Instruction/ maintenance manual of the product ATCA-C110/1G AGFA
Go to page of 126
REVIE W COPY A TCA-C110/1G AMC Carrier Blade Installation and Use 225254 420 000 AA September 2005 Edition.
REVIE W COPY © Cop yright 2005 Motorola, Inc. All rights reser ved. Printe d in the United States of Ame rica. T rademarks Motorola and the styliz ed M logo are tr ademarks registered in the U .
REVIE W COPY Safety Summary The follo w ing general saf ety precautions must be obser ved during all phases of operation, ser vice, and repair of this equipment. F ailure to comply with these precautions or with specific warnings elsewhere in this manual could result in personal injur y or damage to the equipment.
REVIE W COPY Flammability All Motorola PWBs (pr inted wiring boards) are manuf actured with a fla mmability rating of 94V -0 by UL- recognized manufacturers. EMI Caution ! Caution Caution This equipme nt generates, uses and can radiate electr omagnetic ener gy .
REVIE W COPY Motorola product s with the CE marking comply with the EMC Directiv e (89/336/EEC). Complia nce with this directive implies conf or mity to the follo wing European Norms: EN55022 “Limit.
REVIE W COPY Notice While reasonab le efforts hav e been made to assure the accuracy of this document, Moto rola, Inc. assumes no liability resulting from any omission s in this document, or from the use of the inf or mation obtained therein.
REVIE W COPY ATCA-C110/1G Installation and Use Manual vii About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x vii Audience . . . . . . . . . . . . . . . . .
REVIE W COPY ATCA-C110/1G Installation and Use Manu al Contents viii Control Elem ents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Injector/Eject or Lever and Ho t Swap Switch Me chanism .
REVIE W COPY ATCA-C110/1G Installation and Use Manual ix Contents Boot Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 System Man agement . . . . . . . .
REVIE W COPY ATCA-C110/1G Installation and Use Manu al Contents x Zone 3 Conn ectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 6 Memory Map and Registers . . . . . . . . . . . . .
REVIE W COPY ATCA-C110/1G Installation and Use Manual xi Contents Manufactu rers’ Documen ts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Related Spe cifications . . . . . . . . .
REVIE W COPY.
REVIE W COPY Figure 1-1. Board Lay o ut Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Figure 1-2. Ba y Location s on A TCA-C110/1G . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REVIE W COPY.
REVIE W COPY ATCA-C110/1G Installation and Use Manual xv T able 1. Order ing Infor mation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xviii T able 2. Accessor ies Orde ring In f o r mation .
REVIE W COPY ATCA-C110/1G Installation and Use Manu al List of Table s xvi T able 6-8. I2C to G PIO’ s Device Mappings - A TMega64 -AMC Private I2C Bus . . . . . . . . . . . . . . . . 80 T able 6-9. Geo graphical addressing of AMC Bays on A TCA-C110/1G .
ATCA-C110/1G Installation and Use Manual xvii REVIE W COPY About This Manual This manua l provides bo th general and f unctional descriptions of the product along with installation and re mov al instr.
ATCA-C110/1G Installation and Use Manu al About This Manua l xviii REVIE W COPY Or der Numbers The tab le below is an e xcer pt from the b lade’ s ordering information. Ask y our local Motorola representati ve f or the current ordering inf or mation.
About This Manual ATCA-C110/1G Installation and Use Manual xix REVIE W COPY Appendix C, Thermal V alidation , pro vides inf orm ation about t hermally significant components and an o v er view of ho w to measure v ar ious junction and case temper atures.
ATCA-C110/1G Installation and Use Manu al About This Manua l xx REVIE W COPY Miscellaneous notations The term AMC Carrier refer s to the A TCA-C 110/1G board/b lade, and is used interchang eably . The phrases Service Processor and MPC8540 are used interchangeab ly .
About This Manual ATCA-C110/1G Installation and Use Manual xxi REVIE W COPY Use ESD Wrist Strap Befor e you install or remo ve a board Motor ola str ongly recommends that y ou use an antistatic wrist strap and a conductive f oam pad.
ATCA-C110/1G Installation and Use Manu al About This Manua l xxii REVIE W COPY MA C Mediu m Access Controller (for Ethernet) MII Media Independent Interface (f or Eth ernet) MIIM Media Independent Int.
