Instruction/ maintenance manual of the product 22675723 Chevrolet
Go to page of 341
.
i 2002 Chevrolet Malibu Owner ’ s Manual Litho in U.S.A. Copyright General Motors Corporation 06/25/01 Part Number 22675723 A First Edition All Rights Reserved.
ii GENERAL MOTORS, GM, the GM Emblem, CHEVROLET , the CHEVROLET Emblem and the name MALIBU are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. W e reserve the right to make changes after that time without further notice.
iii How to Use this Manual Many people read their owne r ’ s manual from beginning to end when they first receive their new vehicle. If you do this, it will help you learn about the features and controls for your vehicle. In this manual, you’ll find that pictures and words work together to explain things quickl y .
iv V ehicle Damage W arnings Also, in this book you will find these notices: NOTICE: These mean there is something that could damage your vehicle. In the notice area, we tell you about something that can damage your vehicle. Many times, this damage would not be covered by your warranty , and it could be costly .
v These are some examples of vehicle symbols you may find on your vehicle:.
1- 1-1 Section 1 Seats and Seat Restraints Here you’ll find information about the seats in your vehicle and how to use your safety belts properly . Y ou can also learn about some things you should not do with air bags and safety belts.
1-2 Seats and Seat Controls This section tells you about the seats -- how to adjust them -- and also about reclining seatbacks and head restraints. Manual Front Seats CAUTION: Y ou can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving.
1-3 Six-W ay Power Seat (If Equipped) If your vehicle has this feature, the power seat control is located on the outboard side of the driver ’ s seat. This control allows you to move the seat up, down, forward or backward. It will also move the front or rear of the seat cushion up or down.
1-4 Reclining Front Seatbacks Y our vehicle has the following reclining front seatback lever . T o adjust the seatback, lift the lever located on the outboard side of the seat. Move the seatback to where you want it and release the lever . Check to see that the handle returns to the original position and that the seatback is securely locked.
1-5 CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can’t do their job when you’re r eclined like this. The shoulder belt can’t do its job because it won’t be against your body .
1-6 Rear Seats Folding Rear Seatback (Option) T o fold down the rear seatback, do the following: 1. Open the trunk and pull one or both of the tethers located on the driver ’ s side of the trunk. The left tether will open the larger side of the seatback.
1-7 Safety Belts: They’re for Everyone This part of the manual tells you how to use safety belts properly . It also tells you some things you should not do with safety belts. And it explains the Supplemental Restraint System (SRS), or air bag system.
1-8 Y ou never know if you’ll be in a crash. If you do have a crash, you don’t know if it will be a bad one. A few crashes are mild, and some crashes can be so serious that even buckled up a person wouldn’t survive. But most crashes are in between.
1-9 Put someone on it. Get it up to speed. Then stop the vehicle. The rider doesn’t stop..
1-10 The person keeps going until stopped by something. In a real vehicle, it could be the windshield ... or the instrument panel ....
1-1 1 or the safety belts! W ith safety belts, you slow down as the vehicle does. Y ou get more time to stop. Y ou stop over more distance, and your strongest bones take the forces.
1-12 Q: If my vehicle has air bags, why should I have to wear safety belts? A: Air bags are in many vehicles today and will be in most of them in the future. But they are supplemental systems only; so they work with safety belts -- not instead of them.
1-13 How to W ear Safety Belts Properly Adults This part is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and babies. If a child will be riding in your vehicle, see the part of this manual called “Children.
1-14 If the belt stops before it reaches the buckle, tilt the latch plate and keep pulling until you can buckle the belt. Pull up on the latch plate to make sure it is secure. If the belt isn’t long enough, see “Safety Belt Extender” at the end of this section.
1-15 The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you’d be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
1-16 Shoulder Belt Height Adjuster Before you begin to drive, move the shoulder belt adjuster to the height that is right for you. T o move it down, squeeze the release button and move the height adjuster to the desired position. Y ou can move the adjuster up just by pushing up on the shoulder belt guide.
1-17 Q: What’ s wrong with this? A: The shoulder belt is too loose. It won’t give nearly as much protection this way . CAUTION: Y ou can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury .
1-18 Q: What’ s wrong with this? A: The belt is buckled in the wrong place. CAUTION: Y ou can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be ther e, not at the pelvic bones.
1-19 Q: What’ s wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. CAUTION: Y ou can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury .
1-20 Q: What’ s wrong with this? A: The belt is twisted across the body . CAUTION: Y ou can be seriously injured by a twisted belt. In a crash, you wouldn’t have the full width of the belt to spread impact for ces. If a belt is twisted, make it straight so it can work properly , or ask your dealer to fix it.
1-21 T o unlatch the belt, just push the button on the buckle. The belt should go back out of the way . Before you close the door , be sure the belt is out of the way . If you slam the door on it, you can damage both the belt and your vehicle. Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women.
1-22 The best way to protect the fetus is to protect the mother . When a safety belt is worn properly , it’ s more likely that the fetus won’t be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly .
1-23 CAUTION: Air bags inflate with great for ce, faster than the blink of an eye. If you’re too close to an inflating air bag, as you would be if you were leaning forward, it could seriously injure you. Safety belts help keep you in position before and during a crash.
1-24 How the Air Bag System W orks Where ar e the air bags? The driver ’ s air bag is in the middle of the steering wheel. The right front passenger ’ s air bag is in the instrument panel on the passenger ’ s side.
1-25 CAUTION: If something is between an occupant and an air bag, the bag might not inflate properly or it might force the object into that person causing sever e injury or even death.
1-26 How does an air bag restrain? In moderate to severe frontal or near - frontal collisions, even belted occupants can contact the steering wheel or the instrument panel.
1-27 Y our vehicle is equipped with a crash sensing and diagnostic module, which records information about the air bag system. The module records information about the readiness of the system, when the system commands air bag inflation and driver ’ s safety belt usage at deployment.
1-28 Rear Seat Passengers It’ s very important for rear seat passengers to buckle up! Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts. Rear passengers who aren’t safety belted can be thrown out of the vehicle in a crash.
1-29 If the belt stops before it reaches the buckle, tilt the latch plate and keep pulling until you can buckle it. Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see “Safety Belt Extender” at the end of this section.
1-30 The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you’d be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
1-31 Rear Safety Belt Comfort Guides for Children and Small Adults Rear shoulder belt comfort guides will provide added safety belt comfort for older children who have outgrown booster seats and for small adults. When installed on a shoulder belt, the comfort guide better positions the belt away from the neck and head.
1-32 2. Slide the guide under and past the belt. The elastic cord must be under the belt. Then, place the guide over the belt, and insert the two edges of the belt into the slots of the guide. 3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top.
1-33 4. Buckle, position and release the safety belt as described in “Rear Seat Outside Passenger Positions” earlier in this section. Make sure that the shoulder belt crosses the shoulder . T o remove and store the comfort guides, squeeze the belt edges together so that you can take them out of the guides.
1-34 Lap Belt When you sit in the center seating position, you have a lap safety belt, which has no retractor . T o make the belt longer , tilt the latch plate and pull it along the belt. T o make the belt shorter , pull its free end as shown until the belt is snug.
1-35 Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints.
1-36 CAUTION: People should never hold a baby in their arms while riding in a vehicle. A baby doesn’t weigh much -- until a crash. During a crash a baby will become so heavy it is not possible to hold it. CAUTION: (Continued) CAUTION: (Continued) For example, in a crash at only 25 mph (40 km/h), a 12 - lb.
1-37 CAUTION: Children who ar e up against, or very close to, any air bag when it inflates can be seriously injured or killed. Air bags plus lap - shoulder belts offer outstanding protection for adults and older children, but not for young childr en and infants.
1-38 CAUTION: Newborn infants need complete support, including support for the head and neck. This is necessary because a newborn infant’ s neck is weak and its head weighs so much compared with the rest of its body .
1-39 Restraint Systems for Children An infant car bed (A), a special bed made for use in a motor vehicle, is an infant restraint system designed to restrain or position a child on a continuous flat surface. Make sure that the infant’ s head rests toward the center of the vehicle.
1-40 A forward - facing child seat (C - E) provides restraint for the child’ s body with the harness and also sometimes with surfaces such as T - shaped or shelf - like shields. A booster seat (F - G) is a child restraint designed to improve the fit of the vehicle’ s safety belt system.
1-41 Q: How do child restraints work? A: A child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position children. A built - in child restraint system is a permanent part of the motor vehicle. An add - on child restraint system is a portable one, which is purchased by the vehicle’ s owner .
1-42 Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. General Motors, therefore, recommends that child restrai.
