Instruction/ maintenance manual of the product 2600 3M
Go to page of 20
Instructions Fibrlok TM 2600 Series Multi-Fiber Optical Splice Issue 2, May 1993.
2.
3 Contents: 1.0 General .......................................................................................................................................................... 3 2.0 Preparation Kit ..................................................
4 .50" (1.27 cm) 1.50" (3.81 cm) .265" (.673 cm).
5 1.0 General The Fibrlok TM 2600 Series Multi-Fiber Optical Splicing System provides permanent mechanical splices for single-mode or multimode optical fibers with a nominal cladding diameter of 125 m.
6 3M Part # Construction Color 2634 12 fiber bonded or ribbonized Light Y ellow 2635 12 fiber A T&T ASR White 2637 10 fiber bonded or ribbonized Light Gray 2639 8 fiber bonded or ribbonized Light .
7 4.04 Connect the power cord from the AC adapter to the stripper handle. Plug the AC adapter into an electrical outlet. Note: An optional 6 volt battery and cord are available. 4.05 Arrange the fibers in the splice tray per tray instructions. T rim the ribbon end so that it extends approximately 3/4" (19 mm) beyond the center of the splice.
8 4.09 Release the handles. Clean the stripped fibers with alcohol and a lint free cloth. Inspect for broken fibers. Repeat steps 4.05 through 4.09 if necessary .
9 6.0 Cleaver Operation 6.01 The Alcoa Fujikura Model CT-03, CT -04, CT -04B, or CT -07, is required for the cleaving process. Note: Sumitomo Model FC-4 Cleaver may also be used, along with the 2651-A Fiber Viewer . 5.03 Lay the stripped ribbon between the guide forks.
10 6.04 Lock the spacer in place by tightening the locking screw using the supplied allen wrench. 6.05 Place the ribbon holder into the cleaver . Push the ribbon holder against the cleaver spacer gauge . 6.06 Align the end of the ribbon coating to be within the slot in the cleaver gauge.
11 6.09 Depress the cleaving lever 3 firmly . 6.10 While holding the cleaving lever down, remove the cleaved fiber stubs, and dispose of per company practice. 7.0 Visual Inspection of the Cleave 7.01 Install the fiber viewer on the cleaver and rotate the viewer barrel to focus.
12 7.03 Defect in cleaved fibers. 7.04 If fibers are properly cleaved: - Remove the fiber viewer from the cleaver , and - Remove the ribbon holder from the cleaver . defective Actuation Lever Preload Lever Preload Lever 8.0 Fiber Insertion 8.01 Move the actuation lever on the actuator tool all the way to the right.
13 8.05 Lower the front end of the ribbon holder to lay the cleaved fibers in the V grooves of the splice. If the fibers are not positioned properly in the V grooves, raise and lower the front end of the ribbon holder until the fibers are positioned properly .
14 10.0 Splice Actuation 10.01 Actuate the splice by squeezing the actuation lever slowly until it stops. 10.02 Close both splice covers. Note: Some protective gel may be visible after closing covers. 9.02 Look at the amount of bare glass where each ribbon enters the splice.
15 10.05 Turn the splice over and verify that the wedge has been fully pushed against the splice body . 10.06 If the wedge is not against the splice body , move the actuation lever to the right, place the splice back into the actuator tool and squeeze the actuation lever again.
16 c. Insert the tube guide into the pivot housing. Secure the tube guide with the tube guide lock. 1 1.02 Stripper Blades - Cleaning a. If the stripper performance is unsatisfactory after the normal cleaning procedure (section 4.10), the stripper blades may need to be removed from the handle assembly for a more thorough cleaning.
17 1 1.03 Stripper Blades - Replacement a. If the stripper performance is unsatisfactory after a thorough cleaning, the blades need to be replaced. Remove the blades per 1 1.02 b. b. Place the new blades into the pivot housing per 1 1.02 d and e. Hint 2: Stripping in Hot T emperatures: At high temperatures, the heating time will be less.
18 P/N Description Packaging Splices 2604 Fibrlok TM Multi-Fiber Optical Splice (4 Fiber) 3/Pkg; 4 Pkg/ Case 2606 Fibrlok TM Multi-Fiber Optical Splice (6 Fiber) 3/Pkg; 4 Pkg/ Case 2608 Fibrlok TM Mul.
19.
Litho in U.S.A. 3M Telecom Systems Group Important Notice All statements, technical information and recommendations related to the Seller's products are based on information believed to be reliable, but the accuracy or completeness thereof is not guaranteed.
An important point after buying a device 3M 2600 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought 3M 2600 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data 3M 2600 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, 3M 2600 you will learn all the available features of the product, as well as information on its operation. The information that you get 3M 2600 will certainly help you make a decision on the purchase.
If you already are a holder of 3M 2600, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime 3M 2600.
However, one of the most important roles played by the user manual is to help in solving problems with 3M 2600. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device 3M 2600 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
