Instruction/ maintenance manual of the product OL-31386-01 Cisco Systems
Go to page of 42
G ETTING S TARTED G UIDE Cisco Aironet 2700 Series Access Points 1 About this Guide 2 Introduction to the Access Point 3 Safety Instructi ons 4 Unpacking 5 Configuratio ns 6 Access Point Ports and Con.
2 OL-31386-01 Last Updated: March 31, 2015.
3 1 About this Guide This Guide provides in structions on how to inst all and configure your Cisco Aironet 2700 Series Access Point. This guide also provides mounting in structions and limited troubleshooting procedures. The 2700 Series Access Point is referred to as the access point in this document.
4 – Management Frame Protection (MFP) – Throughput, forwarding, and filtering performan ce scaled to meet 3 spatial stream, 1.3-Gbps data-rates • 64 MB flas h size • 802.11af/at – CDP (Cisco Discovery Protocol) • 2.4 GHz and 5 GHz 802.11n radios with the following features: – 4TX x 4RX for 5 GHz and 3Tx x 4Rx for 2.
5 War n in g Installation of the equipme nt must comply with local and national electric al codes. Statement 1074 War n in g This product relies on the building’ s installation for short-circ uit (overcurrent) protection. Ensure tha t the protective device is rated not greater than: 20A.
6 4 Unpacking T o unpack the access point , follow these steps: Step 1 Unpack and remove the acce ss point and the accessory kit from the shipping box. Step 2 Return any pa cking material to the shippi n g container and save it for future use. Step 3 V erify that you have received the items listed be low .
7 • AIR-ANT2524DW -R • AIR-ANT2524DG-R • AIR-ANT2524V4C-R • AIR-ANT2544V4M-R • AIR-ANT2566P4W -R Internal Antennas The 2702I model access point is configured with four dual-band inverted-F antennas, and two 2.
8 6 Access Point Ports and Connectors The 2702E model access point has external antenna co nnectors and the LED indictor on th e top of the model, as shown in Figure 1 .
9 Figur e 2 Access P oint LED Indi cator (t op)— 2702I Model The ports and connections on the bottom of the access point are shown in Figure 3 . 1 Dual-band antenna connector A 3 Dual-band antenna c.
10 Figur e 3 Access P oint P or ts and Connection s (bot t om)-AIR2702E and 2702I Models 1 Kensington lock slot 4 Auxiliary Ethernet Port 2 DC Power connection port 5 RS232 Console Port 3 Primary Ethe.
11 Note The Auxiliary Ethernet port is disabled. Do not connect this port to a PoE switch. Connecting the primary and auxiliary ports to a PoE sw itch will not provide additional power . 7 Configuring the Access Point This section describes how to connect the access point to a wireless LAN controller .
12 Note Y ou cannot edit or query any ac ce ss point using the controller CLI i f the name of the access point contains a space. Note Make sure that the controller is set to the curren t time.
13 • Access point mounting options: below a suspended ceiling, on a fla t horizontal surface, or on a desktop. Note Y ou can mount the access point above a su spended ceiling but you must purcha se additional mounting ha rdware: See “Mounting th e Access Po int” sec tion on pag e 16 for additional information.
14 Pre-Installation Configuration Setup The pre-installation configuration setup is shown in Figure 4 . Figure 4 Pr e-Installation Configuration Setup T o perform pre-installati on configuration, perform the following steps: Step 1 Make sure that the Cisco wireless LAN controller DS port is connected to the network.
15 e. CAPW AP UDP ports must not be blocked in the network. f. The access point must be able to find the IP address of the controller . This can be accomplished using DHCP , DNS, or IP subnet broadcast. This guide describes the DHCP method to convey the controller IP addres s.
16 Step 5 If your access point does not indicate norma l operation, turn it off and repeat the pre-installation configuration. Note When you are installing a La yer 3 access point on a different subne.
17 c. If the LED blinks sequentially for more than 5 minutes, the access point is unable to find its primary , secondary , and tertiary Cisco wir eless LAN controller.
18 Using DHCP Option 43 Y ou can use DHCP Option 43 to provide a list of c ontroller IP addresses to the access points, enabling them to find and jo in a controller . F o r additional information, refer to the “Configuring DHCP Option 43 and DHCP Option 60” section on pag e 39 .
19 Operatin g status Blinking blue Software upgrade in progr ess Cycling through green, red, and off Discovery/join process in progress Rapidly cycling through blue, green, and red Access point locati.