1 ATCA-C110/1G Installation and Use Manual 1 REVIE W COPY 1 A TCA- C110/1G Baseboard Preparation and Installation Intr oduction This chapter outlines star tup and s af ety inst r uctions, hardware acce ssories details, s w itch settings , hardwar e preparation, installation and remo val instructions.
ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 2 REVIE W COPY ■ Onboard De vices such as: – PCI to PCI-Express Bridge – GigE PHYs – .
Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 3 REVIE W COPY Baseboar d Lay out The figure belo w shows the placement of the components on the A TCA- C110/1G board. Equipment Required T o install the A TCA- C110/1G board y ou need the f ollowing equipment: ■ PICMG 3.
ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 4 REVIE W COPY The A TCA- C110/1G has t wo f ace plates: top and b ottom, which are moun ted on the top strut and bottom strut, resp ectiv ely .
Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 5 REVIE W COPY Getting Star ted This section pro vides an ov er view of the step s necessar y to install the A TCA- C110/1G and a brief section on unpac king and ESD precautions .
ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 6 REVIE W COPY Caution Caution A void touc hing areas of integrated circuitry; st atic dischar ge can damage circuits.
Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 7 REVIE W COPY Har dware Upgrades and Accessories Hardware upgrades an d accessories allow an easy and cost -efficient wa y to adapt the system board to y our application needs.
ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 8 REVIE W COPY Step 3: After rem oving the carrier board from its card slot, place it on a clean and adequately pr otected working surface (preferably an ESD mat) with the bottom side of the board facing up.
Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 9 REVIE W COPY SO-DIMM Installation in a Non-P owered System Note ■ The SO-DIMM onboard the A TCA-C110/1 G can be installed only when th e module is remov ed from the carrier board.
ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 10 REVIE W COPY Step 3: Firmly insert th e SO-DIMM into the socket at a 45° angle in the direction as indicat ed in Figure 1-6 . Push the SO-DIM M down until th e retaining clip o f the socket loc ks the SO-DIM M into position.
Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 11 REVIE W COPY Removing SO-DIMM T o remov e the SO-DIMM from the SO-DIMM sock et on the A TCA- .
ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 12 REVIE W COPY Installing an AMC Module in a P owered System T o install an AMC Module on a Adv ancedTCA host board, ref er to the Figure 1-10 on page 13 , read all cautions and w ar nings and perf or m the f ollowing steps .
Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 13 REVIE W COPY Step 2: Identify the AMC bay to be used for ins ta llation.
ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 14 REVIE W COPY Remo ving an AMC Module from a P o wered System T o remov e an AMC Module from the A TCA- C110/1G, read all cautio ns and warnings and perf or m the f ollowing steps .
Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 15 REVIE W COPY Rear T ransition Modules At the time of writing this manual the A CC/AR TM-C110 Rear T ransition Module w as av ailable f or the blade.
ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 16 REVIE W COPY Switch Settings The b lade pro vides the configur ation s witch SW1. The s witch pro vides AMC ba y selection in the JT AG cha in.
Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 17 REVIE W COPY Observe ESD Precautions Use ESD Wrist Strap ESD Motor ola str ongly reco mmends that y ou use an antistatic wrist strap and a conductive foa m pad when installing or up grading a syste m.
ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 18 REVIE W COPY Understand Hot Swap ! Caution Caution Boar d/Component Damage Inserting or removing non-hot swap car ds or transiti on modules wi th pow er applied may res ult in damage to module components.
Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 19 REVIE W COPY Note The hot-swap s witch contacts should be in the OFF position (high- resistance) whe n the board handle s are fully inserted.
ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 20 REVIE W COPY Note The A TCA- C110/1G is designed to ope rate as an Adv ancedTCA node board. Ref er to V er ify Slot Usage on p age 19 f o r more details.
Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 21 REVIE W COPY Note If a Rear T ransition Module (R TM) is already installed in the same slot, be careful not to bend an y pins of the R TM connectors.
ATCA-C110/1G Installation and Use Manu al Chapter 1 ATCA-C110 /1G Baseboard Pre paration and I nstallation 22 REVIE W COPY Step 1: Remove face pl ate cables and cables from th e AMC, if applicable.
Chapter 1 ATCA-C110/1G Baseboard Preparat ion and Installation ATCA-C110/1G Installation and Use Manual 23 REVIE W COPY Y ou may access the stand ard serial console por t via the AR TM-C110. This ser ial por t serves as the U-Boot and oper ating system (OS) console por t.
REVIE W COPY.