1-43 In Canada, the law requires that forward - facing child restraints have a top strap, and that the strap be anchored. In the United States, some child restraints also have a top strap. If your child restraint has a top strap, it should be anchored.
1-44 Lower Anchorages and T op T ethers for Children (LA TCH System) Y our vehicle has the LA TCH system. Y ou’ll find anchors (A) in the rear outside seating positions.
1-45 W ith this system, use the LA TCH system instead of the vehicle’ s safety belts to secure a child restraint. CAUTION: If a LA TCH - type child restraint isn’t attached to its anchorage points, the restraint won’t be able to protect a child sitting ther e.
1-46 Securing a Child Restraint Designed for the LA TCH System 1. Find the anchors for the seating position you want to use, where the bottom of the seatback meets the back of the seat cushion. 2. Put the child restraint on the seat. 3. Attach the anchor points on the child restraint to the anchors in the vehicle.
1-47 T ilt the latch plate to adjust the belt if needed. If the shoulder belt goes in front of the child’ s face or neck, put it behind the child restraint. 3. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to.
1-48 4. T o tighten the belt, pull up on the shoulder belt while you push down on the child restraint. If you’re using a forward - facing child restraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt.
1-49 Securing a Child Restraint in the Center Rear Seat Position Y ou’ll be using the lap belt. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say . See the earlier part about the top strap if the child restraint has one.
1-50 4. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 5. T o tighten the belt, pull its free end while you push down on the child restraint.
1-51 Securing a Child Restraint in the Right Front Seat Position Y our vehicle has a right front passenger air bag. Never put a rear - facing child restraint in this seat. Here’ s why: CAUTION: A child in a rear - facing child restraint can be seriously injur ed or killed if the right front passenger’ s air bag inflates.
1-52 4. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock.
1-53 6. T o tighten the belt, feed the shoulder belt back into the retractor while you push down on the child restraint. Y ou may find it helpful to use your knee to push down on the child restraint as you tighten the belt. 7. Push and pull the child restraint in different directions to be sure it is secure.
1-54 Older Children Older children who have outgrown booster seats should wear the vehicle’ s safety belts. If you have the choice, a child should sit next to a window so the child can wear a lap - shoulder belt and get the additional restraint a shoulder belt can provide.
1-55 CAUTION: Never do this. Here two childr en are wearing the same belt. The belt can’t properly spr ead the impact forces. In a crash, the two children can be crushed together and seriously injur ed. A belt must be used by only one person at a time.
1-56 CAUTION: Never do this. Here a child is sitting in a seat that has a lap - shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way , in a crash the child might slide under the belt. The belt’ s force would then be applied right on the child’ s abdomen.
1-57 Safety Belt Extender If the vehicle’ s safety belt will fasten around you, you should use it. But if a safety belt isn’t long enough to fasten, your dealer will order you an extender . It’ s free. When you go in to order it, take the heaviest coat you will wear , so the extender will be long enough for you.
2- 2-1 Section 2 Featur es and Controls Here you can learn about the many standard and optional features on your vehicle, and information on starting, shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is working properly -- and what to do if you have a problem.
2-2 Windows CAUTION: Leaving childr en in a vehicle with the windows closed is dangerous. A child can be over come by the extreme heat and can suffer permanent injuries or even death from heat str oke. Never leave a child alone in a vehicle, especially with the windows closed in warm or hot weather .
2-3 Manual Windows On a vehicle with manual windows, use the window crank to open and close each window . Power W indows (If Equipped) The power window switches are located on the armrest on the driver ’ s door . In addition, each passenger door has a switch for its own window .
2-4 Keys CAUTION: Leaving childr en in a vehicle with the ignition key is dangerous for many r easons. A child or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. Don’t leave the keys in a vehicle with children.
2-5 One key is used for the ignition and all other locks. When a new vehicle is delivered, the key has a bar - coded key tag. This tag may be removed by your dealer before it is delivered. Each tag has a key code on it that tells your dealer or a qualified locksmith how to make extra keys.
2-6 Door Locks CAUTION: Unlocked doors can be dangerous. Passengers -- especially childr en -- can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle won’t open it. Y ou increase the chance of being thrown out of the vehicle in a crash if the doors aren’t locked.
2-7 Power Door Locks W ith the power door locks, you can unlock or lock all the doors on your vehicle using either the driver ’ s or front passenger ’ s door lock switch. Pull up on the switch to unlock all the doors. Push down on it to lock all the doors.
2-8 Customizing the Automatic Door Locks One of four operating modes may be selected and programmed by the driver: Mode 1: All doors automatically lock when the transaxle is shifted out of P ARK (P). The doors will remain locked unless manually unlocked or the lock button is pressed.
2-9 Delayed Locking This feature will allow the driver to delay the actual locking of the vehicle. This feature will not operate if the key is left in the ignition.
2-10 The rear doors on your vehicle cannot be opened from the inside when this feature is in use. If you want to open a rear door while the security lock is on, do the following: 1. Unlock the door from the inside. 2. Then open the door from the outside.
2-1 1 Remote Keyless Entry System (If Equipped) If your vehicle has this feature, you can lock and unlock your doors or unlock your trunk from about 3 feet (1 m) up to 30 feet (9 m) away using the remote keyless entry transmitter supplied with your vehicle.
2-12 Operation The following functions are available with the keyless entry system: (Lock): All doors will automatically lock when this button on the transmitter is pressed.
2-13 Programmable Horn Chirp When you use the remote keyless entry transmitter to lock the doors or use the delayed locking feature, the parking lamps will flash twice.
2-14 Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about four years. Y ou can tell the battery is weak if the transmitter won’t work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it’ s probably time to change the battery .
2-15 T runk T o unlock the trunk from the outside, insert the key and turn the trunk lock cylinder . When closing the trunk, close from the center to ensure it fully latches. CAUTION: It can be dangerous to drive with the trunk lid open because carbon monoxide (CO) gas can come into your vehicle.
2-16 Remote T runk Release Press the remote trunk release button, located on the lower left side of the instrument panel, to release the trunk lid. Make sure the remote trunk release lockout feature is not activated.
2-17 T runk Release Handle NOTICE: The trunk release handle was not designed to be used to tie down the trunk lid or as an anchor point when securing items in the trunk. Improper use of the trunk release handle could damage it. There is a glow - in - the - dark trunk release handle located inside the trunk on the trunk latch.
2-18 Theft V ehicle theft is big business, especially in some cities. Although your vehicle has a number of theft - deterrent features, we know that nothing we put on it can make it impossible to steal.
2-19 Passlock Y our vehicle is equipped with the Passlock theft - deterrent system. Passlock is a passive theft - deterrent system. Passlock enables fuel if the ignition lock cylinder has not been tampered with.
2-20 Ignition Positions W ith the key in the ignition switch, you can turn it to four different positions. A (OFF): This is the only position from which you can remove the key . It also locks your ignition and transaxle. A warning chime will sound if you open the driver ’ s door when the ignition is off and the key is in the ignition.
2-21 C (ON): This position unlocks the ignition. It is also the position to where the key returns after you start the engine and release the switch. The switch will stay in this position when the engine is running.
2-22 NOTICE: Holding your key in ST AR T for longer than 15 seconds at a time will cause your battery to be drained much sooner . And the excessive heat can damage your starter motor . W ait about 15 seconds between each try to help avoid draining your battery or damaging your starter .
2-23 T o Use the Engine Coolant Heater 1. T urn off the engine. 2. Open the hood and unwrap the electrical cord. The engine coolant heater cord is located near the engine air cleaner/filter . 3. Plug it into a normal, grounded 1 10 - volt AC outlet. CAUTION: Plugging the cord into an ungrounded outlet could cause an electrical shock.
2-24 Automatic T ransaxle Operation Y our automatic transaxle has a shift lever located on the console between the seats. P ARK (P): This position locks your front wheels. It’ s the best position to use when you start your engine because your vehicle can’t move easily .
2-25 Ensure the shift lever is fully in P ARK (P) before starting the engine. Y our vehicle has an automatic transaxle shift lock control system. Y ou have to apply your regular brake before you can shift from P ARK (P) when the ignition key is in ON.
2-26 AUT OMA TIC OVERDRIVE (D): This position is for normal driving. If you need more power for passing, and you’re: Going less than 35 mph (56 km/h), push your accelerator pedal about halfway down. Going about 35 mph (56 km/h) or more, push the accelerator all the way down.
2-27 NOTICE: (Continued) Use AUTOMA TIC OVERDRIVE (D) or THIRD (3) as much as possible. Don’t shift into SECOND (2) unless you are going slower than 65 mph (105 km/h) or you can damage your engine. FIRST (1): This position gives you even more power (but lower fuel economy) than SECOND (2).