20 Troubleshooting the Ac cess Point Join Process Note The controller must be running Cisco IOS Software Release 7.6.12 0.x or later to support 2700 series access points. A detailed explanation of th e join process is on Cisco.com at the following URL: http://www.
21 • An existing access point run ning software release 7.6.120.x or late r has been reset after clearing the configuration. If any of these conditions are met and the access point has n ot yet joined a controller , y ou can also configure a DHCP server to return a sys log server IP address to the access point using opti on 7 on the server .
22 11 Declarations of Conformity and Regulatory Information This section provides declarations of conformity and regulatory information for the Cisco Aironet 2700 Series Access Points.
23 This device operates in the 5150-5250MHz and 54 70-5725MH z bands and is therefore restricted to indoor operation only per FCC guidance. This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules.
24 VCCI Statement for Japan War n in g This is a Class B product based on the standard of the V oluntary Control Council for Interf erence from Informatio n T echnology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference.
25 Guidelines for Operating Cisco Aironet Access Points in Japan This section provides guidelines for avoiding interf erence when operating Cisc o Aironet access points in Japan.
26 Statement 371—Power Cable and AC Adapter English Translation When installing th e product, please use the provided or designated connection cables/power cables/AC adaptors.
27 This device complies with Class B Limits of Industry Canada. Operatio n is subject to the follo wing two conditions: 1. This device may not cause harmful interferenc e, and 2. This device must accept any interference received, incl uding interference that may cause undesired operation.
28 Afin de réduire le risque d'interférence aux au tres utilisateurs, le typ e d'antenne et son gain doivent être choisis de façon à ce que la puissance isotrope r ayonnée équivalente (p.i .r .e.) ne soit pas supérieure au niveau requis pour obtenir une communication satisfaisante.
29 Declaration of Conformity with regard to the R&TTE Directive 1999/5/EC & Medical Directive 93/42/EEC.
30 The following standards were applied: EMC—EN 301.489-1 v1.8.1; EN 301.489-17 v2.1.1 Health & Safety—EN60950-1: 2005; EN 50385: 2002 Radio—EN 300 328 v 1.7.1; EN 301.893 v 1.5.1 The conformity assessment procedure ref erred to in Article 10.
31 This device also conforms to the EMC requirem ents of the Medical Devices Directi ve 93/42/EEC. Note This equipment is intended to be used in a ll EU and EFT A countries. Outdoor u se may be restricted to certain frequencie s and/or may require a license fo r operation.
32 As such the systems are desi gned to be operated as to avoid contact with the antennas by the end user . It is recommended to set the system in a location where the antennas can remain at least a m.
33 This Device Meets the In dustry Canada Guidelines for Exposure to Radio Waves The 2700 series device includes a radio transmi tter an d receiver . It is designed not to exceed the limits for exposure to radio waves (radio frequency electrom agnetic fields) as referenced in Heal th Canada Safety Code 6.
Santé Canada affirme que la littérature scientifiq ue actuelle n'indique pas qu'il faille prendre des précautions particulières lors de l'utilisation d'un appareil sans fil.
35 Administrative Rules for Cisco Ai ronet Access Points in Taiwan This section provides administrative rules for oper ating Cisco Aironet access points in T aiwan.
36 English Translation Administrative Rules for Low- power Radio-Frequency Devices Article 12 For those low-power radio-frequenc y devices that have alr eady recei ved a type-a pproval , compani es, business units or users should not change its freque ncies, increase its power or change its original features and functions.
37 English Translation Low-power Radio-frequency Devices T echnical Specifica tions Operation of Cisco Aironet Access Points in Brazil This section contains special information for oper ation of Cisco Aironet access points in Brazil.
38 Figur e 5 Br azil Regulat ory Inf or mation Portuguese Translation Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e nã o po de causar interferência a sistemas operando em caráter primário.
12 Configuring DHCP Option 43 and DHCP Option 60 This section contains a DHCP Option 43 configu ration example on a Windows 2003 Enterprise DHCP server for use with Cisco Aironet lightweig ht acce ss points. For other DHCP server implementations, consult product documentation for configuring DHCP Option 43.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliate s in the U.S. and other countries. T o view a list of Cisco trademarks, go to this URL: www.cisco .com/go/trademarks . Third-party trad emarks mentio ned are the p roperty of t heir respec tive owners.
41.
42.
An important point after buying a device Cisco Systems OL-31386-01 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Systems OL-31386-01 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Systems OL-31386-01 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Systems OL-31386-01 you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Systems OL-31386-01 will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Systems OL-31386-01, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Systems OL-31386-01.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Systems OL-31386-01. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Systems OL-31386-01 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center