Instruction/ maintenance manual of the product SF302-08PP Cisco Systems
Go to page of 16
Quick Start Guide Cisco 300 Series Managed Switches.
2 Cisco 300 Series Managed Switches W elc ome Thank you f or choosing the Cisco 300 S eries Managed Switch, a Cisco network c ommunications device. This device is de signed to be operational right out of the box as a standard bridge. In the def ault configuration, it will f or ward pack ets betwe en connecting devic es after power up.
Cisco 300 Series Managed Switches 3 Do not deploy the device in a location where any of the f ollowing conditions exist: • High Ambient T emperature —Ref er to the f ollowing table f or the high ambient temperatur e rating of each switch: • Reduc e d Air Flow —Both side panels must be unob structed t o prev ent overheating.
4 Cisco 300 Series Managed Switches Rack -Mount Plac ement S TEP 1 Remove the f our screws fr om each side near the front of the swit ch. Retain the screws f or re-installation. (Do not r emove the f our screws from each side near the back of the swit ch.
Cisco 300 Series Managed Switches 5 There is a wall-mount kit pack e d with your swit ch. The dimensions f or the mount kit are as f ollows: Mount the managed switch t o the wall by drilling two pilot hole s 3.7 inches (95 mm ) apar t , at taching the provided anchors and screws t o the wall, then sliding the switch int o p osition on the screws.
6 Cisco 300 Series Managed Switches S TEP 3 Repeat Step 1 and Step 2 f or each devic e you want t o connect to the managed switch. N OTE Cisco strongly recommends using Cat5 or better cable f or Gigabit connectivity . When you connect your network devic es , do not e x ceed the maximum cabling distance of 100 meters (328 f eet) .
Cisco 300 Series Managed Switches 7 N OTE The switch can deliv er a maximum of 15.4 W at ts to an y 10/ 100 or Gigabit PoE port . The 24MP , 28MP , 52P and 52MP models of the swit ch can deliver a maximum of 30 W atts to any P oE p or t . W ARNING The switch is t o b e connected only to P oE networks without routing t o the outside plant .
8 Cisco 300 Series Managed Switches C onfiguring the Cis c o 300 S erie s Manage d S witch B efore Y ou B e gin V erify the managing c omputer r equirements in the pr o duct release not es .
Cisco 300 Series Managed Switches 9 N OTE Details on how to change the IP addr es s on your computer depend upon the t ype of architectur e and operating system you ar e using. Use the computer Help and Suppor t functionalit y to sear ch f or “IP Addressing.
10 Cisco 300 Series Managed Switches • 8 data bits • no parity • 1 stop bit • no flow control S TEP 4 Enter a user name and password. User names and pas swords ar e both case s ensitive and alpha-numeric. The default username is cisco, and the default pas sword is cisco.
Cisco 300 Series Managed Switches 11 Pinging 192.168.1.254 with 32 bytes of data: Reply from 192.168.1.254: bytes=32 time<1ms TTL=128 If you cannot r each the switch, y ou should get a reply similar t o the f ollowing : Pinging 192.168.1.254 with 32 bytes of data: Request timed out.
12 Cisco 300 Series Managed Switches Fe a tures of the Cis c o 300 S erie s Man age d Switch This section de scribe s the exterior of the managed swit ches including por ts , LEDs , and connections . F ront Panel Port s The por ts and LEDs are located on the front panel of the swit ch.
Cisco 300 Series Managed Switches 13 • The LEDs of the corresponding RJ-45 p or t light to r e spond to the SFP interface traffic. N OTE SG300 - 10SFP and S G300 -28S FP have dedicat ed S FP por ts . Their LED status and indication are the same as on the RJ-45 por ts.
14 Cisco 300 Series Managed Switches Console— The Console p or t is where y ou can connect a s erial cable to a computers serial por t f or configuration using a terminal emulation pr ogram.
Cisco 300 Series Managed Switches 15 Where to Go F rom Here Suppor t Cisco Supp or t Communit y w w w .cis co.com/ go/smallbizsupport Cisco Supp or t and Reso ur ces w w w .cisco.c om/ go/ smallbizhelp Phone Suppor t Contacts ww w .cisc o.com/ en/US/ suppor t / tsd_cisc o_small_busines s _suppor t_center_contacts .
Americas He adquar ters Cisco Systems, Inc. w w w .cisco.c om Cisco has more than 200 offic es worldwide. Addresse s, phone numbers , and fax numbers are list ed on the Cisco web site at w w w .cisco.c om/ go/ of fice s . Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.
An important point after buying a device Cisco Systems SF302-08PP (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Systems SF302-08PP yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Systems SF302-08PP - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Systems SF302-08PP you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Systems SF302-08PP will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Systems SF302-08PP, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Systems SF302-08PP.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Systems SF302-08PP. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Systems SF302-08PP along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
