Instruction/ maintenance manual of the product 139.53993D Craftsman
Go to page of 76
Owner's Manual/Manual Del Propietario 1/2 HP 315Mx=GARAGE DOOR OPENER ABRIDOR DE PUERTA DE COCHERA DE 315MN= For Residential Use Only/Solo para uso residencial Model/Modelo 139.53993D I11 Z G3 I"11 cn "13 z_ o Read and follow all safety rules and operating instructions before first use of this product.
TABLE OF CONTENTS Introduction 2-7 Safety symbol and signal word review ............... 2 Preparing your garage door ....................... 3 Tools needed .................................. 3 Planning .................................... 4-5 Carton inventory .
Preparing your garage door Before you begin: • Disable locks. • Remove any ropes connected to garage door. • Complete the following test to make sure your garage door is balanced and is not sticking or binding: 1. Lift the door about halfway as shown.
Planning Identify the type and height of your garage door. Survey your garage area to see if any of the conditions below apply to your installation. Additional materials may be required. You may find it helpful to refer back to this page and the accompanying illustrations as you proceed with the installation of your opener.
Planning (Continued) ONE-PIECE DOOR INSTALLATIONS • Generally, a one-piece door does not require reinforcement. If your door is lightweight, refer to the information relating to sectional doors in Installation Step 12. • Depending on your door's construction, you may need additional mounting hardware for the door bracket (Step 12).
Carton Inventory Your garage door opener is packaged in one carton which contains the motor unit and all parts illustrated below. Accessories will depend on the model purchased. If anything is missing, carefully check the packing material. PARTS MAY BE STUCK IN THE FOAM.
Hardware Inventory Separate all hardware and group as shown below for the assembly and installation procedures. ASSEMBLY HARDWARE Metal Sleeve (2) C-Clip (2) Hex bolt 1/4-20x7/16" (14) Sprocket C.
ASSEMBLY STEP 1 Assemble the Rail To avoid installation difficulties, do not run the garage door opener until instructed to do so. 1. Open the rail carton and remove the contents onto a level work surface. Keep it clean and free of debris while you are working.
Assemble the Rail (continued) 3. Attach rail support braces to the back rail. Loosely insert 1/4-20x7/16" hex bolts into the aligned holes of the end rail and rail support brace (Figure 1). Do not finger tighten. 4. Extend the drive screw a few inches from the center rail, and slide the sleeve onto the long journal (Figure 2).
ASSEMBLY STEP 2 Fasten the Rail to the Motor Unit and Install the Trolley NOTE: To aid in assembly and installation, replace the foam packing around the motor unit. Remove it after Installation Step 4. 1. Working on a level surface, align the rail assembly with the motor unit, as shown.
ASSEMBLY STEP 3 Attach the Rail Brackets • Align rail brackets to end of rail assembly, as shown. • Insert two 1/4"-20x7/16" hex bolts. Tighten securely with a 3/8" socket. You have now finished assembling your garage door opener. Please read the following warnings before proceeding to the installation section.
INSTALLATION STEP 1 Determine the Header Bracket Location To prevent possible SERIOUS INJURY or DEATH: • Header bracket MUST be RIGIDLY fastened to structural support on header wall or ceiling, otherwise garage door might not reverse when required. DO NOTinstall header bracket over drywall.
INSTALLATION STEP 2 Install the Header Bracket You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall.
INSTALLATION STEP 3 Attach the Rail to the Header Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you'll need help. Have someone hold the opener securely on a temporary support to allow the rail to clear the spring.
INSTALLATION STEP 4 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. IMPORTANT INFORMATION ABOUT THE SAFETY REVERSING SENSOR When properly connected and aligned, the sensor will detect an obstacle in the path of its electronic beam.
INSTALLING THE BRACKETS Be sure power to the opener is disconnected. Install and align the brackets so the sensors will face each other across the garage door, with the beam no higher than 6" (15 cm) above the floor. They may be installed in one of three ways, as follows.
