Instruction/ maintenance manual of the product PRO100 AeroGarden
Go to page of 16
KEEP THIS GUIDE! Si m ple S t e p s T o G e t Y o u r U p a n d G r o w i n g Q u i c k S ta rt Gu i d e C O N G R AT U L AT I O N S On y our pur chase o f the A eroG ard en PR O 10 0 ! With this beau.
1 IMPOR T ANT SAFETY INSTRUCTIONS (SA VE THESE INS TRUCTIONS) W hen using this Aer oGarden PRO 100 electrical furnishing, basic precautions should al w ays be follo wed, including the following: Read all instructions before using this A eroGarden furnishing.
Master Gardener B Insert Lamp Arm into Base Push straight in. 2 Instructions C ontinued On Next P age Plug Lamp Cor d into Lamp Hood D Insert Gr ow Bulbs into Lamp Hood C Lamp Cord Lamp Hood (bottom view) DO NO T TWIST BULBS! Remember to replace Gr ow Bulbs e very 6 months.
3 Use one hand to grasp Lamp Arm . Gently slide AeroGarden tow ard the surface edge and place other hand under Base . Mo ving Y our Aer oGarden PRO 100 G 1 Quic k Start Assembly (continued ) Check to be sur e that Bowl is securel y in place. NEED ADDITIONAL HELP? F or supplies and information, visit… www .
Wonderful Stuff 4 A w a y F rom Reac h of children and pets Direct sources of heat (e.g., sto ve, furnace v ents) Direct sources of cold air (e.g., windo w drafts, A/C v ents) F or Optimal T ending & Harv esting, Also Consider Easy access to un-softened w ater Note: Do not place beneath under-cabinet lights.
5 Plant Y our Gar den B Insert Seed Pods into Gro w Surface openings. Check to see that… • Seed P ods are in the same position on Grow Surface as they were in Seed Kit T ra y . • Seed P od Labels are facing forward. • Seed P ods are pressed firmly in place.
6 Add Starting Nutrient T ablets and Record Planting Date D Note: Do not remo ve Bio-Domes until seeds hav e sprouted. NEVER REMO VE SEED POD LABELS . Place a Bio-Dome on each Seed P od . Press Bio-Dome down until its rim almost touches Gro w Surface .
7 3 Starting Y our Gar den Plug Cor d into Electrical Outlet A A green light next to “Germination” and a white light on C ontrol P anel will illuminate. Grow Bulbs will come on. L ook under Lamp Hood to check that both bulbs are lit. If not , chec k to see if: • Grow Bulbs are properly inserted in L amp Hood (page 2, step 1 C).
8 Y our Light T imer C • Y our lights will sta y on for about 1 6 hours and will shut off for about 8 hours. * • Y our lights will come on ev ery day at the time y ou plugged in your AeroGarden PRO 100 .* * Except when using “24-Hour Light ” setting, which sets lights to be on for 24 hours.
P ersonalize Y our Light T imer (optional) Y our PRO 100 has lights and a built-in timer that automatically provide plants with the optimal amount of “sunlight” (about 1 6 hours) and “night” (about 8 hours), depending on the plant type you selected in the previous section.
Select Germination The “ 2 4 -Hou r L ig ht” set ti n g al l ow s y ou to o ve rri de the bu i l t -i n l i ght t ime r and k eep l i gh t s on a nd pu mp ru nn i ng 2 4 hou rs a da y .
• W ater Lo w When light blinks add water up to “F ill T o Here. ” • Add Nutri ent (F eed Garden - Basic Feeding) When “ Add Nutrient” and “W ater Low” lights start blinking (ev ery 2 weeks), add 2 nutrient tablets* and fill the Bowl with w ater up to “F ill to Here.
Bas i c R emi n de rs Abo ut Y ou r A er oG a rd en (continued) Raise L amp Hood (Lights) As pl an ts grow t o 1 - 2” from li ghts , ra i se Lamp Ar m one Loc kin g Bu t t on at a ti me . Be s ure Lam p Arm i s set on th e lowe st L ocki ng But ton wh en starti ng y ou r AeroG ar den PR O 10 0 .
Pr epar e F or Y our Next Gar den 13 C le an in g Ins tr ucti ons f or y our A er oGa rde n Use only water and mild soap w hen cleaning your AeroGarden (except w hen Sanitizing - Step 7). Do not use abrasi ve cleaners or run through the dishwasher . Whe n y our g arde n has co mple ted i t’ s gro wi ng cy cl e … Sanitize AeroGarden.
Reset Add Nutrient If y ou hav e alread y gro wn a garden in y our Aer oGarden PRO 1 00 , please follo w the instructions below to r eset the nutrient timer: Pr epar e F or Y our Next Gar den (continued) 14 Replanting Y our AeroGar den ! Bundle cord when furnishing is not in use.
U.S. CA UTION – Y ou are cautioned that any changes or modications not expressly approved in this manual could void your authority to operate this equipment. NO TE: T his equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to P art 1 5 of the FCC Rules.
An important point after buying a device AeroGarden PRO100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought AeroGarden PRO100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data AeroGarden PRO100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, AeroGarden PRO100 you will learn all the available features of the product, as well as information on its operation. The information that you get AeroGarden PRO100 will certainly help you make a decision on the purchase.
If you already are a holder of AeroGarden PRO100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime AeroGarden PRO100.
However, one of the most important roles played by the user manual is to help in solving problems with AeroGarden PRO100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device AeroGarden PRO100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
