Instruction/ maintenance manual of the product ASR 903 Cisco Systems
Go to page of 132
Cisco Systems, Inc. www.cisco.com Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco we bsite at www.
THE SPECIFICATION S AND INFORMAT ION REGARDING THE PRODUCTS IN THIS MA NUAL ARE SUBJ ECT TO CHANGE WITHOUT NOT ICE. ALL STATEMENTS , INFORMATION , AND RECOMMEN DATIONS I N THIS MANUA L ARE BELIEVE D TO BE ACCURATE BUT ARE PRESENTED WI THOUT WARRANTY OF ANY KIND, EX PRESS OR IMPLIED.
iii Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 CONTENTS About this Book ix Document Revision History ix Document Audience x Document Organization x Document Conventions x Obtaining .
Contents iv Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Serial Number Label Location 1-20 Interface Numbering 1-20 Regulatory Compliance 1-21 CHAPTER 2 Preparing for Installation 2-1 .
Contents v Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Installing the Router in a Rack 3-1 Installing the Chassis Brackets 3-2 Installing the Router Chassis in the Rack 3-3 Installing.
Contents vi Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Uninstalling the Cisco Microsoft Windows USB Drive r 3-35 Connecting to the Au xiliary Port 3-36 Connecting a Manage ment Ether.
Contents vii Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Console/ Aux RJ45 RS23 2 Serial Port Pino ut 5-3 T1/E1 Port Pinout 5-4 Serial Cable Pinouts 5-5 Management Ethernet Po rt Pino.
Contents viii Cisco ASR 903 Router Hardware Installation Guide OL-25178-05.
-ix Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 About this Book The preface descri bes the re vision history , audience, or ganization, and co n v entions of Ci sco ASR 903 R o u t e r H a rd w a re I n s t a l l a t i o n G u i d e .
-x Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter Document Audience This guide is intended for users wh o are responsible for instal ling the Cisco ASR 903 Series Aggre gation Services Router .
-xi Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter Note Means reader take note . Ti p Means the following info rmation will help you sol v e a pr oblem . Caution Means reader be car efu l . In this situation, you might perf orm an action that could result in equi pment damage or loss of data.
-xii Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter.
CH A P T E R 1-1 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 1 Cisco ASR 903 router Overview T h e C i s c oA S R9 0 3r o u t e r i s a f u l l y -featured aggregation platform de signed for the cost-ef fecti ve deli very of con verged mo bile and b usiness services.
1-2 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 1 Cisc o ASR 903 router Overview Cisco ASR 903 router Features • Side-to-side forc ed air cool ing • T emperature range of .
1-3 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 1 Cisco ASR 903 router Overview Cisco ASR 903 router Features Power Supply Features The Cisco ASR 903 router support A C and DC po wer supplies.
1-4 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 1 Cisc o ASR 903 router Overview Cisco ASR 903 router Features Redundancy The Cisco ASR 903 router chassis includes a slot for an optional redundant po wer supply .
1-5 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 1 Cisco ASR 903 router Overview Cisco ASR 903 router Features Figure 1 -2 DC PEM Module (A90 0-PWR550-D) with Euro-style Conne.
1-6 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 1 Cisc o ASR 903 router Overview Cisco ASR 903 router Features AC Power Specifications Fan Tray The fan tray modules supported .
1-7 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 1 Cisco ASR 903 router Overview Cisco ASR 903 router Features Fan Tray (A903-FAN) The Cisco ASR 903 router uses a modular f an tray that is separate from the po wer supply .
1-8 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 1 Cisc o ASR 903 router Overview Cisco ASR 903 router Features Figur e 1 -5 Cisco ASR 903 F an T ra y with Du st Filter and Dum.
1-9 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 1 Cisco ASR 903 router Overview Cisco ASR 903 router Features The air plenum is av ailable from GA W ( www .GawT echnology . net ). T o order an air plenum, contact the Sales and Marketing support staf f at GA W (see Ta b l e 6 - 2 ).
1-10 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 1 Cisc o ASR 903 router Overview Cisco ASR 903 router Features Supported RSP Features The RSP provides the f ollowing features.
