Instruction/ maintenance manual of the product SDX 11500 Citrix Systems
Go to page of 14
Citrix NetScaler 10 Quick Start Guide: SDX 1 1500/13500/14500/16500/18500/20500 Platform Citrix NetScaler 10.
Copyright and T rademark Notice Copyright © 2013 Citrix Systems, Inc. All rights reserved. NO P AR T OF THIS DOCUMENT MA Y BE REPRODUCED OR TRANSMITTED IN ANY FORM OR BY ANY MEANS OR USED TO MAKE DERIV A TIVE WORK (SUCH AS TRANSLA TION, TRANSFORMA TION, OR ADAPT A TION) WITHOUT THE EXPRESS WRITTEN PERMISSION OF CITRIX SYSTEMS, INC.
Quick Installation and Configuration W elcome to the Citrix NetScaler Application Delivery product line. Please review the following information before proceeding with installation of the SDX appliance.
Figure 1-1. Citrix NetScaler SDX 11500/13500/14500/16500/18500/20500 appliance, front panel The following figure shows the back panel of the SDX 11500/13500/14500/16500/18500/20500 appliance.
w R oot password: The root user (nsroot) has full administrative privileges on the appliance. The root password is used to authenticate the root user . The default root password is nsroot. Y ou can change this password during initial configuration of the appliance.
w Allow the power supply units and hard drives to cool before touching them. w Install the equipment near an electrical outlet for easy access. w Mount equipment in a rack with sufficient airflow for safe operation.
Connecting a NetScaler SDX Appliance to the Network Connect the interfaces on the appliance to the network ports on the appropriate switches by using Ethernet/fiber optic cables. Figure 1-4. Connecting a Citrix NetScaler SDX appliance to the network W arning: Connecting multiple network ports to the same switch or VLAN can result in a network loop.
Note: Electrical Safety Precautions Caution: During installation or maintenance procedures, wear a grounding wrist strap to avoid ESD damage to the electronics of the appliance. Use a conductive wrist strap attached to a good earth ground or to the appliance.
Initial Configuration through the Management Service User Interface T o set up the appliance by using the Management Service user interface, connect a workstation or laptop to the same network as the appliance. T o configure the NetScaler SDX appliance by using the Management Service user interface 1.
Note: After changing the network configuration, close all browser instances and open a new browser instance to access the appliance. Initial Configuration through the Serial Console T o perform initial configuration of the SDX appliance from outside the L2 domain, connect to the console port of the appliance and follow the instructions carefully .
Changing the Password of the Default User Account The default user account provides complete access to all features of the Citrix NetScaler SDX appliance. Therefore, to preserve security , the nsroot account should be used only when necessary , and only individuals whose duties require full access should know the password for the nsroot account.
4. In the P assword box, type nsroot . 5. In the Configur ation tab, click Network and type values for the following parameters: • IP Address—IP address of the LOM port. • Subnet Mask—Subnet mask used to define the subnet of the LOM port. • Default Gateway—IP address of the router that connects the LOM port to the network.
Specifications SDX 11500/13500/14500/16500/18500/205 00 Number of power supplies 2 AC power supply input voltage, frequency , and current 100-240 V AC 50-60 Hz 6.5-3.5 A Maximum power consumption 650 W Heat dissipation 2200 BTU per hour W eight 46 lbs Height 2U Width EIA 310-D for 19-inch racks Depth 28 in or 71.
2. Click the Documentation tab. 3. T o view a short description of each document, hover your cursor over the title. T o open a document, click the title. T o contact Citrix Support, call 1-800-4-CITRIX (1-800-424-8749), or log on to MyCitrix at http://www .
An important point after buying a device Citrix Systems SDX 11500 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Citrix Systems SDX 11500 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Citrix Systems SDX 11500 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Citrix Systems SDX 11500 you will learn all the available features of the product, as well as information on its operation. The information that you get Citrix Systems SDX 11500 will certainly help you make a decision on the purchase.
If you already are a holder of Citrix Systems SDX 11500, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Citrix Systems SDX 11500.
However, one of the most important roles played by the user manual is to help in solving problems with Citrix Systems SDX 11500. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Citrix Systems SDX 11500 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
