Instruction/ maintenance manual of the product CS-8050 CrimeStopper
Go to page of 8
CS-8050 HANDS-FREE KEYLESS ENTRY / IMMOBILIZER SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Hands-Free Keyless En try & Immobilizer System by Crimestopper Security Products Inc. This booklet contains the inf ormation necessary for installing, using, and maintaining your alarm system.
INSTALLATION PRECAUTIONS & WARNINGS BEFORE BEGINNING , check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS, ABS BRAKES, AND BATTERY). DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with brake, and gas pedals, steering column, or any other moving parts in the vehicle.
WIRING WIRE #5: +12Volt Power Input: Connect to Battery Positive Terminal. WIRE #6: Immobilizer Circuit #1 Output: This is part of the immobilizer circuit (on-board relay). Cut the Ignition wire and connect ONE end to this wire. WIRE #7: Immobilizer #1 Input: This is part of the immobilizer circuit (on-board relay).
POWER DOOR LOCK WIRING NEGA T IVE TRIGGE R DOORLOCK WIRI NG POSI TIVE TRIGGER DOO RLOCK WIRING GREEN GREEN FUSED RED +12V RED BLUE + BLUE 86 85 86 85 87 87 30 87A 30 87A FAC T O RY FAC T O RY L L POWE.
OPERATING INSTRUCTIONS How the System Works: (Hands-Free Mode) As you turn your Ignition OFF and leave your vehicle, the system will automatically arm. The tiny hands-free remote transmitter on your key chain emits a low power signal every few seconds.
ORERATING INSTRUCTIONS Turning the Remote OFF (Stop sending signals): Press and hold the remote button for 5 seconds until LED on remote flashes twice (Ignore first single flash).
HANDS-FREE TRANSMITTER PROGRAMMING This system can code learn up to 4 different transmitters. All transmitters must be learned at one time. 1. Turn ignition switch on and off 3 times leaving it on the 3 rd time. (on/off, on/off, on) LED will Flash 3 times.
IMMOBILIZER CIRCUIT #1 #1 #2 RED PLUG: LE D BLUE PLUG: V ALET CS-8050 LED #3 V ALET/ PROGRA M SWITCH + BATTERY (-) NEGA TIVE ARMED OUT PUT IGNITION - #4 #5 #6 +12V GROUN D #7 (-) NEG.
An important point after buying a device CrimeStopper CS-8050 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought CrimeStopper CS-8050 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data CrimeStopper CS-8050 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, CrimeStopper CS-8050 you will learn all the available features of the product, as well as information on its operation. The information that you get CrimeStopper CS-8050 will certainly help you make a decision on the purchase.
If you already are a holder of CrimeStopper CS-8050, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime CrimeStopper CS-8050.
However, one of the most important roles played by the user manual is to help in solving problems with CrimeStopper CS-8050. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device CrimeStopper CS-8050 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