2-28 Parking Brake T o set the parking brake, push down the parking brake pedal with your left foot. If the ignition is on, the brake system warning light will come on. T o release the parking brake, hold the regular brake pedal down with your right foot.
2-29 Shifting Into P ARK (P) CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in P ARK (P) with the parking brake firmly set. Y our vehicle can roll. If you have left the engine running, the vehicle can move suddenly .
2-30 Leaving Y our V ehicle W ith the Engine Running CAUTION: It can be dangerous to leave your vehicle with the engine running. Y our vehicle could move suddenly if the shift lever is not fully in P ARK (P) with the parking brake firmly set. And, if you leave the vehicle with the engine running, it could overheat and even catch fire.
2-31 Shifting Out of P ARK (P) Y our vehicle has an automatic transaxle shift lock control system. Y ou have to apply your regular brake before you can shift from P ARK (P) when the ignition is in ON. See “Automatic T ransaxle Operation” in the Index.
2-32 Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you can’t see or smell. It can cause unconsciousness and death. Y ou might have exhaust coming in if: Y our exhaust system sounds strange or different.
2-33 CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in P ARK (P) with the parking brake firmly set. Y our vehicle can roll. Don’t leave your vehicle when the engine is running unless you have to. If you’ve left the engine running, the vehicle can move suddenly .
2-34 T urn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: T urn and Lane - Change Signals Headlamp High/Low - Beam Changer Flash - to - Pass For information on the exterior lamps, see “Exterior Lamps” later in this section.
2-35 If a bulb is burned out, replace it to help avoid an accident. If the arrows don’t go on at all when you signal a turn, check for burned - out bulbs and then check the fuse.
2-36 OFF: Move the lever to OFF to turn off the windshield wipers. INT (Intermittent): Move the lever to INT to choose a delayed wiping cycle. T urn the INT ADJ band down for a longer delay or up for a shorter delay .
2-37 Cruise Control (If Equipped) W ith cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator . This can really help on long trips. Cruise control does not work at speeds below 25 mph (40 km/h).
2-38 Setting Cruise Control CAUTION: If you leave your cruise control switch on when you’re not using cruise, you might hit a button and go into cruise when you don’t want to. Y ou could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
2-39 Increasing Speed While Using Cruise Contr ol There are two ways to go to a higher speed. Use the accelerator pedal to get to the higher speed. Push the SET DECEL button, then release the button and the accelerator pedal. Y ou’ll now cruise at the higher speed.
2-40 Exterior Lamps The lever on the left side of the steering column operates the exterior lamps. The exterior lamp switch has three positions: (Parking Lamps) : T urning the switch to this position .
2-41 Daytime Running Lamps Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day . DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset.
2-42 The ALC system may also be on when driving through a parking garage, heavy overcast weather or a tunnel. This is normal. There is a delay in the transition between the daytime and nighttime operation of the DRL and the ALC systems so that driving under bridges or bright overhead street lights does not affect the system.
2-43 Fog Lamps (If Equipped) The button for the fog lamps is located on the instrument panel, to the left of the steering wheel. When using the fog lamps, the ignition must be on as well as the parking lamps or the low - beam headlamps. Push the button to turn the fog lamps on.
2-44 Illuminated Entry/Exit System When you open any door , the lamps inside of your vehicle will go on. These lamps will fade out 10 seconds after the last door is closed, or when the ignition is turned on after all doors have been closed.
2-45 Mirrors Inside Day/Night Rearview Mirror This mirror can be adjusted two ways. First, to adjust the angle of the mirror , move the mirror to a position that allows you see to out of the back window . T o adjust the height of the mirror , adjust the arm that connects the mirror to the windshield.
2-46 Power Remote Control Rearview Mirr ors (If Equipped) The controls for the power mirrors are located on the driver ’ s door armrest. Move the selector switch located above the four - way control pad to choose the right or left mirror . If you place the selector switch in the center position, no movement of the mirror will occur .
2-47 Storage Compartments Glove Box T o open, pull the handle to the left and pull the glove box door down until it stops and is fully open. Instrument Panel Cupholder The instrument panel cupholder is located to the left of the steering wheel. T o use it, pull it out until the rubber insert is revealed.
2-48 Ashtray and Cigarette Lighter The ashtray is located at the lower part of the center of the instrument panel. T o remove the ashtray for cleaning, pull up on the metal tab and pull the bin out. NOTICE: Don’t put papers and other things that burn into your ashtrays.
2-49 Accessory Power Outlet W ith accessory power outlets you can plug in auxiliary electrical equipment such as a cellular telephone or CB radio. The accessory power outlet is located to the right of the ashtray . The accessory power outlet is protected by a fuse and has a maximum current level.
2-50 When adding electrical equipment, be sure to follow the proper installation instructions included with the equipment. NOTICE: Power outlets are designed for accessory plugs only . Do not hang any type of accessory or accessory bracket fr om the plug.
2-51 Sunr oof (Option) If your vehicle has a sunroof, the switch is located on the headliner between the sun visors. The sunroof can be opened to a vent position or it can be express - opened all of the way . T o open the sunroof to the vent position, you must first open the sunshade by hand.
2-52 The Instrument Panel -- Y our Information System.
2-53 The main components of your instrument panel are the following: A. Side W indow Defogger V ents B. V ent Outlets C. Instrument Panel Brightness Thumbwheel D. Fog Lamp Button (If Equipped) E. Turn Signal/Multifunction Lever F . Cruise Control Buttons (If Equipped) G.
2-54 Instrument Panel Cluster Y our instrument panel cluster is designed to let you know at a glance how your vehicle is running. Y ou’ll know how fast you’re going, how much fuel you’re using, and many other things you will need to drive safely and economically .
2-55 Speedometer and Odometer Y our speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Y our odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada).
2-56 T achometer The tachometer shows your engine speed in revolutions per minute (rpm). NOTICE: Do not run your engine at speeds in the red ar ea, or engine damage may occur . W a rning Lights, Gages and Indicators This part describes the warning lights and gages that may be on your vehicle.
2-57 Gages can indicate when there may be or is a problem with one of your vehicle’ s functions. Often gages and warning lights work together to let you know when there’ s a problem with your vehicle.
2-58 Air Bag Readiness Light There is an air bag readiness light on the instrument panel, which shows the air bag symbol. The system checks the air bag’ s electrical system for malfunctions.
2-59 Charging System Indicator Light The charging system indicator light will come on when you turn on the ignition, but the engine is not running, as a check to show you it is working.
2-60 If the light and chime come on while you are driving, pull off the road and stop carefully . Y ou may notice that the pedal is harder to push. Or , the pedal may go closer to the floor . It may take longer to stop. If the light is still on, have the vehicle towed for service.
2-61 Engine Coolant T emperature Gage United States Canada This gage shows the engine coolant temperature. If the gage pointer moves into the red area, the light comes on and you hear a chime, your engine is too hot! It means that your engine coolant has overheated.
2-62 Malfunction Indicator Lamp (Check Engine Light) United States Canada Y our vehicle is equipped with a computer which monitors operation of the fuel, ignition and emission control systems.
2-63 This light should come on, as a check to show you it is working, when the ignition is on and the engine is not running. If the light doesn’t come on, have it repaired. This light will also come on during a malfunction in one of two ways: Light Flashing -- A misfire condition has been detected.
2-64 Have you recently changed brands of fuel? If so, be sure to fuel your vehicle with quality fuel. See “Fuel” in the Index. Poor fuel quality will cause your engine not to run as efficiently as designed.
2-65 Oil Pressur e Light If you have a low engine oil pressure problem, this light will stay on after you start your engine, or come on and you will hear a chime when you are driving. This indicates that your engine is not receiving enough oil. The engine could be low on oil, or could have some other oil problem.
2-66 Check Oil Light Y ou will have a CHECK OIL light in your instrument panel cluster . This light will come on briefly when you start your vehicle. If the light stays on after starting your vehicle, or comes on and chimes while you are driving, your engine oil level should be checked.
2-67 Cruise Light (If Equipped) The CRUISE light comes on whenever you set your cruise control. Low W asher Light The LOW W ASH light will come on briefly when you turn on the ignition. It will also stay on or come on and chime, if the fluid reservoir is less than one - third full.
2-68 Fuel Gage United States Canada Y our fuel gage tells you about how much fuel you have left, when the ignition is on. When the indicator nears empty , the light, located near the empty symbol, will come on and you will hear a chime. Y ou still have a little fuel left, but you should get more soon.
