Instruction/ maintenance manual of the product ENDURO-175 Cornelius
Go to page of 18
Installation Manual ICE/BEVERAGE DISPENSER MODEL: ENDURO–175 8 V AL VE IMPORT ANT : TO THE INST ALLER. It is the responsibility of the Installer to ensure that the water supply to the dispensing equipment is provided with protection against backflow by an air gap as defined in ANSI/ASME A1 12.
i 620917902INS T ABLE OF CONTENTS Page SAFETY PRECAUTIONS 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DESCRIPTION 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 620917902INS SAFETY PRECAUTIONS This ice dispenser has been specifically designed to provide protection against personal injury and eliminates contamination of ice. T o ensure continued protection and sanitation, observe the following: AL W A YS: disconnect power to the dispenser before servicing or cleaning.
2 620917902INS INST ALLA TION INSTRUCTIONS IMPORT ANT : T O THE INST ALLER. It is the responsibility of the Installer to ensure that the water supply to the dispensing equipment is provided with protection against backflow by an air gap as defined in ANSI/ASME A1 12.
3 620917902INS ICE DIVERTER KIT 02394 NOTE: For dispensing Scotsman, Wilshire, and Hoshizaki compressed ice cubes: 1. Disconnect power to dispenser . 2. Remove Merchandiser from dispenser . 3. Remove ice chute and discard gate restrictor . 4. Install ice diverter on gate mounting plate as shown below .
4 620917902INS GA TE RESTRICTOR PLA TE CAUTION: Disconnect power to dispenser before installing, removing or adjusting restrictor . ADJUSTMENT INST ALL PLA TE ON STUDS AS SHOWN FIGURE 2.
5 620917902INS FIGURE 3. MOUNTING TEMPLA TE 20 15/16 24 1/2 1 13/16 1 5/16 18 5/8 7/16 DIA. 12 9 OPENING 21 1/4 29 3/4 31 5/16 REMOV ABLE SINK 7 15/16 8 5/8 3 1/2 17 1/2 RECOMMENDED COUNTER OPENING SIZE 9” X 12” FOR UTILITIES AND BEVERAGE TUBING. OPENING CAN BE LOCA TED ANYWHERE WITHIN THE SHADED AREA.
6 620917902INS SOL VENT BOND HOSE CLAMP BARB ADAPTER 1 BARB x 3/4 MPT COUPLING 3/4 SOCKET x 3/4 FPT DRIP TRA Y DRAIN FITTING DRAIN LINE 1” I.D. PLASTIC TUBING (6 FT) WITH INSULA TION FIGURE 4.
7 620917902INS S6 INST ALL FOR NON–CARB AS REQUIRED S4 S7 CHECK VA LV E OPTIONAL FOR DIET DRINKS OR ROOT BEER S4 SYRUP T ANKS 15–50 PSIG S8 S3 S2 PRESSURE REGULA TORS S7 S5 S4 S3 S2 S1 W2 S3 W4 W3.
8 620917902INS CHECK VA LV E S5 8 S8 W A TER MANIFOLD 6 S6 SYRUP T ANKS F AUCETS VIEWED FROM FRONT OF UNIT S7 CARB WA TER S4 S3 S2 1 2 3 4 5 7 1 2 3 4 5 6 S1 S2 S3 S4 S5 S6 S1 CARB WA TER 15–50 PSIG.
9 620917902INS W ARNING: If repairs are to be made to a product system, remove quick disconnects from the applicable product tank, then relieve the system pressure before proceeding. If repairs are to be made to the CO 2 system, stop dispensing, shut off the CO 2 supply , then relieve the system pressure before proceeding.
10 620917902INS T rouble Probable Cause BEVERAGE NOT SWEET ENOUGH. A. Empty syrup tank. B. Faucet brix requires adjusting. BEVERAGES NOT COLD (UNITS WITH BUIL T -IN COLD PLA TE). A. Unit standing with no ice in hopper – no ice in cold plate cabinet.
1 1 620917902INS B L A C K B L A C K WIRING DIAGRAM TO 24V TRANSFORMER OPTIONAL KEY SWITCH MOTOR ST ART CAP ACITOR B L A C K R E D R E D BLACK WHITE W H T G R E E N BLUE RED PINK B L A C K BLACK BLACK.
12 620917902INS CAP ACITOR AGIT A TOR MOTOR GA TE SOLENOID OPTIONAL BEVERAGE TRANSFORMER MOTOR HEA TER OPTIONAL LIGHT ST ARTER BALLAST N.O. L N.C. C VEND SWITCH G N TIMER L2 L1 RECTIFIER OPTIONAL ICE LEVEL PCB BOARD OPTIONAL FLA VOR VL VS VL V SOLENOIDS KEYP AD FIGURE 8.
13 620917902INS T’ST A T LIGHT ICE LEVEL SIGNAL OPTION 1 2 DANGER! ELECTRIC SHOCK HAZARD. DISCONNECT POWER BEFORE SER VICING UNIT . SERVICE INFORMA TION GRN/ YEL TO SOLENOID MOUNTING PLA TE OPTIONAL LIGHT SOCKET W H T Y E L L O W B L A C K B L U E TO BEVERAGE P ANEL OPTIONAL LIGHT ST ARTER TO BEVERAGES F AUCET GRN/YEL GRN/YEL WHT LT .
14 620917902INS 220–240V LINE FIL TER EMI FIL TER POWER SWITCH AGIT A TOR MOTOR GA TE SOLENOID OPTIONAL BEVERAGE TRANSFORMER MOTOR HEA TER OPTIONAL LIGHT OPTIONAL ST ARTER OPTIONAL BALLAST N.
15 620917902INS W ARRANTY IMI Cornelius Inc. warrant that all equipment and parts are free from defects in material and work- manship under normal use and service. For a copy of the warranty applicable to your Cornelius prod- uct, in your country , please write, fax or telephone the IMI Cornelius office nearest you.
IMI CORNELIUS INC..
An important point after buying a device Cornelius ENDURO-175 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cornelius ENDURO-175 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cornelius ENDURO-175 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cornelius ENDURO-175 you will learn all the available features of the product, as well as information on its operation. The information that you get Cornelius ENDURO-175 will certainly help you make a decision on the purchase.
If you already are a holder of Cornelius ENDURO-175, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cornelius ENDURO-175.
However, one of the most important roles played by the user manual is to help in solving problems with Cornelius ENDURO-175. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cornelius ENDURO-175 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