2 ATCA-C110/1G Installation and Use Manual 25 REVIE W COPY 2 Operating Instructions This chapter contains the follo wing information: ■ System Initialization ■ Hot Swap Suppor t on page 26 ■ Boo.
ATCA-C110/1G Installation and Use Manu al Chapter 2 Op erating Instruct ions 26 REVIE W COPY ■ Bef o re the system is po wered up ensure th at chassis pow er supply v oltage settings matches th e voltage present in cou ntr y of use (if the power supply in your syst em is not auto-sensin g).
Chapter 2 Op erating Instruct ions ATCA-C110/1G Installation and Use Manual 27 REVIE W COPY Deb ug Suppor t The deb ug mechanisms supported on A TCA- C 110/1G include: ■ Debug connectors f or IPMC A serial interface f or debug will be provid ed f or each A TMega controller .
REVIE W COPY.
3 ATCA-C110/1G Installation and Use Manual 29 REVIE W COPY 3 U-Boot Fir mw are Ov er vie w U-Boot is a softw are package ba sed on an open-source boo t loader f or embedded systems utilizing P owerPC , MIPS, or ARM Processors. U-Boot can be inst alled in a boot R OM and used as a boot loader to do wnload and activat e application code.
ATCA-C110/1G Installation and Use Manu al Chapter 3 U-Bo ot Firmware Over view 30 REVIE W COPY # default: off # description: The tftp server serves files using the trivial file transfer # protocol.
Chapter 3 U-Boot Firmwar e Overview ATCA-C110/1G Installation and Use Manual 31 REVIE W COPY Using this configuration, the DHCP ser v er will reply to a request from the target with the Ethernet address 00:30:BF :01:02:D0 , pro vided the f ollowing conditions are sa tisfied: ■ The target is locate d in the subnet 1 0.
ATCA-C110/1G Installation and Use Manu al Chapter 3 U-Bo ot Firmware Over view 32 REVIE W COPY Initial Steps In the def ault configuration , U-Boot operates in an int eractiv e mode providing a simple.
Chapter 3 U-Boot Firmwar e Overview ATCA-C110/1G Installation and Use Manual 33 REVIE W COPY sleep - delay execution for some time tftpboot- boot image via network using TFTP protocol and env variable.
REVIE W COPY.
4 ATCA-C110/1G Installation and Use Manual 35 REVIE W COPY 4 Functional Descr iption This chapter describes the functional co ncepts of the A TCA- C110/1G as well as the main ph ysical and electr ical structure of the board. A TCA- C110/1G Overview The f ollowing tabl e lists the f eatures of the A TCA-C 110/1G.
ATCA-C110/1G Installation and Use Manu al Chapter 4 Function al Description 36 REVIE W COPY A TCA Compliant features The A TCA- C110/1G complies with the f ollowing f eatures as per the PICMG 3.
Chapter 4 Functional Description ATCA-C110/1G Installation and Use Manual 37 REVIE W COPY Bloc k Diagram – A TCA- C110/1G The A TCA- C110/1G server b lade is divided into se ver al functional b locks, see Figure 4-1 .
ATCA-C110/1G Installation and Use Manu al Chapter 4 Function al Description 38 REVIE W COPY Pr ocessor and Processor interfaces CPU A TCA-C 110/1G has MPC854 0 as a Ser vice Processor working with the.
Chapter 4 Functional Description ATCA-C110/1G Installation and Use Manual 39 REVIE W COPY ■ Deliv ering interr upts to the CPU for servicing All the interrupts gener ated on the A TCA-C110 are wired to the interrupt controller of th e MPC8540 Pro cessor .
ATCA-C110/1G Installation and Use Manu al Chapter 4 Function al Description 40 REVIE W COPY PCI/PCI-X Interface The MPC8540 pro vides PCI/PCI-X interf ace that complies with the PCI Local Bus Specification, Re v . 2.2 and the PCI-X Addendum to the PCI Local Bus Specification, Rev .
Chapter 4 Functional Description ATCA-C110/1G Installation and Use Manual 41 REVIE W COPY System Management The A TCA-C110 carries an Intelligent Platf orm Management Controller (IPMC) entity . The IPMC is a chassis management entity on individ ual cards that monitor v oltages, temperat ure, and chassis characteristics.
ATCA-C110/1G Installation and Use Manu al Chapter 4 Function al Description 42 REVIE W COPY ■ T elecom Clock Interf ace Control ■ Digital IO The IPMI module co nsists of three micro- controllers fro m Atmel. The interf ace of each of the controllers is illustrated below in Figure 4-3 on page 42 .