3- 3-1 Section 3 Comfort Contr ols and Audio Systems In this section, you’ll find out how to operate the comfort control and audio systems offered with your vehicle.
3-2 Comfort Controls This section tells you how to make your air system work for you. W ith this system, you can control the ventilation and heating in your vehicle. Y our vehicle also has the flow - through ventilation system described later in this section.
3-3 (Bi - Level): In this position the air comes through the instrument panel outlets and through the floor outlets. (Floor): In this position most of the air comes through the floor outlets. The rest of the air comes through the windshield and side window outlets.
3-4 Air Conditioning The air conditioner and heater work best if you keep your windows closed while using them. Y our vehicle also has the flow - through ventilation system described later in this section.
3-5 Defogging and Defrosting W indows Y our system has two settings for clearing the front and side windows. For each setting, adjust the temperature control as desired. T o defrost the front window quickly , turn the temperature knob all the way in the red area.
3-6 Rear Window Defogger The rear window defogger button is located on the lower right corner of the control panel. The rear window defogger uses a warming grid to remove fog from the rear window . Press the defogger button to turn the system on. The indicator light will glow .
3-7 V entilation Tips Keep the hood and the area around the windshield wipers free of ice, snow or any other obstruction, such as leaves. The heater and defroster will work far better , reducing the chance of fogging the inside of your windows. Keep the air path under the front seats clear of objects, to help air circulate throughout your vehicle.
3-8 Setting the Clock Press and hold the HR or MN buttons, located below the tune knob, for two seconds. Then press and hold HR until the correct hour appears. AM or PM will appear on the display . Press and hold MN until the correct minute appears. The clock may be set with the ignition on or off.
3-9 AUT O V OL (Automatic V olume): W ith automatic volume, your audio system adjusts automatically to make up for road and wind noise as you drive. Set the volume at the desired level. Press this button to select LOW , MEDIUM or HIGH. A VOL will appear on the display .
3-10 Setting Preset Stations The six numbered pushbuttons let you return to your favorite stations. Y ou can set up to 18 stations (six AM, six FM1 and six FM2) by performing the following steps: 1. T urn the radio on. 2. Press BAND to select AM, FM1 or FM2.
3-1 1 Adjusting the Speakers (Balance/Fade) AUDIO: T o adjust the balance between the right and left speakers, push and release the AUDIO knob until BAL appears on the display . Turn the knob clockwise to move the sound to the right speakers and counterclockwise to move the sound to the left speakers.
3-12 When you are tuned to an RDS station, the station name will appear on the display , instead of the frequency . Most RDS stations provide their station name, the time of day and a Program T ype (PTY) for their current programming. Some stations also provide the name of the current program.
3-13 RDS Messages ALER T!: Alert warns of national or local emergencies. Y ou will not be able to turn off alert announcements. ALER T! appears on the display when an alert announcement plays. When an alert announcement comes on the current radio station, you will hear it, even if the volume is muted or a compact disc is playing.
3-14 When a traffic announcement comes on the current radio station, you will hear it, even if the volume is muted or a compact disc is playing. The traffic symbol and TRAFFIC will appear on the display while the traffic announcement plays.
3-15 4 FWD (Forward): Press and hold this pushbutton to advance quickly within a track. Press and hold this pushbutton for less than two seconds to advance at six times the normal playing speed. Press and hold it for more than two seconds to advance at 17 times the normal playing speed.
3-16 AM-FM Stereo with Cassette T ape and Compact Disc Player with Radio Data System (RDS) and Automatic T one Control (If Equipped) Playing the Radio PWR (Power): Press this knob to turn the system on and off. VOL (V olume): Turn the knob clockwise to increase volume.
3-17 SEEK : Press the right or left arrow to seek to the next or previous station and stay there. The radio will seek to stations with a strong signal only . The sound will mute while seeking. PSCAN (Preset Scan): Press and hold one of the arrows for more than two seconds.
3-18 AUT O T ONE (Automatic): This feature allows you to choose bass and treble equalization settings designed for country/western, jazz, talk, pop, rock and classical stations. Each time you press the AUTO T ONE button, this feature will change to one of the preset equalization settings previously listed.
3-19 RDS features are only available on FM stations that broadcast RDS information. The RDS features of your radio rely on receiving specific RDS information from these stations.
3-20 BAND (Alternate Frequency): Alternate frequency allows the radio to switch to a stronger station with the same program type. Press and hold BAND for two seconds to turn alternate frequency on. AF ON will appear on the display . The radio may switch to stronger stations.
3-21 TRAF (T raffic): Press this button to receive traffic announcements. If the current station does not broadcast traffic announcements, the radio will seek to a station that does. The traffic symbol will flash on the display . When the radio finds a station that broadcasts traffic announcements, it will stop.
3-22 If you want to insert a tape when the ignition is off, first press EJT or DISP . If an error appears on the display , see “Cassette T ape Messages” later in this section. 1 PREV (Previous): Press this pushbutton to go to the previous selection on the tape if the selection has been playing for less than three seconds.
3-23 6 (Dolby): Press this pushbutton to reduce background noise. NR ON will appear on the display . Press it again to turn Dolby B off. NR OFF will appear on the display . Dolby Noise Reduction is manufactured under a license from Dolby Laboratories Licensing Corporation.
3-24 CD Adapter Kits It is possible to use a portable CD player adapter kit with your cassette tape player after disabling the tight/loose tape sensing feature on your tape player . T o disable the feature, use the following steps: 1. T urn the ignition to ON or ACCESSOR Y .
3-25 4 FWD (Forward): Press and hold this pushbutton to advance quickly within a track. Press and hold this pushbutton for less than two seconds to advance at six times the normal playing speed. Press and hold it for more than two seconds to advance at 17 times the normal playing speed.
3-26 Theft-Deterrent Featur e THEFTLOCK is designed to discourage theft of your radio. The feature works automatically by learning a portion of the V ehicle Identification Number (VIN). If the radio is moved to a different vehicle, it will not operate and LOCKED will be displayed.
3-27 NOTICE: Before you add any sound equipment to your vehicle -- like a tape player , CB radio, mobile telephone or two - way radio -- be sure you can add what you want.
3-28 When cleaning the cassette tape player with the recommended non - abrasive cleaning cassette, it is possible that the cassette may eject, because the cut tape detection feature on your radio may recognize it as a broken tape. T o prevent the cleaning cassette from being ejected, use the following steps: 1.
3-29 Care of Y our Compact Discs Handle discs carefully . Store them in their original cases or other protective cases and away from direct sunlight and dust. If the surface of a disc is soiled, dampen a clean, soft cloth in a mild, neutral detergent solution and clean it, wiping from the center to the edge.
4- 4-1 Section 4 Y our Driving and the Road Here you’ll find information about driving on different kinds of roads and in varying weather conditions.
4-2 Defensive Driving The best advice anyone can give about driving is: Drive defensively . Please start with a very important safety device in your vehicle: Buckle up. See “Safety Belts” in the Index. Defensive driving really means “be ready for anything.
4-3 Drunken Driving Death and injury associated with drinking and driving is a national tragedy . It’ s the number one contributor to the highway death toll, claiming thousands of victims every year . Alcohol affects four things that anyone needs to drive a vehicle: Judgment Muscular Coordination V ision Attentiveness.
4-4 It’ s the amount of alcohol that counts. For example, if the same person drank three double martinis (3 ounces or 90 ml of liquor each) within an hour , the person’ s BAC would be close to 0.12 percent. A person who consumes food just before or during drinking will have a somewhat lower BAC level.
4-5 The body takes about an hour to rid itself of the alcohol in one drink. No amount of coffee or number of cold showers will speed that up. “I’ll be careful” isn’t the right answer .
4-6 Control of a V ehicle Y ou have three systems that make your vehicle go where you want it to go. They are the brakes, the steering and the accelerator .
4-7 This is a mistake. Y our brakes may not have time to cool between hard stops. Y our brakes will wear out much faster if you do a lot of heavy braking. If you keep pace with the traffic and allow realistic following distances, you will eliminate a lot of unnecessary braking.
4-8 The anti - lock system can change the brake pressure faster than any driver could. The computer is programmed to make the most of available tire and road conditions. This can help you steer around the obstacle while braking hard. As you brake, your computer keeps receiving updates on wheel speed and controls braking pressure accordingly .
4-9 Steering Power Steering If you lose power steering assist because the engine stops or the system is not functioning, you can steer but it will take much more effort. Steering Tips Driving on Curves It’ s important to take curves at a reasonable speed.
