Instruction/ maintenance manual of the product CSI-300 Code Alarm
Go to page of 12
128- 1 OF 12 Model CSI-300 Owner ’s Manual 4 Button Remote Security System with Dual Stage Shock Sensor IMPORT ANT ! In order to provide the highest possible level of security to your vehicle, this system is equipped with selectable manual override circuitry .
128- 2 OF 12 Page 2 YOUR “ Code Hopping “ TRANSMITTERS The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current automotive security system.
128- 3 OF 12 Page 3 SILENT ARMING - ACTIVE 1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid. 2. Press and hold the Lock button on the keychain transmitter for 2 seconds. ; Dash mounted LED begins to flash slowly .
128- 4 OF 12 Page 4 ; Whenever the system is armed, the dash mounted LED indicator will slowly flash. This serves as a visual deterrent to the potential thief. The LED is a very low current bulb and will not cause the vehicle’s battery to drain, even when left unattended for extended periods.
128- 5 OF 12 Page 5 SILENT DISARMING 1. As you approach the vehicle, press and hold the Unlock button on the keychain transmitter for 2 seconds. ; Dash mounted LED turns off. If passive arming was selected during the installation, then the LED will start flashing rapidly , indicating that the system is rearming automatically .
128- 6 OF 12 Page 6 p If the LED is flashing three times...pause...three times...pause...etc., then an intrusion attempt was made through one of the vehicle’s doors. These intrusion warning indicators are stored in the system’s memory and will only be erased when the ignition key is turned on.
128- 7 OF 12 Page 7 1 . Disarm the system by use of the transmitter , or by use of the emergency override sequence. Turn the ignition switch to the on position. 2. Within 10 seconds, press and release the valet/override switch, 3 times. 3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.
128- 8 OF 12 Page 8 NOTE: If after step 8, the LED flashes a code other than what was just entered, this indicates that the code has not been changed. Y ou will have to repeat steps 1 through 7 above being certain to note the following: Acceptable digits 10ths or units are 1 through 9.
128- 9 OF 12 during the Panic sounding period. 3. During the panic mode, the Lock and Unlock buttons can be used to lock and unlock the doors, (if the option is installed), however once the unlock/disarm button is pressed, the vehicle's starter inhibit device, (where installed) will be disabled allowing the vehicle to start.
128- 10 OF 12 Page 10 Check with your installation center for more information on the optional accessory that may have been installed and how it is accessed, as the transmitter buttons must be programmed to access this option if installed.
128- 11 OF 12 CSI-300 SYSTEM FUNCTIONS A T A GLANCE DASH LED INDICA TORS RAPID FLASHING = P ASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = V ALET MODE 3 FLASH.
128- 12 OF 12 © 2003 Audiovox Electronic Corporation, 150 Marcus Blvd., Hauppauge, N.Y. 11788 128-6802 Page 12.
An important point after buying a device Code Alarm CSI-300 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Code Alarm CSI-300 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Code Alarm CSI-300 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Code Alarm CSI-300 you will learn all the available features of the product, as well as information on its operation. The information that you get Code Alarm CSI-300 will certainly help you make a decision on the purchase.
If you already are a holder of Code Alarm CSI-300, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Code Alarm CSI-300.
However, one of the most important roles played by the user manual is to help in solving problems with Code Alarm CSI-300. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Code Alarm CSI-300 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
