Instruction/ maintenance manual of the product 320.61199 Craftsman
Go to page of 30
Operator's Manual C RI:IF MRN°I X E 12-Volt Lithium-Ion Cordless Multi-Tool Model No. 320.61199 c_ius LISTED _k WARNING: To reduce the risk of injury, the user must read and understand the Operator's manual before using this product.
Warranty page 2 Safety Symbols page 3 Safety Instructions pages 4-12 Description page 13 Assembly pages 13-14 Operation pages 14-22 Application Page 23 Maintenance pages 24-25 Troubleshooting page 26 .
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful attention and understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures.
Some of these following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME DESIGNATION/EXPLANATION V Volts Voltage A Amperes Current Hz Hertz Frequency (cycles per second) W Watt Power rain Minutes Time "k.
GENERAL SAFETY RULES _, WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. The term "power tool" in all of warnings listed below refers to corded power tools or battery-operated (cordless) power tools.
PERSONAL SAFETY Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
POWER TOOL USE AND CARE Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and more safely at the rate for which it was designated. Do not use the power tool if the switch does not turn it ON and OFF.
BATTERY TOOL USE AND CARE • Make sure that the switch is in the OFF position before inserting the battery pack. Inserting the battery pack into power tools that have the switch ON invites accidents. Recharge only with the charger specified by the manufacturer.
SERVICE • Have your power tool serviced by a qualified repair person. • When servicing a power tool, use only identical replacement parts. • Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance instructions may create a risk of shock or injury.
• Only use application accessories in good condition. Do not use them if they are torn or worn. • Do not restart a cutting operation in the workpiece. To resume a cutting operation: while keeping the tool from contacting the workpiece, allow the tool reach full speed and then carefully guide the cutting accessory into the cut.
• Keep the cord and charger from heat to prevent damage to housing or internal parts. • Do not allow gasoline, oils, petroleum-based products, etc. to come in contact with plastic parts. These materials contain chemicals that can damage, weaken, or destroy plastic.
I M PORTANT SAFETY INSTRUCTIONS • Save these instructions. This manual contains important safety and operating instructions for 12V Multi-Tool 320.61199.
I D] =_.'_o_[[o_] KNOW YOUR MULTI-TOOL (Fig.l) PRODUCT SEPCIFICATION Motor 12 Volt DC Tool Weight (with battery) 1.81bs Oscillation Rate 15000/Min Oscillation Angle _+1.
• If any part is damaged or missing, please refer to the numbers listed on the back page of operator's manual. PACKING LIST Multi-Tool, straight edge flush cut blade, circular saw blade, harden.
BATTERY PROTECTION). BATTERY PROTECTION The battery circuitry protects the battery pack from extreme temperature, over discharge, and over-charge. To protect the battery from damage and prolong its life, the battery pack circuitry will turn off the battery pack if it becomes overloaded or if the temperature becomes too high during use.
HOW TO CHARGE THE BATTERY PACK NOTE: This Lithium-ion battery pack is shipped partially charged. Before using it the first time, fully charge the battery pack. A fully discharged battery pack will charge in about 30 minutes in an environment between 32 ° F (0 ° C) and 104 ° F (40 ° C).
CHARGING A HOT BATTERY PACK If the battery pack is above normal temperature range, the red LED will illuminate and the green LED will be off. When the battery pack cools down to approximately 104°F (40°C), the charger will automatically begin charging.
TO DETACH BATTERY PACK (Fig. 4) 1. Make sure that the tool is "OFF" 2. Depress the battery release buttons located on the both sides of th of the battery pack to release the battery pack. 3. Pull the battery pack out and remove it from the tool.
DETACHABLE VACUUM ADAPTOR (Fig.7) Always connect the vacuum adaptor when sanding. Remove the application tool before mounting the vacuum adaptor. To improve dust extraction from the working area, insert the dust-extraction adaptor into the rear of the tool, and connect the adaptor to a dust-extraction system or a suitable vacuum cleaner.
Fig. 8 Fig. 9 Fig. 10 Ribs on shaft Grooves Fig. 11 0 30 60 120 150 180' 90 _ 240' 330' 210 270' 300' MOUNTING/CHANGING THE SANDPAPER (Fig.
SAWING Fig. 13 & WARNING: Use sharp, undamaged saw blades only. Deformed, blunt saw blades or saw blades that are otherwise damaged can break. WARNING: When sawing light building materials, observe the statutory provisions and the recommendations of the material suppliers.
SANDING WARNING: Do not touch the gear box after prolonged use; it could be very hot. • The removal rate and the sanding pattern are determined by the choice of sanding sheet and the work surface. • Apply uniform sanding pressure to extend the life of the sanding sheets.
r:1 -,J -,J al [t]_aiil[,) _ i ACCESSORY APPLI CATION Carbide Circular Adhesive Removal Blade Carbide Triangular Rasp Hardened Steel Scraping Blade High Speed Steel Circular Saw Blade High Carbide ste.
_, WARNING: To avoid serious personal injury, always remove the battery pack from the tool when cleaning or performing any maintenance. _1, WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other parts may create a hazard or cause product damage.
(26°C) and free of moisture. • Store Lithium-Ion battery packs in a 30%-50% charged condition. • Every six months of storage, fully charge the Lithium-Ion battery pack.
PROBLEM CAUSE SOLUTION The tool does not work Battery is depleted Charge the battery Motor overheating Be sure cooling vents Clean, clear vents. Do are free from dust and not cover with hand obstacles.
12 VOLT LITHIUM-ION CORDLESS MULTI-TOOL MODEL NUMBER 320.61199 The Model Number will be found on the Nameplate attached to the handle of the Multi-Tool.
61199 Manual_Revised_09 0310 Page 28.
61199 Manual_Revised_09 0310 Page 29.
Your Home For expert troubleshooting and home solutions advice: manage home www.managemyhome.com For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and co.
An important point after buying a device Craftsman 320.61199 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Craftsman 320.61199 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Craftsman 320.61199 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Craftsman 320.61199 you will learn all the available features of the product, as well as information on its operation. The information that you get Craftsman 320.61199 will certainly help you make a decision on the purchase.
If you already are a holder of Craftsman 320.61199, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Craftsman 320.61199.
However, one of the most important roles played by the user manual is to help in solving problems with Craftsman 320.61199. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Craftsman 320.61199 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