4-10 Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
4-1 1 Off - Road Recovery Y ou may find that your right wheels have dropped off the edge of a road onto the shoulder while you’re driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy .
4-12 Do not get too close to the vehicle you want to pass while you’re awaiting an opportunity . For one thing, following too closely reduces your area of vision, especially if you’re following a larger vehicle. Also, you won’t have adequate space if the vehicle ahead suddenly slows or stops.
4-13 Loss of Control Let’ s review what driving experts say about what happens when the three control systems (brakes, steering and acceleration) don’t have enough friction where the tires meet the road to do what the driver has asked. In any emergency , don’t give up.
4-14 Driving at Night Night driving is more dangerous than day driving. One reason is that some drivers are likely to be impaired -- by alcohol or drugs, with night vision problems, or by fatigue. Here are some tips on night driving. Drive defensively .
4-15 Y ou can be temporarily blinded by approaching headlamps. It can take a second or two, or even several seconds, for your eyes to readjust to the dark. When you are faced with severe glare (as from a driver who doesn’t lower the high beams, or a vehicle with misaimed headlamps), slow down a little.
4-16 The heavier the rain, the harder it is to see. Even if your windshield wiper blades are in good shape, a heavy rain can make it harder to see road signs and traffic signals, pavement markings, the edge of the road and even people walking.
4-17 Hydroplaning doesn’ t happen often. But it can if your tires do not have much tread or if the pressure in one or more is low . It can happen if a lot of water is standing on the road. If you can see reflections from trees, telephone poles or other vehicles, and raindrops “dimple” the water ’ s surface, there could be hydroplaning.
4-18 City Driving One of the biggest problems with city streets is the amount of traffic on them. Y ou’ll want to watch out for what the other drivers are doing and pay attention to traffic signals. Here are ways to increase your safety in city driving: Know the best way to get to where you are going.
4-19 Freeway Driving Mile for mile, freeways (also called thruways, parkways, expressways, turnpikes or superhighways) are the safest of all roads. But they have their own special rules. The most important advice on freeway driving is: Keep up with traffic and keep to the right.
4-20 When you want to leave the freeway , move to the proper lane well in advance. If you miss your exit, do not, under any circumstances, stop and back up. Drive on to the next exit. The exit ramp can be curved, sometimes quite sharply . The exit speed is usually posted.
4-21 Highway Hypnosis Is there actually such a condition as “highway hypnosis”? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever .
4-22 Hill and Mountain Roads Driving on steep hills or mountains is different from driving in flat or rolling terrain. If you drive regularly in steep country , or if you’re planning to visit there, here are some tips that can make your trips safer and more enjoyable.
4-23 CAUTION: Coasting downhill in NEUTRAL (N) or with the ignition off is dangerous. Y our brakes will have to do all the work of slowing down. They could get so hot that they wouldn’t work well. Y ou would then have poor braking or even none going down a hill.
4-24 Winter Driving Here are some tips for winter driving: Have your vehicle in good shape for winter . Y ou may want to put winter emergency supplies in your trunk.
4-25 Driving on Snow or Ice Most of the time, those places where your tires meet the road probably have good traction. However , if there is snow or ice between your tires and the road, you can have a very slippery situation. Y ou’ll have a lot less traction or “grip” and will need to be very careful.
4-26 If Y ou’re Caught in a Blizzard If you are stopped by heavy snow , you could be in a serious situation. Y ou should probably stay with your vehicle unless you know for sure that you are near help and you can hike through the snow .
4-27 CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. Y ou can’t see it or smell it, so you might not know it is in your vehicle. Clear away snow from around the base of your vehicle, especially any that is blocking your exhaust pipe.
4-28 Recreational V ehicle T owing Recreational vehicle towing means towing your vehicle behind another vehicle -- such as behind a motorhome. The two most common types of recreational vehicle towing .
4-29 Dinghy T owing T o tow your vehicle with all four wheels on the ground, follow these steps: 1. Position the vehicle to tow and then secure it. 2. T urn the ignition switch to OFF .
4-30 NOTICE: Make sur e that the towing speed does not exceed 65 mph (1 10 km/h), or your vehicle could be badly damaged. NOTICE: Do not tow your vehicle from the r ear . Y our vehicle could be badly damaged and the repairs would not be covered by your warranty .
4-31 Dolly T owing T o tow your vehicle with a dolly and two wheels on the ground, follow these steps: 1. Put the front wheels on a dolly . 2. Put the vehicle in P ARK (P). 3. Set the parking brake and then remove the key . 4. Clamp the steering wheel in a straight - ahead position with a clamping device designed for towing.
4-32 Loading Y our V ehicle T wo labels on your vehicle show how much weight it may properly carry . The Tire - Loading Information label found on the rear edge of the driver ’ s side door tells you the proper size, speed rating and recommended inflation pressures for the tires on your vehicle.
4-33 CAUTION: Do not load your vehicle any heavier than the GVWR, or either the maximum front or r ear GA WR. If you do, parts on your vehicle can break, and it can change the way your vehicle handles. These could cause you to lose control and crash. Also, overloading can shorten the life of your vehicle.
4-34 T owing a T railer CAUTION: If you don’t use the correct equipment and drive properly , you can lose control when you pull a trailer . For example, if the trailer is too heavy , the brakes may not work well -- or even at all. Y ou and your passengers could be seriously injured.
4-35 If Y ou Do Decide T o Pull A T railer If you do, here are some important points: There are many different laws, including speed limit restrictions, having to do with trailering. Make sure your rig will be legal, not only where you live but also where you’ll be driving.
4-36 W eight of the T railer T ongue The tongue load (A) of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle. The Gross V ehicle W eight (GVW) includes the curb weight of the vehicle, any cargo you may carry in it, and the people who will be riding in the vehicle.
4-37 Hitches It’ s important to have the correct hitch equipment. Crosswinds, lar ge trucks going by and rough roads are a few reasons why you’ll need the right hitch. Here are some rules to follow: The rear bumper on your vehicle is not intended for hitches.
4-38 Driving with a T railer T owing a trailer requires a certain amount of experience. Before setting out for the open road, you’ll want to get to know your rig. Acquaint yourself with the feel of handling and braking with the added weight of the trailer .
4-39 Making T urns NOTICE: Making very sharp turns while trailering could cause the trailer to come in contact with the vehicle. Y our vehicle could be damaged. A void making very sharp turns while trailering. When you’re turning with a trailer , make wider turns than normal.
4-40 Driving On Grades NOTICE: Do not tow on steep continuous grades exceeding 6 miles (9.6 km). Extended, higher than normal engine and transaxle temperatures may r esult and damage your vehicle. Frequent stops ar e very important to allow the engine and transaxle to cool.
4-41 When Y ou Are Ready to Leave After Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you: start your engine, shift into a gear , and release the parking brake. 2. Let up on the brake pedal. 3. Drive slowly until the trailer is clear of the chocks.
5- 5-1 Section 5 Pr oblems on the Road Here you’ll find what to do about some problems that can occur on the road. 5 - 2 Hazard W arning Flashers 5 - 2 Other W arning Devices 5 - 3 Jump Starting 5 -.
5-2 Hazard W arning Flashers Y our hazard warning flashers let you warn others. They also let police know you have a problem. Y our front and rear turn signal lamps will flash on and off. The hazard warning flasher is located near the center of the instrument panel.
5-3 Jump Starting If your battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to follow the steps below to do it safely . CAUTION: Batteries can hurt you. They can be dangerous because: They contain acid that can burn you.
5-4 2. Get the vehicles close enough so the jumper cables can reach, but be sure the vehicles aren’t touching each other . If they are, it could cause a ground connection you don’t want. Y ou wouldn’t be able to start your vehicle, and the bad grounding could damage the electrical systems.
5-5 CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Be sur e the battery has enough water . Y ou don’t need to add water to the ACDelco battery installed in every new GM vehicle.
5-6 6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery . Use a remote positive (+) terminal if the vehicle has one. 7. Don’t let the other end touch metal. Connect it to the positive (+) terminal of the good battery .
5-7 8. Now connect the black negative ( - ) cable to the negative ( - ) terminal of the good battery . Use a remote negative ( - ) terminal if the vehicle has one. Don’t let the other end touch anything until the next step. The other end of the negative ( - ) cable doesn’ t go to the dead battery .
5-8 10. Now start the vehicle with the good battery and run the engine for a while. 1 1. Try to start the vehicle that had the dead battery . If it won’t start after a few tries, it probably needs service. NOTICE: Damage to your vehicle may result fr om electrical shorting if jumper cables are r emoved incorrectly .