Chapter 4 Functional Description ATCA-C110/1G Installation and Use Manual 43 REVIE W COPY Private I 2 C Bus There are tw o private I 2 C busses implemented on the IPMI Module of A TCA- C110/1G. The busses are Master-only I 2 C b usses implemented on the Sla ve micro-controllers .
ATCA-C110/1G Installation and Use Manu al Chapter 4 Function al Description 44 REVIE W COPY Digital IO The IPMI interf ace of the A TCA- C110/1G helps in the configur ation and oper ations of the board through its GPIO pins. Ref er to Digital IO on pa ge 73 f or more details about t he GPIO pin signals.
Chapter 4 Functional Description ATCA-C110/1G Installation and Use Manual 45 REVIE W COPY PCI-Express Switch The 16-lane PCI-Expre ss s witch is used as the PCI-Express s witching element on the F abric Interf ace Module of A TCA-C110.
ATCA-C110/1G Installation and Use Manu al Chapter 4 Function al Description 46 REVIE W COPY PCI-Express to PCI Bridge The PCI-to-PCI- Express Bridge acts as the in terf ace between the FIM (through its PCI -Express interf ace) and the Processor of the A TCA-C110.
Chapter 4 Functional Description ATCA-C110/1G Installation and Use Manual 47 REVIE W COPY I/O Subsystems Onboard De vices The f ollowing onboard de vices are present on A TCA-C110/1G ■ User Flash ■ AMC Ba ys ■ Progr ammable Logic Device s – CPLD User Flash The A TCA- C110/1G suppor ts upto 128 MB User Flash.
ATCA-C110/1G Installation and Use Manu al Chapter 4 Function al Description 48 REVIE W COPY Power-on Sequence The pow er-on sequence is contr olled by the CPLD onb oard the A TCA- C110/1G.
Chapter 4 Functional Description ATCA-C110/1G Installation and Use Manual 49 REVIE W COPY Serial A T A interface The Ser ial A T A (SA T A) interface is a high-s peed ser ialized storage inter f ac e.
ATCA-C110/1G Installation and Use Manu al Chapter 4 Function al Description 50 REVIE W COPY I 2 C Bus There are tw o I 2 C interf aces on the A TCA-C110/1G . ■ The Private I 2 C b uses from the IPMI Controllers ■ The I 2 C interf ace from the MPC8540 The private I 2 C Address Map f or MPC8540 is shown in T able 6-4 on pa ge 74 .
5 ATCA-C110/1G Installation and Use Manual 51 REVIE W COPY 5 Controls , Indicators and Connector Pin Assignments This chapter pro vides details of cont rols, indicato r s as well as connector pin assignments f or all connectors on th e A TCA-C 110/1G board.
ATCA-C110/1G Installation and Use Manu al Chapter 5 Control s, Indicators and Connector Pin Assignments 52 REVIE W COPY Baseboar d Connectors The f ollowing sections describe the onboard connectors on A TCA- C110/1G base board. Figure 5-2 show s the location of the connect ors.
Chapter 5 Control s, Indicators and Connector Pin Assignments ATCA-C110/1G Installation and Use Manual 53 REVIE W COPY FIM Connectors The FIM connecto rs used on the baseboa rd are specially designed f or high-speed dif f erential signaling. T ab le 5-2 sho ws the f abr ic signals routed between the baseboard and FIM throu gh the connecto r .
ATCA-C110/1G Installation and Use Manu al Chapter 5 Control s, Indicators and Connector Pin Assignments 54 REVIE W COPY The f our FIM connectors: J1, J2, J3 and J4, onboard the A TCA-C110 /1G are described below . See Figure 5-2 on page 52 f or location of FIM co nnectors.
Chapter 5 Control s, Indicators and Connector Pin Assignments ATCA-C110/1G Installation and Use Manual 55 REVIE W COPY AMC4_SA T A0_TX+ S4+ 7 43 S22+ AMC4_PCIEXP_LANE1_ TX+ AMC4_SA T A0_TX- S4- 8 44 S.
ATCA-C110/1G Installation and Use Manu al Chapter 5 Control s, Indicators and Connector Pin Assignments 56 REVIE W COPY T able 5-4. FIM Connector J2 Pinout Signal Pin Name Pin # Pin # Pin Name Signal .
