Instruction/ maintenance manual of the product GL-X CMA Dishmachines
Go to page of 19
MODEL GL-X INSTALLATION & OPERATION Rev. 1.01 800-854-6417 FAX 714 - 8 95 - 2 141 Owner’s Manual Keep with machine for reference CMA DISHMACHINES 12700 KNOTT AVENUE GARDEN GROVE, CALIFORNIA 92841 www.
T ABLE OF C ONTENTS M ODEL CMA-GL-X 1. SPECIFICAT IONS ......................................................................................... 2 1.1. GL-X ..............................................................................................
1. S pecifications METRIC EQUIVALENT 1.1. GL-X WATER CONSUMPTION PER RACK 1.7 GAL. 6.44 L PER HOUR 40.8 GAL. 154.4 L OPERATING CYCLE WASH TIME-SEC 57 57 RINSE TIME-SEC 48 48 DWELL TIME-SEC 15 15 TOTAL CYCLE 2 MIN. 2 MIN. OPERATING CAPACITY RACKS PER HOUR 30 30 WASH TANK CAPACITY 1.
1.2. GL-X Operational Cycle The GL-X Operational Cycle has a total cycle time of 2 m inutes (120 seconds). The Timing Diagram and the steps listed below de tail the individual functions that are executed during each Operational Cycle.
The pump motor runs the pump for the 57-s econd wash cycle, then pumps the water out through the drain, turns off for about 8 seco nds (allowing the machine to refill with clean rinse water) and then runs the pump for the 48-second rinse cycle. 3. Cam switch 3 controls the drain function.
Getting Started 2. Getting S t arted 2.1. Introduction to the GL-X The GL-X Glasswasher is unique in its field; it has all the features of a standa rd commercial size machine packed into an under-cou nter, standalone glasswasher. Operation of the GL-X is extremely easy.
Getting Started 2.2. Receiving and Installation The glasswasher is shippe d from the factory in a corru gated box on a wooden pallet. The installation guidelines give a systematic pro cedure for setting up the machine. 1. Start by removing the box and packaging mate rial.
Getting Started 2.2.4. Installers Checklist Glasswasher checked for concealed damage Hot water supply is recommended 140° F (60 C) Incoming water supply line is ½” minimum Supply c.
Operation 3. Operation 3.1. Initial Setup 3.1.1. Check… Drain screen is in place Spay arms and end plugs are secure 3.1.2. Chemicals • Assure there is a sufficient supply of chemicals before beginning a shift.
Operation These cams were set at the factory but must be adj usted after final installation to maximize efficien cy of chemical use ( se e section 4.1.1 Cam Adjus tment .) 3.2.3. Proper Filling The number 4 cam determi nes the am ount the mach ine is automatically filled each cy cle.
Maintenance 4. Maintenance The maintenance proced ures detail ed in this sect ion are to be performed by quali fied personnel. 4.1. Timer assembly The standard timer assem bly con sists of a (2 minutes per revolution) moto r turning a common shaft, which, in turn, rotates eight cams.
Maintenance 4.2. Quick service guide MODELS: GLX TECHNICA L ISSUE CAUSE SOLUTION Delim er s w it ch in d e lim e po s it ion Flip t o NORMAL position Wash Pump motor will not shut off Faulty delimer switch Replace switch, P/N 00475.30 Faulty manual drain switch Replace switch, P/N 03406.
Maintenance 4.3. Troubleshooting PROBLEM LIKELY CAUSE SOLUTION Power off at circuit breaker Reset circuit breaker Defective power swit ch Replace power switch P/N: 00433.10 Machine inoperative Defective timer assembly motor Replace timer assembly motor P/N: 00501.
Maintenance PROBLEM LIKELY CAUSE SOLUTION Turn up supply water heate r Low incoming water temperature (below 140° F) Insulate supply water pipe Thermostat out of adjustment Adjust thermostat Low heat during operation Defective sustainer heater Replace heat er P/N: 04109.
Maintenance PROBLEM LIKELY CAUSE SOLUTION Defective sani/detergent primer switch Replace primer switch P/N: 03470.00 Activating detergent primer switch does not run pum p Defective detergent pump motor Replace pump motor P/N: 00416.00 Defective sani/detergent primer switch Replace primer switch P/N: 03470.
Addendum 5. Addendum for Machines Installed in the City of Chicago “All food dispensing e stablishments using chlorine o r other approved chemical sanitizers shall, at all times, maintain an adequate testing devi ce.
Appendix A: Operator & Cleaning Instructions MODEL GL-X INSTALLATION & OPERATION MANUAL Rev. 1.01 –08/04/05 PAGE 16.
Electrical Diagram 6. Electrical Diag ram 1 1 / 2 0 / 0 6 W A T E R S O L E N O I D V A L V E P U M P M O T O R D E T S A N I R I N S E D R A I N S A N I P R I M E R R I N S E P R I M E R R e v .
Electrical Diagram J 7 J 6 J 5 W A S H T A N K I N D I C A T O R T E M P E R A T U R E S E N S O R W I R E D I A G R A M F O R M O D E L : G L - X 0 9 / 0 6 / 0 5 D E L I M E N O R M A L D O O R S A F E T Y S W I T C H C Y C L E L I G H T P O W E R L I G H T R e v .
An important point after buying a device CMA Dishmachines GL-X (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought CMA Dishmachines GL-X yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data CMA Dishmachines GL-X - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, CMA Dishmachines GL-X you will learn all the available features of the product, as well as information on its operation. The information that you get CMA Dishmachines GL-X will certainly help you make a decision on the purchase.
If you already are a holder of CMA Dishmachines GL-X, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime CMA Dishmachines GL-X.
However, one of the most important roles played by the user manual is to help in solving problems with CMA Dishmachines GL-X. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device CMA Dishmachines GL-X along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
