Instruction/ maintenance manual of the product W810 Creda
Go to page of 16
INSTRUCTIONS for INST ALLA TION and USE Gas Hob W810 T o the Installer Before installation fill in the pr oduct details on the back co ver of this booklet. The information can be f ound on the rating plate. T o the User Y ou m ust read the instructions prior to using the appliance and then retain them for future ref erence .
Introduction 3 CONTENTS For Y our Safety – Always 4 For Y our Safety – Never 5 Installation 9 - 14 Using The Hob 6 Care & Cleaning 7 Something Wrong? 8 Key contacts Back Cover 2 Retention of t.
INTR ODUCTION Y our new hob is guaranteed* and will give lasting service. This guarantee is only applicable if the appliance has been installed in accordance with the installation instructions detailed in this booklet. T o help make best use of your cooking equipment, please read this booklet carefully .
FOR Y OUR SAFETY When used properl y , y our appliance is completely safe b ut as with any product there are certain precautions that must be observed. PLEASE READ THE PRECA UTIONS BELO W BEFORE USING Y OUR APPLIANCE. AL W A YS ● Always make sure you understand the controls prior to using the appliance.
NEVER ● Never leave children unsupervised where a cooking appliance is installed as all cooking surfaces will be hot during and after use. ● Never allow anyone to sit or stand on any part of the appliance. ● Never store items above the appliance that children may attempt to reach.
USING THE GAS HOB - FEA TURES 6 DO NO T allow y oung children near to the appliance when the hob is in use as the surfaces get extremely hot. In order to obtain maximum performance from the burners, u.
Clean the hob regularly and wipe up spills soon after they occur to prevent them from becoming burnt on. 1. Household abrasive powders, e.g. Vim. 2. Oven chemical cleaners, aerosols and oven pads. Caustic cleaners such as these will etch the surface and attack the metal frame.
8 This appliance conforms to the following EEC Directives: Low V oltage Equipment 73/23/EEC 93/68/EEC Electromagnetic Compatibility 89/336/EEC 92/31/EEC 93/68/EEC Gas Appliances 90/396/EEC 93/68/EEC T o minimise the risk of injury to children please dispose of your product carefully and safely .
INST ALLA TION - electrical requirements 9 Connection to the electricity supply should be made via a properly ear thed, readily accessible wall socket which is adjacent to but not directly above , and not more than 1.25m away from the appliance and capable of electrical isolation.
INST ALLA TION INSTR UCTIONS 10 Gas Connection Pressure test point Gas rate adjustment Aeration adjustment Electrical Connection Rp 1 / 4 ( 1 / 4 ” BSP female) Burner injector None None 230-240V ac. 50Hz Heat resistant PVC 85 o C 0.75mm2 Flexible cord.
GAS SAFETY (INST ALLA TION & USE) REGULA TIONS LOCA TION PRO VISION FOR VENTILA TION INST ALLA TION INSTR UCTIONS 11 Prior to installation, ensure that the local distributions (nature of the gas and gas pressure) and the adjustment conditions are compatible.
The hob is designed to fit into worktop and base unit(s) with a cutout as shown in Fig.1. Any obstruction such as supports or side panels must be removed to allow 30mm minimum depth below the worktop cutout. Any overhead surface of combustible material must not be closer than 600mm.
13 INST ALLA TION Fig. 1 IMPORT ANT Minimum unobstructed depth 50mm Worktop thickness Preferred 30-40mm 19mm minimum recommended 30mm 489mm 558mm Front edge of worktop Note: Do not over tighten the hob c lamps as distor tion of the hob may occur . Fig.
INST ALLA TION INSTR UCTIONS 14 Read the Gas Hob instructions before conversion, installation and using the Gas Hob. 1 Rapid burner injector marked 92 - 1 off 2 Semi-rapid burner injector marked 72 - 2 off 3 Auxillary burner injector marked 55 - 1 off Ensure that the Gas Hob is disconnected from the gas and electricity supply (Fig.
15 FP089-01 Creda Gas Hob (W810) 12/09/2001 5:02 pm Page 15.
FP089 - 01 K ey Contacts Service Creda has the largest appliance manufacturer ’s service team in Europe, trained specialists directly employed by us to ensure your complete confidence. Repair Service UK: 08709 066 066 Republic of Ireland: 1850 302 200 Y ou will be asked for the following information:- Name, address and postcode.
An important point after buying a device Creda W810 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Creda W810 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Creda W810 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Creda W810 you will learn all the available features of the product, as well as information on its operation. The information that you get Creda W810 will certainly help you make a decision on the purchase.
If you already are a holder of Creda W810, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Creda W810.
However, one of the most important roles played by the user manual is to help in solving problems with Creda W810. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Creda W810 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