MOUNTING AND WIRING THE SAFETY SENSORS • Slide a 1/4"-20xl/2" carriage bolt head into the slot on each sensor. Use wing nuts to fasten sensors to brackets, with lenses pointing toward each other across the door. Be sure the lens is not obstructed by a bracket extension (Figure 5).
INSTALLATION STEP 5 Position the Opener Follow instructions which apply to your door type as illustrated. SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK A 2x4 laid flat is convenient for setting an ideal door-to- rail distance. • Remove foam packaging.
INSTALLATION STEP 6 Hang the Opener Three representative installations are shown. Yours may be different. Hanging brackets should be angled (Figure 1) to provide rigid support. On finished ceilings (Figure 2 and Figure 3), attach a sturdy metal bracket to structural supports before installing the opener.
INSTALLATION STEP 7 Install the Door Control Locate door control within sight of door, at a minimum height of 5 feet (1.52 m) where small children cannot reach, away from moving parts of door and door hardware. If installing into drywall, drill 5/32" holes and use the anchors provided.
INSTALLATION STEP 8 Electrical Requirements To avoid installation difficulties, do not run the opener until Step 11 below. To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet.
INSTALLATION STEP 10 Install the Lights • Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. • Install a 100 watt maximum light bulb in each socket.
INSTALLATION STEP 12 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following page. A horizontal reinforcement brace should be long enough to be secured to two vertical supports. A vertical reinforcement brace should cover the height of the top panel.
ONE-PIECE DOORS Please read and comply with the warnings and reinforcement instructions on the previous page. They apply to one-piece doors also. • Center the door bracket on the top of the door, in line with the header bracket as shown. Mark either the left and right, or the top and bottom holes.
INSTALLATION STEP 13 Connect Door Arm to Trolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONLY • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley.
ALL ONE-PIECE DOORS 1. Assemble the door arm, Figure 4: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • With the door closed, connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin.
ADJUSTMENT STEP 1 Adjust the Travel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. To operate the opener, press the Door Control push bar.
ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door. If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction.
ADJUSTMENT STEP 3 Test the Safety Reversal System TEST • With the door fully open, place a 1-1/2" (3.8 cm) board (or a 2x4 laid flat) on the floor, centered under the garage door. • Operate the door in the down direction. The door must reverse on striking the obstruction.
OPERATION IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of SEVERE INJURY or DEATH: 1. READAND FOLLOW ALL WARNINGS AND INSTRUCTIONS. 2. ALWAYS keep remote controls out of reach of children. NEVER permit children to operate or play with garage door control push buttons or remote controls.
Using the Wall.Mounted Door Control THE PREMIUM CONTROL CONSOLE Lighted Push Button Press the lighted push button to open I _ -_-_._ or close the door. Press again to reverse the door during the closing Light cycle or to stop the door while it's utton opening.
CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: Weather conditions may cause some minor changes in door operation requiring some re- adjustments, particularly during the first year of operation. Pages 27 and 28 refer to the limit and force adjustments.
HAVING A PROBLEM? 1. My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. • Verify the safety sensors are properly installed, aligned and free of any obstructions.
Bell Wire Safety Reversing Sensor Diagnostic Chart Safety reversing sensors wire open (broken or disconnected). OR Safety reversing sensors wire shorted or black/white wire reversed. Door control or wire shorted. Safety reversing sensors slightly misaligned (dim or flashing LED).
PROGRAMMING NOTICE: If this Security+_ garage door opener is operated with a non-rolling code transmitter, the technical measure in the receiver of the garage door opener, which provides security against code-theft devices, will be circumvented.
To Add, Reprogram or Change a Keyless Entry PIN NOTE: Your new Keyless Entry must be programmed to operate your garage door opener, USING THE "LEARN" BUTTON USING THE PREMIUM CONTROL CONSOLE.
