Instruction/ maintenance manual of the product IE 3000 Cisco Systems
Go to page of 32
1 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide • About This Guide, page 1 • T aking Out Wh at Y ou Need, page 2 • Connecting Expansion Modul .
Cisco IE 3000 Switch Getting Started Guide 2 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 For additi onal installatio n and conf iguration i nformation for Cisco IE 30 00 switches, see the Cisco IE 3000 docume ntation on Cisco.
3 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Figure 1 Cisco IE 30 0 0 Shipping Bo x Contents Connecting Expansion Modules The switch can operate as a standalone device with Fast Ethernet ports.
Cisco IE 3000 Switch Getting Started Guide 4 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Follo w these steps to connect the e xpansion modules to the switch. Step 1 Remov e the right side panel b y firmly grasping both sides in th e middle and pulling it outward.
5 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Running Express Setup When you f i rst set up the switch, yo u should use Express Setup to ent e r the initial IP information. Doing this enabl es the switch to connect t o local routers and th e Internet.
Cisco IE 3000 Switch Getting Started Guide 6 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 T o run Express Setup: Step 1 Make sure that nothing is con n ected to the switch. During Express Setup, the switch acts as a DHCP server . If your PC has a static IP address, change your PC settings befo re you begin to temporarily use DHCP .
7 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Step 6 Connect a Cat egory 5 Ethernet cabl e (not provid ed) from the blinking switch port to th e Ethernet port on your PC. The port LEDs on your PC and the swi tch blink green wh ile the sw itch configures the connection.
Cisco IE 3000 Switch Getting Started Guide 8 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Step 9 Enter the netw ork settings. All ent ries must be in English letter s and Arabic numbers. • Management Interface (VLAN ) : W e recommend using the def ault, VLAN 1 .
9 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Refreshing the PC IP Address After you complete Express Setup, you sho u ld refresh the PC IP address: • For a dynamically assigned IP address, disconnect th e PC from the switch, and reconnect the PC to the netwo rk.
Cisco IE 3000 Switch Getting Started Guide 10 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 3. Use the de vice manager to perform basic switch configur ation and monitoring.
11 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Using the Switch Console Port: Follo w these steps: 1. Connect the supplied RJ- 45-to-DB-9 ad apter cable (conso le cable) to the standard 9-pin serial port on the PC.
Cisco IE 3000 Switch Getting Started Guide 12 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 • Attaching the Po wer and Relay Connector , page 20 • Optional Procedures, page 21 Equipment T.
13 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide • Airflo w around the switch and throu g h the v ents is unrestricted. T o prev ent the switch from overheating, thes e must be the minimum clearances: – T op and bottom: 4.
Cisco IE 3000 Switch Getting Started Guide 14 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 War ni ng This unit is intend ed for installation in restricted acc ess areas. A restricted access area can be ac cessed only through the use of a special tool, lock and key , or other means of security .
15 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide War ni ng When used in a Class I, Division 2, haza rdous location, this equipment must be mounted i.
Cisco IE 3000 Switch Getting Started Guide 16 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Mounting the Switch to a DIN Rail or to the Rack Adapter Follo w these steps to mount the switch on a DIN r a il or in a rack. Step 1 If you are mountin g th e s witch in a rack, first secure the Cisco IE 3000 rack adapter to the ra ck.
17 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Grounding the Switch Follo w these steps to connect the switch to a protectiv e ground. War ni ng This equipment must be grounded. Never defeat t he ground conductor or operate the equipment in the absence of a suitably installed ground conductor .
Cisco IE 3000 Switch Getting Started Guide 18 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Wiring the DC Power Source Follo w these steps to prepare the DC power cable. War ni ng Before performing any of the following procedures, ensure that power is removed from the DC circ uit.
19 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide War ni ng This product relies on the building’ s installation for short-circuit (overcurrent ) protection. Ensure that the protective device is rated not greater tha n: 5A.
Cisco IE 3000 Switch Getting Started Guide 20 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Attaching the Power and Relay Connector Follo w these steps to connect the DC po wer and relay conn.
21 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Optional Procedures For detailed inst ructions on these proc edures, see the Cisco IE 3000 Switch H a rd w a re I n s t a l l a t i o n G u i d e on Cisco.
Cisco IE 3000 Switch Getting Started Guide 22 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Connecting to 10/100 and 10/100/1000 Ports Follo w these steps: For simpli fied cabling, the automatic medium-dependent interf ace crossover (auto-MDIX) feature is en abled by default on the swit ch.
23 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Installing SFP Modules and Connecting to Ports Follo w these steps: For a list of su pported modules, see the release not es on Cisco.
Cisco IE 3000 Switch Getting Started Guide 24 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Connecting to Dual-Purpose Ports Only one port on a dual -purpose port can be acti ve at a time. If b oth ports are connected, the SFP modu le port has priority .
25 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide In Case of Difficulty See these sections if you ha ve dif ficulty setting up your swit ch: • T ro.
Cisco IE 3000 Switch Getting Started Guide 26 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Resetting the Switch Follo w these steps to return your switch to the factory default settings.
27 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Accessing Online Help First look for a soluti on to your problem in th e troubleshooting section of the switch hardware i nstallation guide or the switch softw are configuration guid e on Cisco.
Cisco IE 3000 Switch Getting Started Guide 28 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Obtaining Documentation and Submitting a Service Request For informatio n on obtaining documentatio.
29 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide Note Y ou must have Adobe Acrobat R eader to view and print PDF files. Y ou can do wnload the reader from Adobe’ s website: http://www .adobe.com 3.
Cisco IE 3000 Switch Getting Started Guide 30 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 To Receive a Return Materials Authorization (RMA) Number Contact the compan y from whom you purc hased the product. If you purchased the product directly from Cisco, contact your Cisco Sales and Service Representativ e.
31 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 Cisco IE 3000 Switch Getting Started Guide.
Cisco IE 3000 Switch Getting Started Guide 32 Cisco IE 3000 Switch Getting Started Guide OL-16234-01 CCDE, CCENT, Cisco Eos , Cisco Lumin, Cisco StadiumVision, the Ci sco logo, DCE, and Welcome to the.
An important point after buying a device Cisco Systems IE 3000 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Systems IE 3000 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Systems IE 3000 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Systems IE 3000 you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Systems IE 3000 will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Systems IE 3000, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Systems IE 3000.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Systems IE 3000. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Systems IE 3000 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