1-11 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 1 Cisco ASR 903 router Overview Cisco ASR 903 router Features Figur e 1 -6 RSP Inte rf aces Summary For more inf ormation about installin g the RSP , see “RSP Installa tion” sectio n on page 3-1 3 .
1-12 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 1 Cisc o ASR 903 router Overview Cisco ASR 903 router Features Gigabit Ethernet SF P Interface Module The Gigabit Ethernet Small For m-Factor Pluggable ( SFP) interface module pro vides eight Gigabit Ethernet SFP modules.
1-13 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 1 Cisco ASR 903 router Overview Cisco ASR 903 router Features • SFP-GE-Z For more informati on about installing an SFP Gigabit Ethernet module, see the “Interf ace M odule Installation” section on page 3-17 .
1-14 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 1 Cisc o ASR 903 router Overview Cisco ASR 903 router Features 10 Gigabit Ethernet XFP Interface Module The 10 Gigabit Ethernet XFP interface module pro vides a single port supporting a 10 Gig abit Ethernet XFP module.
1-15 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 1 Cisco ASR 903 router Overview Cisco ASR 903 router Features • D WDM-XFP-46.92 • D WDM-XFP-47.72 • D WDM-XFP-48.51 • D WDM-XFP-50.12 • D WDM-XFP-50.92 • D WDM-XFP-51.
1-16 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 1 Cisc o ASR 903 router Overview Cisco ASR 903 router Features T1/E1 Interface Module The T1/E1 interface mod u le pro vides connecti vity for up to 16 T1/E1 ports through a 100-pin Amplimite connector .
1-17 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 1 Cisco ASR 903 router Overview Cisco ASR 903 router Features Figure 1-11 sh ow s the interface modul e.
1-18 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 1 Cisc o ASR 903 router Overview Cisco ASR 903 router Features Figur e 1 -12 Ser ial Interface Module Figure 1-13 pro vides an over view of the Cisco ASR 903 router fro nt panel.
1-19 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 1 Cisco ASR 903 router Overview Cisco ASR 903 router Features Figur e 1 -13 Cisco A SR 903 r out er F r ont P anel For more inf ormation about using the LEDs to troubleshoot t he Cisco ASR 903 router, see Chapter 5, “T roub leshooting.
1-20 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 1 Cisc o ASR 903 router Overview Interface Numbering Temperature Sensor The Cisco ASR 903 router has a temperat ure sensor to detect overtemperature co nditions inside the chassis.
1-21 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 1 Cisco ASR 903 router Overview Regulatory Compliance Figure 1-15 sho ws inte rface numbering in a Cisco ASR 903 rou ter.
1-22 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 1 Cisc o ASR 903 router Overview Regulatory Compliance.
CH A P T E R 2-1 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 2 Preparing for Installation The following sections de scribe ho w to prepare for the installat ion of the Cisco A SR 903.
2-2 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 2 Preparing for Installatio n Safety Guidelines Standard Warning Statements T o see translations of the warni n gs that appear in this publication , refer to the Regulator y Compliance and Safety Information document that accompanied this device.
2-3 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 2 Pre paring for Installation Safety Guidelines Safety Guidelines for Personal Safety and Equipment Protection The follo wing guidelines help ensure your saf ety and protect the equipm ent.
2-4 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 2 Preparing for Installatio n Safety Guidelines War ni n g Invisible laser radiation may be emitted from disconnect ed fibers or connectors. Do not stare into beams or view directly with optical instruments.
2-5 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 2 Pre paring for Installation Safety Guidelines War ni n g When you connect or disconnect the powe r and relay connector with po wer applied, an electrical arc can occur . This could cause an explo sion in hazardous area insta llations.
2-6 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 2 Preparing for Installatio n Safety Guidelines War ni n g Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.
2-7 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 2 Pre paring for Installation Safety Guidelines War ni n g Hazardous voltage or energy may be present on DC power termina ls. Always replace cover when terminals are not in service.
2-8 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 2 Preparing for Installatio n Safety Guidelines Power Supply Considerations Check the power at your site to en sure that you are receiving clean po wer (free of spikes and noi se).
2-9 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 2 Pre paring for Installation Site Planning Site Planning The follo wing sections describe how to plan for the installation of.
2-10 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 2 Preparing for Installatio n Site Planning • Consideration has been gi ven to the consol e port wiring and limitations of the cabling in vo lved, according to TIA/EIA- 232F .
