Instruction/ maintenance manual of the product G8693 Craftsman
Go to page of 30
MINI SHAPER MODEL G8693 INSTRUCTION MANUAL COPYRIGHT © 2000 BY GRIZZLY INDUSTRIAL, INC. 1821 VALENCIA ST., BELLINGHAM, WA 98227 WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
-2- G8693 Mini Shaper.
G8693 Mini Shaper -3- Table Of Contents PAGE 1. SAFETY SAFETY INSTRUCTIONS FOR POWER TOOLS ................................................3-4 ADDITIONAL SAFETY INSTRUCTIONS FOR SHAPERS ......................................5 2. CIRCUIT REQUIREMENTS 110V OPERATION .
-4- G8693 Mini Shaper Safety Instructions For Power Tools SECTION 1: SAFETY 5. KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe distance from work area. 6. MAKE WORK SHOP CHILD PROOF with padlocks, master switches, or by removing starter keys.
G8693 Mini Shaper -5- 9. USE PROPER EXTENSION CORD . Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
-6- G8693 Mini Shaper Safety Instructions For Shapers 1 . Wear eye protection. 2. Wear ear protection. 3. Be sure keyed washer is directly under spindle nut and that spindle nut is tight. 4. Feed workpiece against rotation of cutter. 5. Do not use awkward hand positions.
G8693 Mini Shaper -7- Figure 1. Improper connections of the electrical-grounding conductor can result in risk of electric shock. The conductor with green or green and yellow striped insulation is the electrical-grounding conductor.
-8- G8693 Mini Shaper SECTION 3: GENERAL INFORMATION To operate this, or any power tool, safely and efficiently, it is essential to become as familiar with its characteristics as possible. The time you invest before you begin to use your Model G8693 will be time well spent.
G8693 Mini Shaper -9- Parts Inventory After all parts have been removed from the box, you should have: 1 Mini Shaper Unit 3 Knobs 1 Fence Assembly 1M i t er Gauge 2 Spindle Wretches 1 Router Bit Colle.
Many of the solvents commonly used to clean machinery can be highly flammable, and toxic when inhaled or ingested. Always work in well-ventilated areas far from potential ignition sources when dealing with solvents. Use care when disposing of waste rags and towels to be sure they do not create fire or environmental hazards.
G8693 Mini Shaper -11- SECTION 4: ASSEMBLY Spindle Shaft For Your Own Safety, Never Connect To Power Source Until All Assembly Steps Are Complete, And You Have Read And Understand The Safety And Operational Instructions. Typically, the Spindle Shaft is already installed from the factory.
-12- G8693 Mini Shaper Fence 1. Find three Knobs (REF 14) and three rubber faced Washers (REF 13) from the parts bag. 2. Mount the Fence Body (REF 12) on the Table (REF 10) using two knobs and washers. Screw the knobs through the slots of the fence body and into the threaded holes near the rear of the table.
G8693 Mini Shaper -13- Site Consideration If the Mini Shaper is to be used in a permanent location, it should be fastened securely to a firm supporting surface such as a workbench. Holes should be drilled through supporting surface of the workbench as illustrated.
-14- G8693 Mini Shaper SECTION 4: OPERATIONS Figure 7. Location Of Primary Components. Operating this equipment has the potential for hearing damage to occur, especially if operated for a long period of time. Always wear hearing protection when operating equipment.
G8693 Mini Shaper -15- The “On-Off” switch is located on the front of your Mini Shaper and has the operating positions clearly marked. Push the switch up to turn your tool “On” and down to turn it “off” The switch has a switch key which, when removed, allows the switch to be locked in the “off” position.
-16- G8693 Mini Shaper The Spindle has a maximum vertical adjustment of 3 ⁄ 4 ''. The large knob on the rear of the Shaper/ Router is used to set the height. Loosen the knob by turning it counterclockwise. The Spindle assembly can now be raised or lowered by mov- ing the knob right or left in the inclined slot.