5-9 T o disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative ( - ) cable from the vehicle that had the dead battery . 2. Disconnect the black negative ( - ) cable from the vehicle with the good battery . 3.
5-10 If Steam Is Coming From Y our Engine CAUTION: Steam from an overheated engine can burn you badly , even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down.
5-1 1 If No Steam Is Coming From Y our Engine An overheat warning, along with a low coolant light, can indicate a serious problem. See “Low Coolant Light” in the Index. If you get an engine overheat warning with no low coolant light, but see or hear no steam, the problem may not be too serious.
5-12 Cooling System When you decide it’ s safe to lift the hood, here’ s what you’ll see: A. Electric Engine Cooling Fans B. Coolant Surge T ank with Pressure Cap CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you.
5-13 The coolant level should be at or above the FULL COLD mark. If it isn’t, you may have a leak at the pressure cap or in the radiator hoses, heater hoses, radiator , water pump or somewhere else in the cooling system. CAUTION: Heater and radiator hoses, and other engine parts, can be very hot.
5-14 How to Add Coolant to the Coolant Surge T ank NOTICE: This vehicle has a specific coolant fill pr ocedur e. Failure to follow this pr ocedure could cause your engine to overheat and be severely damaged. If you haven’t found a problem yet, check to see if coolant is visible in the surge tank.
5-15 CAUTION: Adding only plain water to your cooling system can be dangerous. Plain water , or some other liquid such as alcohol, can boil before the pr oper coolant mixture will. Y our vehicle’ s coolant warning system is set for the proper coolant mixture.
5-16 1. Park the vehicle on a level surface. Y ou can remove the coolant surge tank pressure cap when the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot. T urn the pressure cap slowly counterclockwise (left) about two or two and one - half turns.
5-17 3. Then fill the coolant surge tank with the proper mixture, to the hash mark on the label. W ait about five minutes, then check to see if the level is below the hash mark. If the level is below the hash mark, add additional coolant to bring the level up to the hash mark.
5-18 If a Tir e Goes Flat It’ s unusual for a tire to “blow out” while you’re driving, especially if you maintain your tires properly . If air goes out of a tire, it’ s much more likely to leak out slowly .
5-19 The following steps will tell you how to use the jack and change a tire. Removing the Spare T ire and T ools The equipment you’ll need is in the trunk. 1. T urn the center retainer nut on the compact spare tire cover counterclockwise to remove it.
5-20 3. T urn the wing nut counterclockwise and remove it. Then lift off the adapter and remove the compact spare tire. See “Compact Spare T ire” later in this section for more information about the compact spare tire. 4. Remove the jack and wrench from the trunk.
5-21 Removing the Flat Tir e and Installing the Spare Tir e 1. If your vehicle is equipped with a wheel cover or hubcap that has plastic wheel nut caps, then loosen the plastic nut caps (you may need to use the wheel wrench to loosen them). Do not pry off wheel covers or center caps that have plastic wheel nut caps.
5-22 4. Then use the wrench to loosen all the wheel nuts. Don’t remove them yet. 5. Position the jack and raise the jack head until it fits firmly into the notch in the vehicle’ s frame nearest the flat tire.
5-23 CAUTION: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. CAUTION: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall.
5-24 9. Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel. CAUTION: Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and cause an accident.
5-25 CAUTION: Never use oil or grease on studs or nuts. If you do, the nuts might come loose. Y our wheel could fall off, causing a serious accident. 10. Install the compact spare tire. Put the wheel nuts back on with the cone end of the nuts toward the wheel.
5-26 12. T ighten the wheel nuts firmly in a crisscross sequence, as shown. CAUTION: Incorr ect wheel nuts or impr operly tightened wheel nuts can cause the wheel to become loose and even come off. This could lead to an accident. Be sure to use the corr ect wheel nuts.
5-27 Storing the Flat Tir e and T ools CAUTION: Storing a jack, a tire or other equipment in the passenger compartment of the vehicle could cause injury . In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
5-28 Storing the Spare T ire and T ools CAUTION: Storing a jack, a tire or other equipment in the passenger compartment of the vehicle could cause injury . In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
5-29 Compact Spare T ire Although the compact spare tire was fully inflated when your vehicle was new , it can lose air after a time. Check the inflation pressure regularly . It should be 60 psi (420 kPa). After installing the compact spare on your vehicle, you should stop as soon as possible and make sure your spare tire is correctly inflated.
5-30 If Y ou’re Stuck: In Sand, Mud, Ice or Snow In order to free your vehicle when it is stuck, you will need to spin the wheels, but you don’t want to spin your wheels too fast. The method known as “rocking” can help you get out when you’re stuck, but you must use caution.
6- 6-1 Section 6 Service and Appearance Car e Here you will find information about the care of your vehicle. This section begins with service and fuel information, and then it shows how to check important fluid and lubricant levels. There is also technical information about your vehicle, and a part devoted to its appearance care.
6-2 Service Y our dealer knows your vehicle best and wants you to be happy with it. W e hope you’ll go to your dealer for all your service needs. Y ou’ll get genuine GM parts and GM - trained and supported service people. W e hope you’ll want to keep your GM vehicle all GM.
6-3 CAUTION: Y ou can be injured and your vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. Be sure you have sufficient knowledge, experience, the proper r eplacement parts and tools before you attempt any vehicle maintenance task.
6-4 Gasoline Specifications It is recommended that gasoline meet specifications which were developed by the American Automobile Manufacturers Association and endorsed by the Canadian V ehicle Manufacturers’ Association for better vehicle performance and engine protection.
6-5 Additives Some gasolines that are not reformulated for low emissions may contain an octane - enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT); ask the attendant where you buy gasoline whether the fuel contains MMT . General Motors does not recommend the use of such gasolines.
6-6 Filling Y our T ank CAUTION: Gasoline vapor is highly flammable. It burns violently , and that can cause very bad injuries. Don’t smoke if you’re near gasoline or r efueling your vehicle. Keep sparks, flames and smoking materials away from gasoline.
6-7 While refueling, hang the tethered fuel cap inside the fuel door . T o remove the fuel cap, turn it slowly to the left (counterclockwise). The fuel cap has a spring in it; if you let go of the cap too soon, it will spring back to the right. CAUTION: If you get gasoline on yourself and then something ignites it, you could be badly burned.
6-8 When you put the fuel cap back on, turn it to the right (clockwise) until you hear a clicking sound. Make sure you fully install the cap. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere.
6-9 Checking Things Under the Hood CAUTION: An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing and tools away from any underhood electric fan. CAUTION: Things that burn can get on hot engine parts and start a fire.
6-10 2. Then go to the front of the vehicle and lift the secondary hood release handle before lifting the hood. 3. Lift the hood. 4. Release the hood prop rod from its retainer and put the hood prop into the slot marked PROP ROD. Before closing the hood, be sure all the filler caps are on properly .
6-1 1 Engine Compartment Overview When you open the hood, you’ll see the following: A. Engine Coolant Surge T ank B. Power Steering Fluid Reservoir C. Engine Oil Fill Cap D. Engine Oil Dipstick E. Brake Fluid Reservoir F . Engine Compartment Fuse Block G.
6-12 Engine Oil If the CHECK OIL light appears on the instrument cluster , it means you need to check your engine oil level right away . For more information, see “Check Oil Light” in the Index. Y ou should check your engine oil level regularly; this is an added reminder .
6-13 When to Add Engine Oil If the oil is at or below the ADD line, then you’ll need to add at least one quart of oil. But you must use the right kind. This part explains what kind of oil to use. For engine oil crankcase capacity , see “Capacities and Specifications” in the Index.
6-14 What Kind of Engine Oil to Use Oils recommended for your vehicle can be identified by looking for the starburst symbol. This symbol indicates that the oil has been certified by the American Petroleum Institute (API). Do not use any oil which does not carry this starburst symbol.
6-15 As in the chart shown previously , SAE 5W - 30 is best for your vehicle. However , you can use SAE 10W - 30 if it’ s going to be 0 F ( - 18 C) or above. These numbers on an oil container show its viscosity , or thickness. Do not use other viscosity oils, such as SAE 20W - 50.
6-16 If none of them is true, use the long trip/highway maintenance schedule. Change the oil and filter every 7,500 miles (12 500 km) or 12 months -- whichever occurs first. Driving a vehicle with a fully warmed engine under highway conditions will cause engine oil to break down slower .
6-17 T o check or replace the engine air cleaner/filter: 1. Remove the four screws on the cover , then pull the cover back. 2. Remove the engine air cleaner/filter and check or replace it. 3. Replace the cover tightly . Refer to the Maintenance Schedule to determine when to replace the air filter .