REPAIR PARTS Rail Assembly Parts Installation Parts 3 /6 /.. ¸ 5 0 7 11 / 5 4 KEY PART NO. NO. DESCRIPTION 1 2 3 4 5 6 7 8 81C275 41A6263 12B890 12B900 41A6264 12B889 41A6262 41A4836 28A143 Rack Hardware bag (includes sprocket coupling) Left rail bracket Right rail bracket Screw drive rail assembly Complete 7' (2.
Motor Unit Assembly Parts 14 12 13 14 (Down) Brown Contact UMJT SWITCH ASSY. Contact Contact Wire KEY NO. 1 2 3 4 5 6 6a 7 PART NO. 31 C568 41 B4245 30B620 41A3150 41 D4671 41A6241 20B21-1 41 C4672 11.
ACCESSORIES 139.53702 Emergency Key Release: Required for a garage with NO access door. Enables homeowner to open garage door manually from outside by disengaging trolley. 139.53405 139.53589 8 Foot Rail Extension: To allow an 8 foot door to open fully.
CONTENIDO Introduccibn 2.7 Revision de los sfmbolos y terminos de seguridad .......... 2 Preparaci6n de la puerta de su cochera .................. 3 Herramientas necesarias .............................. 3 Planificaci6n ...............................
Preparaci6n de la puerta de su cochera Antes de comenzar: • Quite los seguros. • Retire cualquier cuerda o cable que este conectado a la puerta. • Haga la siguiente prueba con su puerta para verificar que este balanceada y que no se atore ni se pandee: 1.
Planificaci6n Identifique la aitura y el tipo de su puerta de cochera. Revise el area de su cochera y observe si aiguna de ias siguientes instalaciones corresponden a la suya.
Planificaci6n (continba) INSTALACION CON PUERTAS DE UNA SOLA PIEZA • Generalmente una puerta de una sola pieza no requiere refuerzos adicionales. Si usted tiene una puerta de material liviano y quiere reforzarla, consulte la informaci6n respecto a puertas seccionales, contenida en Instalacion, Paso 12.
Inventario de las caja de cart6n Su abridor viene empacado en una caja de cart6n que contiene el motor y las piezas que se muestran en la siguiente ilustracion.
Inventario de Piezas Antes de la instalaci6n, organice todas las piezas en grupos come se muestra en la siguiente ilustracion. TORNILLER|A Y PIEZAS PARA EL MONTAJE Pemo hexagonal de Manguito de metal .
MONTAJE PASO 1 Monte el riel No encienda ni use el abridor hasta que Ilegue al paso de la instalacion correspondiente, de otra manera corre el riesgo de complicar el proceso de instalacion. 1. Abra la caja de cart6n del carril y saque el contenido colocandolo sobre una superficie de trabajo horizontal.
Montaje el riel (continba) 3. Sujete los tirones de soporte del carril al carril trasero. Introduzca sin apretar pernos hexagonales de 1/4-20x7/16" en los agujeros alineados del carril de extremo y el tirante de soporte del carril (Figura 1). No apriete con los dedos.
MONTAJE PASO 2 Fije el riel a la unidad del motor e instale el trole NOTA: Para facilitarle el montaje y la instalacidn del motor, vuelva a colocarlo dentro del hule espuma de proteccidn, retire la espuma despu#s de concluir Instalacidn, Paso 4.
MONTAJE PASO 3 Fijacibn de las m_nsulas del riel • Proceda a alinear las mensulas en el extreme del riel, tal come se muestra en la ilustracion. • Introduzca dos tomillos de cabeza hexagonal de 1/4-20x7/16 de pulg. y tuercas de seguridad. Ajuste firmemente con una Ilave tube de 3/8 de pulg.
INSTALACION PASO 1 Determine dbnde va a instalar la M_nsula del Cabezal Para evitar una posible LESION GRAVE O INCLUSO LA MUERTE: • La m_nsula del cabezal DEBE quedar R]GIDAMENTE sujeta al soporte estructrual en la pared delantera o en el cielo raaso, de no set asi es posible que la puerta del garaje no retroceda cuando se requiera.