G8693 Mini Shaper -17- The Ring Guard (REF 19) is an important safety feature and should always be used when shap- ing. Before the Mini Shaper is turned on, the ring guard should be positioned approximately 1 ⁄ 4 '' above the workpiece and locked in place.
-18- G8693 Mini Shaper Before making any adjustments or conversions to the Mini Shaper, make sure the switch is in the 'OFF' position and the power cord is UNPLUGGED. Be sure the Table Insert (REF 16) is installed and not in contact with the cutter prior to operation.
G8693 Mini Shaper -19- Figure 16. Do not use the Mini Shaper to reduce workpiece size. The workpiece should be cut as close to final size before shaping. For best results, run all sides to be shaped through a jointer. Whenever a cutter is required to make a heavy cut, the spindle speed (RPM) may be reduced.
-20- G8693 Mini Shaper Always install the keyed washer directly under the jam nut; otherwise, the nut may loosen and serious injury may result. A cross-grain cut will result in splintering of the back edge. Two common methods to reduce this problem are: 1.
G8693 Mini Shaper -21- When shaping long, wide or cumbersome work- pieces, the table may be too small to provide full support. An extension for the table can be added to the sides and front. Use only smooth, flat wood and be sure the extension is on the same level as the Mini Shaper table.
-22- G8693 Mini Shaper Figure 19. Your Mini Shaper has a rear chip discharge which fits any standard dust collection with a 2 1 ⁄ 2 '' hose. A 2 1 ⁄ 2 '' to 1 1 ⁄ 4 '' hose adapter is supplied with the Mini Shaper. Attaching a dust collection system will keep your work area cleaner.
G8693 Mini Shaper -23- Keep your Mini Shaper clean and adjusted prop- erly for maximum performance and machine longevity. Do not allow pitch to accumulate on the table, fences or cutters. Clean frequently with Gum and Pitch Remover. The table and other non-painted surfaces on the Model G8693 should be protected against rust and pitting.
-24- G8693 Mini Shaper The Model G8693 was specifically designed for Shaping . DO NOT MODIFY AND/OR USE THIS MACHINE FOR ANY OTHER PUR- POSE. Modifications or improper use of this tool will void the warranty. If you are con- fused about any aspect of this machine, DO NOT use it until you have answered all your questions.
G8693 Mini Shaper -25- Design Type .................................................................................................... Bench Model Overall Dimensions: Table .............................................................................
-26- G8693 Mini Shaper 20 17 18 15 14 14 12 60 21 69 68 70 16 68 11 66 18 67 65 14 57 10 58 3 1 31 71 2 5 8 4 9 6 7 14 19 24 47 55 46 61 71 3 44 50 45 51 48 49 40 27 28 42 26 25 54 48 39 38 41 37 35 3.
G8693 Mini Shaper -27- Ref Part No Description 36 P8693036 SHAPER NUT 37 PR09M EXTERNAL SNAP RING 20MM 38 P6004 6004-2RS BALL BEARING 39 P8693039 SPINDLE CARTRIDGE 40 P6202 6202-2RS BALL BEARING 41 PR.
-28- G8693 Mini Shaper Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
G8693 Mini Shaper -29- CUT ALONG DOTTED LINE 10. Which benchtop tools do you own? Check all that apply. ___1" x 42" Belt Sander ___6" - 8" Grinder ___5" - 8" Drill Press .
FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 Place Stamp Here TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name_____________________________.
An important point after buying a device Craftsman G8693 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Craftsman G8693 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Craftsman G8693 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Craftsman G8693 you will learn all the available features of the product, as well as information on its operation. The information that you get Craftsman G8693 will certainly help you make a decision on the purchase.
If you already are a holder of Craftsman G8693, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Craftsman G8693.
However, one of the most important roles played by the user manual is to help in solving problems with Craftsman G8693. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Craftsman G8693 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