6-18 Change both the fluid and filter every 50,000 miles (83 000 km) if the vehicle is mainly driven under one or more of these conditions: In heavy city traffic where the outside temperature regularly reaches 90 F (32 C) or higher . In hilly or mountainous terrain.
6-19 NOTICE: When adding coolant, it is important that you use only DEX - COOL (silicate - free) coolant. If coolant other than DEX - COOL is added to the system, prematur e engine, heater core or radiator corr osion may r esult.
6-20 NOTICE: If you use an improper coolant mixtur e, your engine could overheat and be badly damaged. The repair cost wouldn’t be cover ed by your warranty . T oo much water in the mixture can freeze and crack the engine, radiator , heater core and other parts.
6-21 CAUTION: T urning the surge tank pressur e cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly . Never turn the surge tank pressur e cap -- even a little -- when the engine and radiator are hot.
6-22 Surge T ank Pressur e Cap NOTICE: Y our pressure cap is a 15 psi (105 kPa) pressur e - type cap and must be tightly installed to prevent coolant loss and possible engine damage from overheating.
6-23 Windshield W asher Fluid What to Use When you need windshield washer fluid, be sure to read the manufacturer ’ s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a fluid that has sufficient protection against freezing.
6-24 Brakes Brake Fluid Y our brake master cylinder reservoir is on the driver ’ s side of the engine compartment. It is filled with DOT - 3 brake fluid. See “Engine Compartment Overview” in the Index. There are only two reasons why the brake fluid level in the reservoir might go down.
6-25 United States Canada When your brake fluid falls to a low level, your brake warning light will come on. See “Brake System W arning Light” in the Index. What to Add When you do need brake fluid, use only DOT - 3 brake fluid. Use new brake fluid from a sealed container only .
6-26 Brake W ear Y our vehicle has front disc brakes and rear drum brakes. Disc brake pads have built - in wear indicators that make a high - pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving (except when you are pushing on the brake pedal firmly).
6-27 Brake Pedal T ravel See your dealer if the brake pedal does not return to normal height, or if there is a rapid increase in pedal travel. This could be a sign of brake trouble. Brake Adjustment Every time you make a moderate brake stop, your disc brakes adjust for wear .
6-28 Battery Y our new vehicle comes with a maintenance free ACDelco battery . When it’ s time for a new battery , get one that has the replacement number shown on the original battery’ s label. W e recommend an ACDelco battery . See “Engine Compartment Overview” in the Index for battery location.
6-29 Bulb Replacement For bulb types, see “Replacement Bulbs” in the Index. For any bulb changing procedures not listed in this section, contact your dealer . Halogen Bulbs CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb.
6-30 1. Carefully pull directly up on the two latches to unhook the lamp assembly . 2. Remove the lamp assembly from the vehicle by pulling it forward. Use care not to scratch the vehicle with the lamp or the lamp with the fender . 3. Unclip the wiring harness and twist the socket less than a on e - quarter turn counterclockwise and remove it.
6-31 Front T urn Signal Lamps 1. Remove the headlamp assembly as described in “Headlamps.” 2. Once it has been removed, press the tab on the white socket while twisting it less than one - quarter turn counterclockwise and pull it out. 3. Remove the old bulb and replace it with a new one.
6-32 T urn Signal/T ail/Stop/Back-Up Lamps A. Rear T urn Signal Lamp B. T aillamp/Stoplamp C. Back - Up Lamp 1. Unscrew the fastener located on the inside of the trunk at the rear of the vehicle. 2. Gently pull back the trunk trim. 3. Remove the three plastic wing nuts.
6-33 4. Pull out the taillamp assembly to expose the backplate. 5. Carefully remove the backplate by gently pulling up on the two upper and two lower tabs. 6. Gently wiggle the bulb to remove it from the socket. Replace the bulb. 7. Reverse the steps to reassemble the backplate and attach the taillamp assembly to the vehicle.
6-34 Windshield W iper Blade Replacement W indshield wiper blades should be inspected at least twice a year for wear and cracking. See “W iper Blade Check” in the Index for more information. For the proper type and length, see “Capacities and Specifications” in the Index.
6-35 Tire s Y our new vehicle comes with high - quality tires made by a leading tire manufacturer . If you ever have questions about your tire warranty and where to obtain service, see your Chevrolet W arranty booklet for details. CAUTION: Poorly maintained and improperly used tir es are danger ous.
6-36 Inflation -- Tir e Pressur e The T ire - Loading Information label, which is located on the driver ’ s side rear passenger door , shows the correct inflation pressures for your tires when they’re cold. “Cold” means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.
6-37 Tir e Inspection and Rotation T ires should be rotated every 6,000 to 8,000 miles (10 000 to 13 000 km). Any time you notice unusual wear , rotate your tires as soon as possible and check wheel alignment.
6-38 When It’ s Time for New T ires One way to tell when it’ s time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining. Y ou need a new tire if any of the following statements are true: Y ou can see the indicators at three or more places around the tire.
6-39 Buying New Tir es T o find out what kind and size of tires you need, look at the T ire - Loading Information label. The tires installed on your vehicle when it was new had a T ire Performance Criteria Specification (TPC Spec) number on each tire’ s sidewall.
6-40 Uniform Tir e Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: T readwear 200 T raction AA T empera.
6-41 T emperature -- A, B, C The temperature grades are A (the highest), B, and C, representing the tire’ s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
6-42 Each new wheel should have the same load - carrying capacity , diameter , width, offset and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new GM original equipment parts.
6-43 T ire Chains NOTICE: Use tire chains only wher e legal and only when you must. Use only SAE Class “S” type chains that are the pr oper size for your tires. Install them on the front tir es and tighten them as tightly as possible with the ends securely fastened.
6-44 Don’t use any of these unless this manual says you can. In many uses, these will damage your vehicle: Alcohol Laundry Soap Bleach Reducing Agents Cleaning the Inside of Y our V ehicle Use a vacuum cleaner often to get rid of dust and loose dirt.
6-45 Special Fabric Cleaning Problems Stains caused by such things as catsup, coffee (black), egg, fruit, fruit juice, milk, soft drinks, vomit, urine and blood can be removed as follows: 1. Carefully scrape off excess stain, then sponge the soiled area with cool water .
6-46 Cleaning the T op of the Instrument Panel Use only mild soap and water to clean the top surfaces of the instrument panel. Sprays containing silicones or waxes may cause annoying reflections in the windshield and even make it difficult to see through the windshield under certain conditions.
6-47 Cleaning the Outside of the Windshield and W iper Blades If the windshield is not clear after using the windshield washer , or if the wiper blade chatters when running, wax, sap or other material may be on the blade or windshield. Clean the outside of the windshield with a full - strength glass cleaning liquid.
6-48 Cleaning Exterior Lamps/Lenses Use only lukewarm or cold water , a soft cloth and a car washing soap to clean exterior lamps and lenses. Follow instructions under “W ashing Y our V ehicle.” Finish Care Occasional waxing or mild polishing of your vehicle by hand may be necessary to remove residue from the paint finish.
6-49 Cleaning Aluminum Wheels (If Equipped) Keep your wheels clean using a soft clean cloth with mild soap and water . Rinse with clean water . After rinsing thoroughly , dry with a soft clean towel. A wax may then be applied. The surface of these wheels is similar to the painted surface of your vehicle.
6-50 Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away . Minor chips and scratches can be repaired with touch - up materials available from your dealer or other service outlets. Larger areas of finish damage can be corrected in your dealer ’ s body and paint shop.
6-51 GM V ehicle Care/Appearance Materials.
6-52 V ehicle Identification Number (VIN) This is the legal identifier for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver ’ s side. Y ou can see it if you look through the windshield from outside your vehicle.
6-53 Electrical System Add-On Electrical Equipment NOTICE: Don’t add anything electrical to your vehicle unless you check with your dealer first. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty .
6-54 Fuses and Circuit Br eakers The wiring circuits in your vehicle are protected from short circuits by a combination of fuses, circuit breakers and fusible thermal links in the wiring itself. Look at the silver - colored band inside the fuse. If the band is broken or melted, replace the fuse.
6-55 Instrument Panel Fuse Block -- Driver’s Side Fuse Usage A W ipers B T runk Release and Remote Keyless Entry C T urn Signals D Power Mirrors E Air Bag F Body Function Control Module Fuse Usage G.
6-56 Instrument Panel Fuse Block -- Passenger’s Side Fuse Usage A Instrument Panel Lights, Brightness Control B Cruise Control Switches C Climate Control System D Cruise Control E Fog Lamps F Interi.