INSTALACION PASO 2 Instale la m_nsula del cabezal La mensula del cabezal se puede fijar a la pared sobre la puerta del garaje o en el cielo raso. Siga las instrucciones que sean mas adecuadas para las necesidades de su instalaci6n. No instale la mensula del cabezal en paneles huecos de pared.
// // // // // // // // // // Paredfrontal -- Mensula del cabezal garaje INSTALACION PASO 3 Colocacibn del riel en la m_nsula del cabezal • Coloque el abre puertas sobre el piso bajo la mensula inst.
INSTALACION PASO 4 Instale la Sistema de Protecci6n ® El sensor del sistema de retroceso de seguridad debe estar instalado y alineado correctamente, antes de que el abridor de la puerta de cochera mueva la puerta hacia abajo.
INSTALACION DE LAS MCNSULAS Aseg0rese de que el abridor no este conectado a la corriente electrica. Instale y aiinee las mensuias de manera que los sensores esten uno frente al otro en los lados opuestos de la puerta, a una distancia maxima de 15 cm (6 pulg.
MONTAJE Y CABLEADO DE LOS SENSORES DEL SISTEMA DE RETROCESO DE SEGURIDAD • Deslice la cabeza de un perno de coche de 14-20xl/2 de pulgada dentro de la ranura de los sensores. Use tuercas de mariposa para sujetar los sensores a las mensulas, con las lentes de cada sensor frente a frente a ambos lados de la puerta.
INSTALACION PASO 5 Coloque el Abridor en Posici6n Siga las instrucciones correspondientes al tipo de puerta de su garaje, como se muestra en la ilustraci6n. PUERTA SECCIONAL O PUERTA DE UNA SOLA PIEZA CON RIEL DE GUiA Puede utilizar un tirante de madera de 3.
INSTALACION, PASO 5 Cuelgue el Abridor Aquf se muestran tres ejemplos distintos para la instalacion; sin embargo, es posible que su cochera no concuerde con ningune de ellos. Las mensulas de soporte deben estar en &ngulo (Figura 1), para que proporcionen un soporte rigido.
INSTALACION PASO 7 Instale la unidad de control de la puerta Ubique el control de la puerta de manera que quede a la vista desde la puerta y a una altura minima de 1.5 m (5 pies) donde los nifios pequeffos no Io puedan alcanzar y lejos de las partes m6viles de la puerta y de la tornilleffa.
INSTALACION PASO 8 Requisitos para la instalaci6n el6ctrica Para evitar problemas con la instalacion, no opere el abre- puertas de garaje ahora. Para reducir el riesgo de electrocuci6n, el abre-puertas de garaje viene con enchufe con pata de conexion a tierra.
INSTALACION PASO 10 Instale las Luces • Oprima las lengeetas de liberacion a ambos lades de la lente. Rote la lente suavemente hacia atras y hacia abajo hasta que la bisagra quede en la posicion totalmente abierta. No quite la lente. • Instale bombillos de 100 vatios como maximo en cada portalampara.
INSTALACION, PASO 12 Fije la m_nsula de la puerta Siga las instrucciones que correspondan al tipo de puerta de cochera que usted tenga, como se muestra en la ilustraci6n o en la pagina siguiente. Si usa un puntal horizontal, este debe ser Io suficientemente largo para sujetarlo a dos soportes verticales.
PUERTAS DE UNA SOLA PIEZA Lea y respete todas las advertencias e instrucciones respecto a los refuerzos, contenidas en la pa.gina anterior, Instalacion de puertas seccionales, ya que todos los refuerzos para su puerta de una sola pieza son los mismos.
INSTALACION PASO 13 Conecte el brazo de la puerta al trole Siga las instrucciones que correspondan al tipo de puerta de cochera que usted tenga, como se muestra a continuaci6n yen la pa.gina siguiente. S(_LO PARA PUERTAS SECCIONALES • Cerciorese de que la puerta de la cochera este completamente cerrada.
TODAS LAS PUERTAS DE UNA SOLA PIEZA 1. Arme el brazo de la puerta, Figura 4: • Sujete las dos secciones de los brazes de la puerta (recto y curvo) a la mayor distancia posible, de manera que dos o t.
