Instruction/ maintenance manual of the product 175 8 Valve Cornelius
Go to page of 10
IMPORT ANT : TO THE INST ALLER. It is the responsibility of the Installer to ensure that the water supply to the dispensing equipment is provided with protection against backflow by an air gap as defined in ANSI/ASME A1 12.1.2-1979; or an approved vacuum breaker or other such method as proved effective by test.
i 620917901 T ABLE OF CONTENTS Page MAINTENANCE 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DAIL Y (OR AS REQUIRED) 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 620917901OPR MAINTENANCE The following dispenser maintenance should be performed at the intervals indicated: DAIL Y (or as required) Remove foreign material from vending area drip tray to prevent drain blockage. WEEKL Y (or as required) Clean vending area.
2 620917901OPR C. W ash cup rest with soap solution and rinse in clean water . Install the cup rest into the drip tray . D. Clean all exterior surfaces with soap solution and rinse in clean water . 2. CLEANING INTERIOR SURF ACES CAUTION: When pouring liquid into the hopper , do not exceed the rate of 1/2 gallon per minute.
3 620917901OPR E. Using a cloth, wash down the surfaces of the cold plate and plastic cover with soap solution. F. Install and properly position the cover on the cold plate. G. Install the splash panel in the reverse order it was removed. H. Rinse cold plate surface by pouring potable water through hopper openings.
4 620917901OPR B. Sanitize syrup lines, B-I-B Systems a. Remove all the quick disconnects from all the B-I-B containers. b. Fill a suitable pail or bucket with soap solution. c. Submerge all disconnects (gas and liquid) in the soap solution and then clean them using a nylon bristle brush.
5 620917901OPR W ARNING: If repairs are to be made to a product system, remove quick disconnects from the applicable product tank, then relieve the system pressure before proceeding. If repairs are to be made to the CO 2 system, stop dispensing, shut off the CO 2 supply , then relieve the system pressure before proceeding.
6 620917901OPR T rouble Probable Cause BEVERAGES NOT SWEET ENOUGH. A. Empty syrup tank. B. Faucet brix requires adjusting. BEVERAGES NOT COLD (UNITS WITH BUIL T -IN COLD PLA TE). A. Unit standing with no ice in hopper – no ice in cold plate cabinet.
7 620917901OPR IMI CORNELIUS INC . O NE C ORNELIUS P LACE A NOKA, MN . 55303 – 6234 T ELEPHO NE (800) 238 – 3600 F ACSIMILE (800) 535 – 4231 W ARRANTY IMI Cornelius Inc. and Remcor Products Company warrant that all equipment and parts are free from defects in material and workmanship under normal use and service.
One Cornelius Place Anoka, Minnesota 55303-6234 (763) 421-6120 (800) 238-3600 Corporate Headquarters: IMI CORNELIUS INC..
An important point after buying a device Cornelius 175 8 Valve (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cornelius 175 8 Valve yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cornelius 175 8 Valve - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cornelius 175 8 Valve you will learn all the available features of the product, as well as information on its operation. The information that you get Cornelius 175 8 Valve will certainly help you make a decision on the purchase.
If you already are a holder of Cornelius 175 8 Valve, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cornelius 175 8 Valve.
However, one of the most important roles played by the user manual is to help in solving problems with Cornelius 175 8 Valve. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cornelius 175 8 Valve along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