2-11 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 2 Pre paring for Installation Site Planning Air Flow Guidelines Cool air is circulated through the Cisco ASR 903 Router by a fan tray lo cated along the right si de of the router .
2-12 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 2 Preparing for Installatio n Site Planning Air Flow Guidelines for Enclosed Rack Installation T o install a Cisco ASR 90 3 Ro.
2-13 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 2 Pre paring for Installation Site Planning The maximum po wer draw of the Cisco ASR 903 Router chassis and its confi gurable hardware components a re listed in th e following table.
2-14 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 2 Preparing for Installatio n Site Planning The extent of yo ur network and the distances b etween the network int erface conn.
2-15 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 2 Pre paring for Installation Site Planning If you use twisted- pair cable in your plant wiring w ith a good distrib ution of groundi ng conductors, th e plant wiring is unlik ely to emit radio interferen ce.
2-16 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 2 Preparing for Installatio n Site Planning The distance between the center lines of th e mounting holes on the tw o mounting posts must be 18.3 1 inches ± 0.06 inch (46.5 0 cm ± 0.
2-17 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 2 Pre paring for Installation Site Planning • Use the show en vironment all command regularly to check the internal system status.
2-18 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 2 Preparing for Installatio n Site Planning Installation Checklist T o assis t you with your ins tallation and to provide a record of w hat was done by whom and when, photocopy the Cisco ASR 903 Router Installatio n Checklist sho wn in Ta b l e 2 - 1 .
2-19 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 2 Pre paring for Installation Receiving the Cisco ASR 903 Router Creating a Site Log The Site Log provides a record of all the acti ons related to installing and maintaining the router .
2-20 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 2 Preparing for Installatio n Receiving the Cisco ASR 903 Router Chassis-Lifting Guidelines The chassis is not intended to be mo ved frequently .
2-21 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 2 Pre paring for Installation Receiving the Cisco ASR 903 Router Note For more information on cable specif ications, see Chapter 5, “Troublesh ooting.
2-22 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 2 Preparing for Installatio n Receiving the Cisco ASR 903 Router Note Most Cisco documentation is a vailable o nline.
CH A P T E R 3-1 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 3 Installing the Cisco ASR 903 Router This chapter de scribes ho w to in stall the Cisco ASR 903 Router and includes the .
3-2 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Installing the Router in a Rack Installing the Chassis Brackets The chassis is shipped with mounting brackets that can be installed on the front or rear of the chassis.
3-3 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Installing the Router in a Ra ck Note The A903-F AN-E fan tray with f ilter (A903-F AN-F) cannot be mounted usin g the mounting scre ws that are supported for A903-F AN fan tray .
3-4 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Installing the Router in a Rack Figure 3-4 Installing the Chassis to su ppor t the Japane.
3-5 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Installing the Router in a Ra ck Figure 3-6 Cisco A SR 903 Chassis with Air Plenum Atta.
3-6 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Installing the Router in a Rack T o install the optiona l cable management brackets, p er.
3-7 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Installing the Chassis Ground Connection Installing the Chassis Ground Connection Befor.
3-8 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Installing the Chassis Ground Connection T o ensure that the chassis grou nd connection t.
3-9 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Installing the Chassis Ground Connection Step 3 Using a crimping tool (as specified by the ground lug ma nufacturer), crimp the grou nd lug to the ground wire as shown in Figure 3-12 .
3-10 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Installing th e Fan Tray Installing the Fan Tray The fan tray is a modular unit th at provides cooli ng to th e Cisco A SR 903 Rou ter.
3-11 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Installing the Fan Tra y Step 3 Slide the dust f ilter onto the fan tray . See Figure 1-5 . Step 4 Insert the dummy co ver on the f an tray to secure t he filter with in the chassis.
3-12 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Installing th e Fan Tray Caution T o av oid erroneous failure messages, all ow at least 2 min utes for the system to reinitialize after the fan tray has been remov ed or replaced.
3-13 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router RSP Installation Step 3 Pull the fa n tray backw a rd to ward you no more than 1 inch to diseng age it from the po wer receptacle on the midplane, as shown in Fig ure 3-15 .