Chapter 5 Control s, Indicators and Connector Pin Assignments ATCA-C110/1G Installation and Use Manual 57 REVIE W COPY AMC2_PCIEXP_LANE0_TX+ S17+ 33 69 S35+ PROC_GBE_POR T1_TX+ AMC2_PCIEXP_LANE0_TX- S.
ATCA-C110/1G Installation and Use Manu al Chapter 5 Control s, Indicators and Connector Pin Assignments 58 REVIE W COPY F ABRIC_LINK5_RX- S13- 26 62 S31- PEX_8114_PCIe_LANE1_TX- F ABRIC_LINK5_TX+ S14+.
Chapter 5 Control s, Indicators and Connector Pin Assignments ATCA-C110/1G Installation and Use Manual 59 REVIE W COPY AMC Connectors The AMC modules are connected to the carrier boa rd via the AMC connectors . See Figure 5-2 on page 52 f or AMC connector locat ions.
ATCA-C110/1G Installation and Use Manu al Chapter 5 Control s, Indicators and Connector Pin Assignments 60 REVIE W COPY Clocks The telecom synchroniza tion cloc ks from LCCB interf ace are routed to the AMC boards . The option f or the AMC Module to driv e the CLK3 to the A TCA backplane is pro vided for t he AMC Ba y3 and AMC Bay4.
Chapter 5 Control s, Indicators and Connector Pin Assignments ATCA-C110/1G Installation and Use Manual 61 REVIE W COPY The SA T A por ts are mapped to the P ort 2 and P or t 3 of the AMC connect or as per the AMC .3 Specification . The ports from each of the AMC Ba ys are routed to the F abric Interf ace Module.
ATCA-C110/1G Installation and Use Manu al Chapter 5 Control s, Indicators and Connector Pin Assignments 62 REVIE W COPY A TCA Backplane Connector s The A TCA backplane conn ectors reside in the th ree zones 1 to 3 as specif ied by the A TCA standard and are called J10 , J20 to J23 and J30 to J31.
Chapter 5 Control s, Indicators and Connector Pin Assignments ATCA-C110/1G Installation and Use Manual 63 REVIE W COPY Zone 1 Connectors The connector residing in Zon e 1 is called J10 (see Figu re 5-.
ATCA-C110/1G Installation and Use Manu al Chapter 5 Control s, Indicators and Connector Pin Assignments 64 REVIE W COPY Zone 2 Connectors Zone 2 contains f our connectors: J20, J2 1, J22 and J23 (see .
Chapter 5 Control s, Indicators and Connector Pin Assignments ATCA-C110/1G Installation and Use Manual 65 REVIE W COPY T able 5-12. Zone 2 Bac kplane Connect or J21 Pinout - Rows A to D Pin # ABCD 1 R.
ATCA-C110/1G Installation and Use Manu al Chapter 5 Control s, Indicators and Connector Pin Assignments 66 REVIE W COPY 7 Reserved Reser ved T er minated T er mina ted 8 Reserved Reser ved T er minated T er mina ted 9 Reserved Reser ved T er minated T er mina ted 10 Reser ved Reserved T er minated T er minated T able 5-15.
Chapter 5 Control s, Indicators and Connector Pin Assignments ATCA-C110/1G Installation and Use Manual 67 REVIE W COPY Zone 3 Connectors Zone 3 contains thre e connectors: J30, J31, and J32 ( see Figure 5-3 on page 62 ).
ATCA-C110/1G Installation and Use Manu al Chapter 5 Control s, Indicators and Connector Pin Assignments 68 REVIE W COPY T able 5-19. Zone 3 Bac kplane Connect or J30 Pinout - Rows E to H Pin # E F G H.
Chapter 5 Control s, Indicators and Connector Pin Assignments ATCA-C110/1G Installation and Use Manual 69 REVIE W COPY 7 XA UI_LANE2_RX+ XA UI_LANE2_RX- XA UI_LANE3 _RX+ XA UI_LANE3_RX- 8 Reser ved Reser ved Reser ved Reser ved 9 Reser ved Reser ved Reser ved Reser ved 10 Reser ved Reser v ed XAUI_MDC XA UI_MDIO T able 5-21.
REVIE W COPY.
6 ATCA-C110/1G Installation and Use Manual 71 REVIE W COPY 6 Memor y Map and Registers This chapter describes the f ollowing mapping inf or mation f or the A TCA- C110/1G board: ■ Memory Maps on pag.