AJUSTES PASO 1 Ajuste el limite del recorrido HACIA ARRIBA y HACIA ABAJO AI ajustar el limite del recorrido de la puerta, se regula hasta que punto esta se detendrgt al abrir y al cerrar. Para poner en marcha el abridor, oprima el bot6n de control de la puerta.
AJUSTES PASO 2 Ajuste de la fuerza Los controles para el ajuste de la fuerza del abridor se encuentran en el panel de posterior de la unidad del motor.
AJUSTES PASO 3 Pruebe el Sistema de Retroceso de Seguridad PRUEBA • Abra completamente la puerta, coloque un pedazo de madera de 38 cm (1-1/2 de pulg) (o un pedazo de madera de 5x10 cm (2x4 pulg) ac.
OPERACION INSTRUCCIONES DE SEGURIDAD IMPORTANTES Para reducir el riesgo de LESIONES GRAVES o LA MUERTE: 1. LEA Y RESPETE TODAS LAS ADVERTENCIAS E INSTRUCCIONES.
C6mo usar la unidad de control C6mo abrir la puerta manualmente de pared LA CONSOLA DE CONTROL PREMIUM _ Bot6n " Huminado Optima el boton iluminado para abrir .
MANTENIMIENTO DE SU ABRIDOR DE PUERTA DE COCHERA AJUSTES DE L|MITE Y FUERZA: Las condiciones climatol6gicas pueden ocasionar cambios menores en la operaci6n de la puerta, los cuales van a requerir algunos reajustes, en particular durante el primer aSo de operacion.
SI TIENE ALGON PROBLEMA 1. La puerta no cierra y las luces de la unidad del motor parpadean: El sensor del sistema de retroceso de seguridad debe estar instalado y alineado correctamente para que el sistema de apertura de la puerta de la cochera se mueva en sentido descendente.
Cable Tabla de Diag El abre-puertas de garaje tiene un sistema de autodiagndstico. Cuando la luz del botdn "Aprendizaje" ("Learn") destella y luego hace una pausa, significa que puede haber un problema. Consulte la siguiente Tabla de Diagndstico.
COMO PROGRAMAR EL ABRIDOR AVI$O: Si utiliza este abre puertas de garaje Securityd_ con un transmisor no dorado de un sietema de cddigos de salto (cddigo aleatorio), se veran circunvenidas las medidae tecnicas incorporadae en el receptor del abridor para proteger contra los aparatos de captura de cddigos.
C6mo agregar, reprogramar o cambiar un c6digo de entrada sin Ilave NOTA: Su nueva Entrada sin Ilave debe programarse para que opere el abridor de la puerta de su cochera. COMO USAR EL BOTON LEARN (APRENDER) CC)MO USAR LA CONSOLA DE CONTROL PREMIUM ) 1.
ACCESORIOS 139.53702 139.53405 139.53569 Liberador de la Ilave de emergencia: Se requiere en las cocheras que NO tienen puerta de acceso. Permite al due o de la casa abrir la puerta de la cochera manualmente desde el exterior, descenectando el trole. Extension del riel de 2.
iiiiiiiiiiiiii iiiiiiiiiiiiii iiiiiiiiiiiiii iiiiiiiiiiiiii iiiiiiiiiiiiii iiiiiiiiiiiiii iiiiiiiiiiiiii iiiiiiiiiiiii_! Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no .,a,,er w.
An important point after buying a device Craftsman 139.53993D (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Craftsman 139.53993D yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Craftsman 139.53993D - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Craftsman 139.53993D you will learn all the available features of the product, as well as information on its operation. The information that you get Craftsman 139.53993D will certainly help you make a decision on the purchase.
If you already are a holder of Craftsman 139.53993D, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Craftsman 139.53993D.
However, one of the most important roles played by the user manual is to help in solving problems with Craftsman 139.53993D. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Craftsman 139.53993D along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