3-14 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router RSP Installation Installing an RSP Module T o install an RSP module in th e router chassi s, perform the followi ng steps: Step 1 Choose a slot for the module.
3-15 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router RSP Installation Step 7 V erify that the captiv e installation screws are tig htened on all of the modules installed in the chassis.
3-16 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router RSP Installation Step 5 Grasp the front edge of the module and slide the module straight out of the slot. If the chassis has horizontal slots, place your hand under the module to support its weight as you slide it out from the slot.
3-17 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Interface Module Installation • When inserting multiple IMs int o the chassis, wait until each IM reaches an OK state be fore inserting the ne xt IM.
3-18 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Interface Module Installation Caution Do not use interface mo dule and po wer supply ejector handles to lift the chassis; using th e handles to lift the chassis can deform or damage th e handles.
3-19 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Installing the Power Supply Caution T o avoid err oneous failure messages, note the cu.
3-20 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Installing the Power Supply Preventing Power Loss Use the follo wing guidelines to pre vent po wer loss to the router .
3-21 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Installing the Power Supply Guidelines for AC-Powered Systems Basic guidelines for A C-powered systems include the follo wing: • Each chassis po wer supply should ha ve its own d edicated branch circuit.
3-22 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Installing the Power Supply Figur e 3-18 Installing the DC P ow er Supply Step 5 T ighten the captiv e installation screws of the po wer supply .
3-23 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Installing the Power Supply Figur e 3-19 DC P ow er Su pply with Lead Wires Step 4 Insert the e xposed wire of one of the three DC-input power source wires into the termi nal block plug.
3-24 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Installing the Power Supply Step 5 Use a ratcheting torque scre wdriver to torque the terminal block plug capti ve scre w (above th e installed wire lead) f ro m 4.
3-25 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Installing the Power Supply Caution Secure the wires coming in fro m the terminal block plu g so that they cannot be disturbed by casual contact.
3-26 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Installing the Power Supply Step 1 Follo w the steps to remove the po wer supply unit if installed in the ch assis. See Removi ng and Replacing the DC Power Supply , page 3-26 .
3-27 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Installing the Power Supply Note The Cisco ASR 903 Router po wer supplies are hot-swappable. If you ha ve installed redundant po wer supply modules, you can replace a si ngle po wer supply without interrupting po wer to the router .
3-28 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Installing the Power Supply War ni n g This product requires short-circuit (over current) protect ion, to be provided as part of the building installation.
3-29 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Installing the Power Supply • OUTPUT F AIL LED is green Step 4 If the LEDs indicate a po wer problem, see the Chapter 5, “T roubleshooting” for troubleshooting inform ation.
3-30 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Connecting the Cisc o ASR 903 Router to the Network Step 5 If the po wer supply bay is t.
3-31 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Connecting the Cisco ASR 903 Router to the Ne twork Connecting to the Serial Port using Microsoft Windows This procedure sho ws how to conn ect to the serial port us ing Microsoft W indo ws.
3-32 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Connecting the Cisc o ASR 903 Router to the Network Figure 3-24 Connecting the USB Conso.
3-33 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Connecting the Cisco ASR 903 Router to the Ne twork Connecting to the Console Port using Mac OS X This procedure describes how to connect a Mac OS X system USB port to the console using the built i n OS X T erminal utility .
3-34 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Connecting the Cisc o ASR 903 Router to the Network Installing the Cisco Microsoft Windo.
3-35 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Connecting the Cisco ASR 903 Router to the Ne twork Installing the Cisco Microso ft Windows Vista USB Driver This procedure sho ws how to in stall the Microsoft W indows V ista USB dri ver .
3-36 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Connecting the Cisc o ASR 903 Router to the Network Step 1 Run the setup.e xe for W indo ws 32-bit or setup(x64).ex e for W indows-64bit. Cl ick Next .
3-37 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Connecting the Cisco ASR 903 Router to the Ne twork T o connect a modem to the router , follow these steps: Step 1 Connect the RJ45 end of the adapter cable to th e black A UX port on the route r , as shown in Figure 3-25 .
3-38 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Connecting the Cisc o ASR 903 Router to the Network Connecting a Management Ethernet Cable When using the Ethernet Management port in the def ault mode (speed-auto and dup lex-auto) the port operates in auto-MDI/MDI-X mode .
