup

ƒƒ Take snapshots/video clips and save to local hard drive ƒƒ Configuration interface accessible via web browser

Mobile Support Windows 8/7/Vista/XP system, Pocket PC, or mobile phone mydlink mobile app for iOS and Android mobile devices

ƒ ƒ Operating SystemMicrosoft Windows 8/7/Vista/XP ƒ ƒ Web Browser: Internet Explorer 7 or higher
ƒ ƒ ProtocolStandard TCP/IP

ƒƒ Remote management/control of up to 32 cameras ƒƒ Viewing of up to 32 cameras on one screen

ƒƒ Supports all management functions provided in web interface ƒƒ Scheduled motion triggered, or manual recording options

General Weight 134 g ± 5%

External Power Adaptor Input100 to 240 V AC, 50/60 Hz Output: 5 V DC, 1.2 A

Power Consumption 5 Watts

Temperature Operating: -25 to 45 °C (-13 to 113 °F) Storage: -20 to 70 °C (-4 to 158 °F)

Humidity Operating20% to 80% non-condensing Storage: 5% to 95% non-condensing

Certifications ƒƒ CE ƒƒ FCC

ƒƒ C-Tick ƒƒ IC

Show 5 more labels / short text on this page
System Management · e-mail or FTP · Remote Management · D-ViewCam™ System Requirements · D-ViewCam™ Software Functions
Page 66 of the D-Link Version 1.01 user manual — Technical Specifications
Page 66 · click to enlarge
Page 66
Appendix ATechnical Specifications
D-Link Version 1.01 — Technical Specifications diagram (page 66)
Fig. 72 · Technical Specifications
Sources

References & links

Pages referenced in this manual — manufacturer, support and downloads.

Ask about the D-Link Version 1.01

Owners and our team usually reply within a day — and your question helps the next person too.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
No questions yet about the D-Link Version 1.01

Be the first to ask — other owners or our team will answer.

Original document

D-Link Version 1.01 manual PDF

66 pages·4.4 MB·Home Security System·PDF
Click any page above to open it here
Page 1 / …
100%
Loading pages…