ATCA-C110/1G Installation and Use Manu al Chapter 6 Me mory Map and Regis ters 72 REVIE W COPY Interrupt Mapping All the interrupts gener ated on the A TCA-C110/1 G are wired to the inter rupt controller of the MPC8540 Pro cessor .
Chapter 6 Memory Map and Registers ATCA-C110/1G Installation and Use Manual 73 REVIE W COPY Shelf Management Registers (IPMI interface) F or details abou t accessing the IPMC via IPMI co mmands as wel.
ATCA-C110/1G Installation and Use Manu al Chapter 6 Me mory Map and Regis ters 74 REVIE W COPY I 2 C Address Map f or MPC8540 The de vices suppor ted by the Processo r MPC8540 I 2 C interf ace along with their I 2 C addresses are shown in T able 6-4 .
Chapter 6 Memory Map and Registers ATCA-C110/1G Installation and Use Manual 75 REVIE W COPY T emperature Sensor Board T empe rature Sensor , LM75CIM 0x9E FIM Devices BIB - EEPR OM for F abric Interf ace Module Board Inf or mation Block EE PROM 0xAE I 2 C to GPIO De vice HotPlug control PCA9557PW 0x32 I 2 C ADC Onboard ADC, AD7997 0x41 T able 6-5.
ATCA-C110/1G Installation and Use Manu al Chapter 6 Me mory Map and Regis ters 76 REVIE W COPY T elecom CLK1 Buffer Enable Signals (Address: 0x38) 0 A TCA_CLK1A_EN Enables the Cloc k to be sourced to .
Chapter 6 Memory Map and Registers ATCA-C110/1G Installation and Use Manual 77 REVIE W COPY T elecom CLK2 Buffer Enable Signals (Address: 0x3A) 0 A TCA_CLK2A_EN Enables the Cloc k to be sourced to the.
ATCA-C110/1G Installation and Use Manu al Chapter 6 Me mory Map and Regis ters 78 REVIE W COPY The A Tmega64-AMC micr o-controller Priv ate I 2 C interf ace is used f or the control of the AMC Ba ys and the R TM.
Chapter 6 Memory Map and Registers ATCA-C110/1G Installation and Use Manual 79 REVIE W COPY T able 6-7. Priv ate I 2 C Address Map - A Tmega64- AMC micro-contr oller Device Device description Address .
ATCA-C110/1G Installation and Use Manu al Chapter 6 Me mory Map and Regis ters 80 REVIE W COPY I 2 C to GPIO’ s Device Mappings - A TMega64-AMC Private I 2 C Bus T able 6-8.
Chapter 6 Memory Map and Registers ATCA-C110/1G Installation and Use Manual 81 REVIE W COPY R TM Control Signals 0R T M _ I M P B _ R D Y The IPMB isolator has completed the star t-up after enabling t.
ATCA-C110/1G Installation and Use Manu al Chapter 6 Me mory Map and Regis ters 82 REVIE W COPY GPIO Geographical addressing of AMC Ba ys on A TCA- C110/1G Geogr aphical Addressing f or AMC Bays U : Un.
A ATCA-C110/1G Installation and Use Manual 83 REVIE W COPY A T roub leshooting Err or List This appendix pro vides a hint list for detectin g erroneous system configu rations and an y untow ard or unusual beha vior of the A TCA-C110/1G. It cannot repla ce a serious and sophisticated pre- and post-sales suppo r t during application de velopment.
ATCA-C110/1G Installation and Use Manu al Appendix A Tro ubleshooting 84 REVIE W COPY During or After Sy stem Initialization Prob lem P o ssible Reason Solution The blue hot-s wap LED does not glow after inser ting the board. The board has no t mated completely with the backplane conne ctors.
Appendix A Troubleshooting ATCA-C110/1G Installation and Use Manual 85 REVIE W COPY During Boot-up Pr ocedure Prob lem P ossible Reason Solution The board seems to hav e powered up , but there are no boot-up prints on the console OR the boot-up prints halt mid wa y .
ATCA-C110/1G Installation and Use Manu al Appendix A Tro ubleshooting 86 REVIE W COPY During Boar d Operation Prob lem P ossible Reason Solution Board runs unstable or hangs after some duration of operation. Disregard of environmental requirements 1: Check that internal system temperature remains within specifi ed ranges f or all system de vices.