3-39 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Connecting the Cisco ASR 903 Router to the Ne twork Figur e 3-26 Cisco AS R 903 Router.
3-40 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Connecting the Cisc o ASR 903 Router to the Network Step 3 Connect the other end to t he BTS patch or demarcation pa nel at your site. Step 4 T urn on power to the router .
3-41 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Connecting the Cisco ASR 903 Router to the Ne twork Connecting Cables to a GPS Interfa.
3-42 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Connecting the Cisc o ASR 903 Router to the Network War ni n g T o comply with the T elc.
3-43 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Connecting the Cisco ASR 903 Router to the Ne twork Connecting Cables to SFP Modules For information on conn ecting cables to Cisco optical and Ethernet SFP interf aces, see http://www .
3-44 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Connecting the Cisc o ASR 903 Router to the Network Figure 3-28 sho ws how the cable is connected betwee n th e T1/E1 interface module an d the patch panel.
3-45 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Connecting the Cisco ASR 903 Router to the Ne twork ports as described in GR-1089-CORE) and require isolation from the exposed OSP cabling.
3-46 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Connecting the Cisc o ASR 903 Router to the Network Figure 3-29 Suppor ted Ser ial Connectors Note The Cisco ASR 903 Router currently supp orts only the EIA/TIA-23 2 connector .
3-47 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 3 Insta lling the Cisco ASR 903 Router Connecting the Cisco ASR 903 Router to the Ne twork For more information on cable specif ications and pinouts, see Cha pter 5, “Troubleshooting” .
3-48 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 3 Installing the Cisco ASR 903 Router Connecting the Cisc o ASR 903 Router to the Network.
CH A P T E R 4-1 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 4 Cisco ASR 903 Router Initial Configuration This chapter guides you th rough a basic router co nfiguration, whic h is suf ficient for you to access yo ur network.
4-2 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 4 Cisco ASR 903 Router Initial Configurati on Powering Up the Cisco ASR 903 Router Powering Up the Cisco ASR 903 Router Make certain that all card slots and compartments are closed off.
4-3 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 4 Cisco ASR 903 Router Initial Configuration Powering Up the Cisco ASR 903 Router initrd at: 009B9000 01006219 isord at: 01007000 0D1DF800 avail ram: 00400000 00800000 Kernel load: Uncompressing image.
4-4 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 4 Cisco ASR 903 Router Initial Configurati on Powering Up the Cisco ASR 903 Router *Feb 19 17:34:29.720: %PARSER-4-BADCFG: Unexpected end of configuration file. *Feb 19 17:34:29.
4-5 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 4 Cisco ASR 903 Router Initial Configuration Configuring the Cisco ASR 903 Rou ter at Startup During the boot process, o bserve the system LEDs. The LEDs on the sh ared port adapter go on and of f in an irregu lar sequence.
4-6 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 4 Cisco ASR 903 Router Initial Configurati on Configuring the Cisco ASR 903 Router at Startup For informati on on modifying the conf iguration after you create it, see the Cisco IOS configuration and command reference guides.
4-7 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 4 Cisco ASR 903 Router Initial Configuration Configuring the Cisco ASR 903 Rou ter at Startup Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec.
4-8 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 4 Cisco ASR 903 Router Initial Configurati on Safely Powering Off the Cisco ASR 903 Router Safely Powering Off the Cisco ASR 903 Router This section e xplains how to shu t do wn the Cisco ASR 903 Router.
CH A P T E R 5-1 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 5 Troubleshooting The follo wing sections provide information for t roubleshooting problems on the Cisco ASR 903 Router.
5-2 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 5 Troubleshooting Pinouts GPS Port Pinout Ta b l e 5 - 2 summarizes the GPS port pinouts.
5-3 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 5 Troubleshooting Pinouts Alarm Port Pinout Ta b l e 5 - 4 summarizes the external alarm input pinout. Console/Aux RJ45 RS232 Serial Port Pinout Ta b l e 5 - 5 summarizes the console/aux RJ45 RS232 serial port pinout.
