Instruction/ maintenance manual of the product CS-2003DC SERIES II CrimeStopper
Go to page of 18
CS-2003DC & CS-2003DC Series II REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle™ Remote Al arm System by Crimestopper Security Products Inc. This booklet contains the information nece ssary for installing, using, and maintaining your alarm system.
TABLE OF CONTENTS Installation Cautions & Warn ings…….………………………… ……………………………………………………2 Control Module Mounting……… ….…………………………………………… ..……………………….
CONTROL MODULE MOUNTING DO NOT Mount the control unit in the engine compartment! DO NOT Mount the control unit or wiring harness wh ere they can become entangled with moving parts such as brake/gas/clutch peda ls, or the steering column! The alarm control module should be mounted in a concealed location.
WIRING PIN 1: GRAY WIRE: INPUT SOURCE FOR REMOTE OUTPUT 1 RELAY Connect to a +12 Volt or Chassis Grou nd sour ce depending on the output requ ired for PIN 2 Gray wire See Below. PIN 2: GRAY WIRE: REMOTE OUTPUT 1 On-Board Relay (Optional) Connect this wire to an AUX device or Function.
WIRING PIN 11: YELLOW WIRE: IGNITION SWITCHED “ON” +12 VOLTS INPUT Connect to an Ignition Wire (or Fuse in the fuse box) that shows +12 Volts pow er when the key turned “On”, when the car is “Cranking”, and when the car is running.
POWER DOOR LOCK WIRING (ON-BOARD RELAYS) WHITE WIRE: DOOR LOCK [Switch Side, Term 87A] Reverse Polarity and Aftermarket Systems. GREEN: DOOR LOCK OUTPUT [Motor Side, Term 30] Reverse Polarity, Positive , Negative and Aftermarket Systems. BLUE: DOOR UNLOCK OUTPUT [Motor Side , Term 30] Reverse Polarity, Posi tive, Negative and Aftermark et.
SEPARATE DRIVER’S DOOR UNLOCK WIRING NEGA TIV E TRI GGER DO OR LOCKS GREEN DRIVER'S DOOR MOTOR L L UL UL FA C T O R Y L O C K RELA YS +12V + FUSED UNLOCK WIRE CUT +12V FUSED WHITE GREEN BLUE BR.
TRANSMITTER PROGRAMMING This system will learn a maximu m of 3 transmitters total. 1. Turn Ignition ON/OFF…ON/OFF …O N. You should hear (3) chirps. 2. Press the Program/Override Button 5 times and you should hear 5 light flas hes and 5 siren chirps.
OPTION PROGRAMMING PROGRAMMABLE OPTIONS 1. Turn the Ignition ON and press the Override/Pro gram button 5 times. Yo u should hear a long confirmation chirp. 2. Within the next few seco nds, pre ss the Override/Progr am button [again] the number of times that correspon ds to the feature list below.
OPTION PROGRAMMING 1. HORN CHIRPS / PULSES This option controls the system’s Fa ctory Vehicle Horn outp ut. There are 3 selections: Button 1 (Lock) = Horn Pulse only when alarm is tripped. Button 2 (Unlock) = Horn Chirps for Arm / Disa rm and Pulse when tripped.
OPTION PROGRAMMING 9. PARKING LIGHTS ON WITH DISARM Keeps parking lights on instead of 2 flashes when system i s di sarmed to assist i n locating your vehicle in a crowded parking lot or structure. Light will stay on for 30 Sec. or until Ignition is turned on.
CUSTOM OVERRIDE Custom override allows the user to se t a specific number of bu tton presses (2-15) required to perform an emergency override/disarm of the alarm system. This increa ses the level of security of the system, but you MUST MEMORIZE how many button presses you have changed your system to use or the unit will not disarm in an emergency.
OPERATING INSTRUCTIONS ACTIVE ARMING To arm the alarm and lo ck the doors, press the #1 (L ock Symbol) button on the transm itter. You will hear a single siren chirp and the lights will flash once. The system will arm, the do ors will lock and th e starter will be disabled if these optional features are installed.
OPERATING INSTRUCTIONS PROGRAMMABLE SILENT ARM/DISARM MODE The system can be silently armed and disarmed as norma l with Lock/Unlock Buttons, but no siren chirp.
OPERATION OPEN ZONE ALERT/BYPASS If the system detects a faulty or open zone (Door left open) when the system is ACTIVELY ARMED, the siren will chirp 4 times along with 4 light flashes.
CARJACK PROTECTION PASSIVE CARJACK This feature provides Passive Carjack protection and must be enabl ed before use through Alarm programming options (13) & (14).
CS-2003DC SERIES II This page applies to CS2003DC Series II systems ONLY: 5-Button Remote Functions: BANK #1 (Directly Press Buttons) Button 1: Arm Button 2: Disarm Button 3: Aux #1 (Trunk) Button 4: .
CS-2003DC SERIES II DASH UNDER IN DASH Use "L" Bracket OR LED / VALET BUTTON MOUNTING:.
An important point after buying a device CrimeStopper CS-2003DC SERIES II (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought CrimeStopper CS-2003DC SERIES II yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data CrimeStopper CS-2003DC SERIES II - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, CrimeStopper CS-2003DC SERIES II you will learn all the available features of the product, as well as information on its operation. The information that you get CrimeStopper CS-2003DC SERIES II will certainly help you make a decision on the purchase.
If you already are a holder of CrimeStopper CS-2003DC SERIES II, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime CrimeStopper CS-2003DC SERIES II.
However, one of the most important roles played by the user manual is to help in solving problems with CrimeStopper CS-2003DC SERIES II. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device CrimeStopper CS-2003DC SERIES II along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