Appendix A Troubleshooting ATCA-C110/1G Installation and Use Manual 87 REVIE W COPY RT M gets reset. Super capacitor is drained if the board has not been powered on f or a sufficient duration (more than 8 hours). P ower on the board and reconfigure th e R TM.
REVIE W COPY.
B ATCA-C110/1G Installation and Use Manual 89 REVIE W COPY B Specifications Specifications This appendix provides general mechanical, environmental and electrical specifications for the ATCA-C110/1G. En vironmental and Ph ysical Specifications The A TCA- C110/1G f eatures the industr y-standard A TCA form fa ctor .
ATCA-C110/1G Installation and Use Manu al Appendix B Spec ifications 90 REVIE W COPY T able B-1. A TCA- C110/1G En vironmental Specifications Characteristics Specifications En vironmental Parameter s A minimum of 300 LFM (linear feet per minute) of forced air cooling is recommended for operation in the higher temperature ranges.
Appendix B Specificatio ns ATCA-C110/1G Installation and Use Manual 91 REVIE W COPY P o wer Requirements The b lade’ s pow er requirements depe nd on the installed hard ware accessories . If y ou want to install accessories on the board, the load of th e respectiv e accessor y has to be added to that of the b lade.
ATCA-C110/1G Installation and Use Manu al Appendix B Spec ifications 92 REVIE W COPY Standar d Compliance The A TCA-C110/1G is CE appro ve d and meets the f ollowing standard req uirements: Note The A TCA-C110/1G is yet to be qua lified in the following standards .
Appendix B Specificatio ns ATCA-C110/1G Installation and Use Manual 93 REVIE W COPY EMC Compliance The A TCA- C110/1G was tested in an EM C-compliant chassi s and meets the requiremen ts f or EN55022 Class A equipment.
REVIE W COPY.
C ATCA-C110/1G Installation and Use Manual 95 REVIE W COPY C Ther mal V alidation Thermal Requirements Board component temp eratures are aff ected b y ambient temperat ure, airflo w , board electrical operat ion and softw are operation .
ATCA-C110/1G Installation and Use Manu al Appendix C Thermal Validation 96 REVIE W COPY Component T emperature Measurement The f ollowing sections outline gener al temperat ure measurement method s. F or the specific types of measur ements required f or thermal ev aluation of this board, see T able C-1 on page 95 .
Appendix C Thermal Validatio n ATCA-C110/1G Installation and Use Manual 97 REVIE W COPY If components are cov ered by mechanical par ts such as heatsinks, y ou will need to machine these par ts to route t he ther mocouple wir e. Mak e sure that the ther mocoup le junction cont acts only the electrical component.
ATCA-C110/1G Installation and Use Manu al Appendix C Thermal Validation 98 REVIE W COPY Measuring Local Air T emperature Measure local component ambient temper ature b y placing the thermocouple downstr eam of the compo nent. This meth od is conser v ative since it includes heating of th e air by the component.
D ATCA-C110/1G Installation and Use Manual 99 REVIE W COPY D Related Documentation Embedded Comm unication s Computing Documents The Motorola pu blications listed below are ref erenc ed in this man ual.
ATCA-C110/1G Installation and Use Manu al Appendix D Re lated Document ation 100 REVIE W COPY Manufacturer s’ Documents F or additional inf ormation, refer to the f ollowing table f or manuf acturers’ data shee ts or user’ s manuals . As an additional help , a source f or the listed document is pro vided.
Appendix D Related Document ation ATCA-C110/1G Installation and Use Manual 101 REVIE W COPY Related Specifications F or additional inf or mation, ref er to the f ollowing table fo r related specifications . As an additional help , a source f or the listed document is pro vided.
REVIE W COPY.
REVIE W COPY ATCA-C110/1G Installation and Use Manual 103 A AMC bay locations . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ATCA-C110/1G block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 37 main functional blocks . . . . . . .
REVIE W COPY.
An important point after buying a device AGFA ATCA-C110/1G (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought AGFA ATCA-C110/1G yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data AGFA ATCA-C110/1G - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, AGFA ATCA-C110/1G you will learn all the available features of the product, as well as information on its operation. The information that you get AGFA ATCA-C110/1G will certainly help you make a decision on the purchase.
If you already are a holder of AGFA ATCA-C110/1G, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime AGFA ATCA-C110/1G.
However, one of the most important roles played by the user manual is to help in solving problems with AGFA ATCA-C110/1G. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device AGFA ATCA-C110/1G along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