5-4 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 5 Troubleshooting Pinouts T1/E1 Port Pinout Ta b l e 5 - 6 summarizes the pinouts of the cable (T yco part number 21634 42-1, Cisco part number 72-5184-01) used to connect the T1/E1 interface module to the rear of the p atch panel.
5-5 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 5 Troubleshooting Pinouts Figure 5-1 sho ws the wiring schematic of the cable used to conn ect the T1/E1 interface mod ule to the rear of the patch panel.
5-6 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 5 Troubleshooting Pinouts DB-9 Connector Pinouts Ta b l e 5 - 7 summarizes the pinouts for each serial in terface type when usin g a DB-9 connector . Note T wisted pairs are 2-5, 6-8, 4-7.
5-7 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 5 Troubleshooting Pinouts Note The X.21, V .35, RS-485, EIA-449, EIA-530, an d IRIG-B standards are not currently supp orted by software. Management Ethernet Port Pinout Ta b l e 5 - 9 sum marizes the M anagement Ethe rnet port pinout .
5-8 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 5 Troubleshooting LED Summary Note USB TYPE-A receptac le used. Note The USB flash/MEM port +5VDC is output. W e provide power f o r USB flash/MEM, and it operates as a USB host device.
5-9 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 5 Troubleshooting LED Summary Interface Module LEDs Ta b l e 5 - 1 3 summarizes the interface modul e LEDs.
5-10 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 5 Troubleshooting LED Summary OC-3 Interface Module LEDs Ta b l e 5 - 1 5 summarizes the LEDs for the OC-3 interf ace module.
5-11 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 5 Troubleshooting LED Summary T1/E1 Interface Module LEDs Ta b l e 5 - 1 5 summarizes the LEDs for the T1/E1 interface module. Serial Interface Module LEDs Ta b l e 5 - 1 5 summarizes the LEDs for the serial in terface module.
5-12 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 5 Troubleshooting LED Summary Power Supply LEDs Ta b l e 5 - 1 8 summarizes the po wer supply LEDs for both the A C and DC po wer supplies.
5-13 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-05 Chapter 5 Troubleshooting LED Summary Fan Tray LEDs Ta b l e 5 - 1 9 summarizes the fan tray LEDs. Alarm Conditions Ta b l e 5 - 2 0 summarizes the meaning of alarm condit ions on the Cisco ASR 903 Router.
5-14 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Chapter 5 Troubleshooting LED Summary.
6-1 Cisco ASR 903 Router Hard ware Installati on Guide OL-25178-05 APPENDIX 6 Site Log and Manufactures Use the Site Log to provide a recor d of actio ns related t o installing and mainta ining the r outer . Keep it in an accessible place near the c hassis so that those who performs tasks have access to it.
6-2 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Appendix 6 Site Log and Manufactu res T able 6-1 Site Log Date Description of Action Performed or Symptom Observed Initials.
6-3 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Appendix 6 Site Log and Manu factures Manufactures Manufactures Ta b l e 6 - 2 lists the manufacturers for equipment used with the Cisco ASR 903 router . T able 6-2 Manufactur es Manufacturer Web Site or Phone Number Products/Model GA W 1 1.
6-4 Cisco ASR 903 Router Hardware Installation Guide OL-25178-05 Appendix 6 Site Log and Manufactu res Manufactures.
IN-1 Cisco ASR 903 Router Hardware Installation Guide OL-25178-03 INDEX A airflow chassis clearance 2-16 altitude 2-10 auxiliary port connecting to a modem 3-34 to ?? B back panel 3-6, 3-7 C cable len.
Index IN-2 Cisco ASR 903 Router Hard ware Installation Guide OL-25178-03 N numbering interface 1-17 P PC connecting t o router ?? to 3-28 power surge suppression 2-14 power lines (wa rning) 2-4 power .
An important point after buying a device Cisco Systems ASR 903 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cisco Systems ASR 903 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cisco Systems ASR 903 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cisco Systems ASR 903 you will learn all the available features of the product, as well as information on its operation. The information that you get Cisco Systems ASR 903 will certainly help you make a decision on the purchase.
If you already are a holder of Cisco Systems ASR 903, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cisco Systems ASR 903.
However, one of the most important roles played by the user manual is to help in solving problems with Cisco Systems ASR 903. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cisco Systems ASR 903 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
