Instruction/ maintenance manual of the product CSI-200 Code Alarm
Go to page of 8
128- 1 of 8 3 Button Remote Security System with Stage Shock Sensor & Starter Disable Model CSI-200 Owner ’s Manual FEA TURES : 2 Four Button Code Hopping RF Transmitters Four Channel Co.
128- 2 of 8 NOTE: Y our system has the option of using a siren, the vehicle horn, or both for the sounding device. Where the siren is referenced below , the horn or both may in fact chirp, or beep. ARMING THE SYSTEM - ACTIVE 1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid.
128- 3 of 8 Page 3 PROTECTION WHILE THE SYSTEM IS ARMED ; Opening any protected door , hood, or trunk lid will cause the alarm to immediately sound. The alarm will continue to sound for 30 seconds, then stop and continue to monitor all protected entry points.
128- 4 of 8 Page 4 button is activated, the drivers door only will unlock, pressing the unlock button a second time will cause all doors to unlock. 1. As you approach the vehicle, press and hold the unlock button on the keychain transmit- ter for 2 seconds.
128- 5 of 8 Page 5 valet mode, all alarm functions are bypassed, however the remote panic feature and remote door locks will remain operational. T o use the valet mode, the system must first be disarmed either by using your keychain transmitter , or by operating the manual override sequence.
128- 6 of 8 NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then 5 seconds during any of the above steps, the unit will revert back to the last successfully stored code. Custom Code Programming Example: T o Change the code from the factory preassigned code of 1 1 to “52” you would do the following: 1.
128- 7 of 8 1. Turn the ignition key on then off. 2. Within 10 seconds, press and release the valet push button switch three times. 3. If the chirps were on before you started, then you will hear 2 chirps indicating they have been turned off.
128- 8 of 8 © Code Systems Inc. 525 Minnesota Drive. Troy MI 48083 128- CSI-200 SYSTEM FUNCTIONS A T A GLANCE DASH LED INDICA TORS RAPID FLASHING = P ASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = V ALET MODE 3 FLASH...P AUSE = INTRUSION ZONE 3 2 FLASH.
An important point after buying a device Code Alarm CSI-200 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Code Alarm CSI-200 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Code Alarm CSI-200 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Code Alarm CSI-200 you will learn all the available features of the product, as well as information on its operation. The information that you get Code Alarm CSI-200 will certainly help you make a decision on the purchase.
If you already are a holder of Code Alarm CSI-200, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Code Alarm CSI-200.
However, one of the most important roles played by the user manual is to help in solving problems with Code Alarm CSI-200. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Code Alarm CSI-200 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
