Instruction/ maintenance manual of the product 247.77763 Craftsman
Go to page of 10
Owner's Manual CRRFTSMRN -6.5 Horse Power Self-Propelled CHIPPER-SHREDDER VACUUM Model No. 247.77763 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. In H H H p m ° | m Sears, Roebuck and Co.
Content Page Content Page Warranty Information 2 Service & Adjustment 15 Safe Operation Practices 3 Off-Season Storage 17 Assembly 5 Trouble-Shooting 18 Operation 8 Parts Ust 19 Maintenance 13 One.
This symbol points out Important safety instructions which, if not followed, could endanger the per- sonal safety and/or property of yourself and others. Read and follow all instructions in this manual before attempting to operate your chipper-shredder vacuum.
seconds after the engine is shut off. Never place any part of the body in the impeller area untilyou are sure the impeller has stopped rotating. Keep all guards and safety devices in place and operating propedy.
Right Left Front Catcher Bag Chipper Chute with Support Bracket 20-oz. Bottle of Engine Oil Figure I Nozzle Spark Plug Wire IMPORTANT: This unit is shipped without gasoline or oil in the engine. After assembly, see OPERATION section of this manual for proper fuel and engine oil flU-up.
Attaching the Nozzle (See Figure 3.) • Remove the three plastic wing nuts from the front of the chipper-shreddervacuum. • Place the nozzle over the three weld studs.
Flange Nuts Weld Hex Nuts & Hex Bolts & Bell Washers Saddle Washers Figure 6 • Place the chipper chute over the weld studs keeping the slotted side towards the bottom. Loosely secure with the three hex nuts and bell • washers that were removed earlier.
Know Your Chipper-Shredder Vacuum Read this owner's manual and safety rules before operating your chipper-shredder vacuum. Compare the illustrations below with your equipment to familiarize yourself with the location of various controls and n adjustments.
Gas And Oil Fill-up Oil (one 20-oz. bottle shipped with unit) Only use high quality detergent oil rated with API service classificationSF, SG or SH. Select the oil's viscosity grade according to the expected operating temperature. Follow the chart below.
NOTE: While the engine is reaching the compression cycle, you may hear a "clanking" noise. This noise is causedby the impeller flails pivoting and falling into place and IS normal, This noise will continue untill the impeller reaches full speed.
An important point after buying a device Craftsman 247.77763 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Craftsman 247.77763 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Craftsman 247.77763 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Craftsman 247.77763 you will learn all the available features of the product, as well as information on its operation. The information that you get Craftsman 247.77763 will certainly help you make a decision on the purchase.
If you already are a holder of Craftsman 247.77763, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Craftsman 247.77763.
However, one of the most important roles played by the user manual is to help in solving problems with Craftsman 247.77763. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Craftsman 247.77763 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center