6-57 Engine Compartment Fuse Block The engine compartment fuse block is located on the driver ’ s side of the vehicle, near the engine air cleaner/filter .
6-58 Mirco Relay Usage 16 Air Conditioning Compressor 17 Not Used 18 Fuel Pump 19 Automatic Light Control 20 Automatic Light Control 21 Horn 22 Daytime Running Lamps (DRL) Minifuse Usage 23 - 32 Spare.
6-59 Minifuse Usage 48 Fuel Pump Injectors 49 Not Used 50 Right Headlamp 51 Left Headlamp 52 Cooling Fan 53 HV AC Blower (Climate Control) 54 Not Used 55 Cooling Fan #2 Ground 56 Fuse Puller 57 Not Used Replacement Bulbs Exterior Lamp Bulb . . . . . .
6-60 Capacities and Specifications The following approximate capacities are given in English and metric conversions. Please refer to “Recommended Fluids and Lubricants” in the Index for more information. Capacities Automatic T ransaxle Complete Overhaul 9.
7- 7-1 Section 7 Maintenance Schedule This section covers the maintenance required for your vehicle. Y our vehicle needs these services to retain its safety , dependability and emission control performance.
7-2 Have you pur chased the GM Pr otection Plan? The Plan supplements your new vehicle warranties. See your W arranty and Owner Assistance booklet or your dealer for details. Introduction Y our V ehicle and the Envir onment Proper vehicle maintenance not only helps to keep your vehicle in good working condition, but also helps the environment.
7-3 How This Section is Organized This maintenance schedule is divided into five parts: “Part A: Scheduled Maintenance Services” explains what to have done and how often.
7-4 Part A: Scheduled Maintenance Services Using Y our Maintenance Schedule W e at General Motors want to help you keep your vehicle in good working condition. But we don’t know exactly how you’ll drive it. Y ou may drive very short distances only a few times a week.
Scheduled Maintenance 7-5 Short T rip/City Definition Follow the Short T rip/City Scheduled Maintenance if any one of these conditions is true for your vehicle: Most trips are less than 5 miles (8 km). This is particularly important when outside temperatures are below freezing.
Scheduled Maintenance 7-6 Long T rip/Highway Definition Follow this scheduled maintenance only if none of the conditions from the Short T rip/City Scheduled Maintenance are true. Do not use this schedule if the vehicle is used for trailer towing, driven in a dusty area or used off paved roads.
Short T rip/City Scheduled Maintenance 7-7 The services shown in this schedule up to 100,000 miles (166 000 km) should be repeated after 100,000 miles (166 000 km) at the same intervals for the life of this vehicle.
Short T rip/City Scheduled Maintenance 7-8 3,000 Miles (5 000 km) Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Contr ol Service. 6,000 Miles (10 000 km) Change engine oil and filter (or every 3 months, whichever occurs first).
Short T rip/City Scheduled Maintenance 7-9 15,000 Miles (25 000 km) Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Contr ol Service. Inspect engine air cleaner filter if you are driving in dusty conditions. Replace filter if necessary .
Short T rip/City Scheduled Maintenance 7-10 24,000 Miles (40 000 km) Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Contr ol Service. Rotate tires. See “T ire Inspection and Rotation” in the Index for proper rotation pattern and additional information.
Short T rip/City Scheduled Maintenance 7-1 1 33,000 Miles (55 000 km) Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Contr ol Service. 36,000 Miles (60 000 km) Change engine oil and filter (or every 3 months, whichever occurs first).
Short T rip/City Scheduled Maintenance 7-12 45,000 Miles (75 000 km) Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Contr ol Service. Inspect engine air cleaner filter if you are driving in dusty conditions. Replace filter if necessary .
Short T rip/City Scheduled Maintenance 7-13 51,000 Miles (85 000 km) Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Contr ol Service. 54,000 Miles (90 000 km) Change engine oil and filter (or every 3 months, whichever occurs first).
Short T rip/City Scheduled Maintenance 7-14 60,000 Miles (100 000 km) Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Contr ol Service. Inspect engine accessory drive belt. An Emission Contr ol Service. Replace engine air cleaner filter .
Short T rip/City Scheduled Maintenance 7-15 69,000 Miles (1 15 000 km) Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Contr ol Service. 72,000 Miles (120 000 km) Change engine oil and filter (or every 3 months, whichever occurs first).
Short T rip/City Scheduled Maintenance 7-16 81,000 Miles (135 000 km) Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Contr ol Service. 84,000 Miles (140 000 km) Change engine oil and filter (or every 3 months, whichever occurs first).
Short T rip/City Scheduled Maintenance 7-17 93,000 Miles (155 000 km) Change engine oil and filter (or every 3 months, whichever occurs first). An Emission Contr ol Service. 96,000 Miles (160 000 km) Change engine oil and filter (or every 3 months, whichever occurs first).
Short T rip/City Scheduled Maintenance 7-18 100,000 Miles (166 000 km) Inspect spark plug wires. An Emission Contr ol Service. Replace spark plugs. An Emission Contr ol Service.
Long T rip/Highway Scheduled Maintenance 7-19 The services shown in this schedule up to 100,000 miles (166 000 km) should be repeated after 100,000 miles (166 000 km) at the same intervals for the life of this vehicle.
Long T rip/Highway Scheduled Maintenance 7-20 7,500 Miles (12 500 km) Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Contr ol Service. Rotate tires. See “T ire Inspection and Rotation” in the Index for proper rotation pattern and additional information.
Long T rip/Highway Scheduled Maintenance 7-21 30,000 Miles (50 000 km) Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Contr ol Service. Rotate tires. See “T ire Inspection and Rotation” in the Index for proper rotation pattern and additional information.
Long T rip/Highway Scheduled Maintenance 7-22 50,000 Miles (83 000 km) Change automatic transaxle fluid and filter if the vehicle is mainly driven under one or more of these conditions: – In heavy city traf fic where the outside temperature regularly reaches 90 F (32 C) or higher .
Long T rip/Highway Scheduled Maintenance 7-23 60,000 Miles (100 000 km) Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Contr ol Service. Rotate tires. See “T ire Inspection and Rotation” in the Index for proper rotation pattern and additional information.
Long T rip/Highway Scheduled Maintenance 7-24 82,500 Miles (137 500 km) Change engine oil and filter (or every 12 months, whichever occurs first). An Emission Contr ol Service. Rotate tires. See “T ire Inspection and Rotation” in the Index for proper rotation pattern and additional information.
Long T rip/Highway Scheduled Maintenance 7-25 100,000 Miles (166 000 km) Inspect spark plug wires. An Emission Contr ol Service. Replace spark plugs. An Emission Contr ol Service.
7-26 Part B: Owner Checks and Services Listed in this part are owner checks and services which should be performed at the intervals specified to help ensure the safety , dependability and emission control performance of your vehicle. Be sure any necessary repairs are completed at once.
7-27 At Least T wice a Y ear Restraint System Check Make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly . Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired.
7-28 At Least Once a Y ear Key Lock Cylinders Service Lubricate the key lock cylinders with the lubricant specified in Part D. Body Lubrication Service Lubricate all the body door hinges and latches, including those for the hood and the trunk lid. Part D tells you what to use.
7-29 Automatic T ransaxle Shift Lock Control System Check CAUTION: When you are doing this check, the vehicle could move suddenly . If it does, you or others could be injured. Follow the steps below . 1. Before you start, be sure you have enough room around the vehicle.
7-30 Parking Brake and Automatic T ransaxle P ARK (P) Mechanism Check CAUTION: When you are doing this check, your vehicle could begin to move. Y ou or others could be injured and pr operty could be damaged. Make sure ther e is room in fr ont of your vehicle in case it begins to roll.
7-31 Part C: Periodic Maintenance Inspections Listed in this part are inspections and services which should be performed at least twice a year (for instance, each spring and fall). Y ou should let your dealer ’ s service department or other qualified service center do these jobs.
7-32 Fuel System Inspection Inspect the complete fuel system for damage or leaks. Engine Cooling System Inspection Inspect the hoses and have them replaced if they are cracked, swollen or deteriorated. Inspect all pipes, fittings and clamps; replace as needed.
7-33 Part D: Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number or specification may be obtained from your dealer . USAGE FLUID/LUBRICANT Engine Oil Engine oil with the American Petroleum Institute Certified for Gasoline Engines starburst symbol of the proper viscosity .
7-34 USAGE FLUID/LUBRICANT Key Lock Cylinders Multi - Purpose Lubricant, Superlube (GM Part No. 12346241 or equivalent). Hood Latch Assembly , Secondary Latch, Pivots, Spring Anchor and Release Pawl Lubriplate Lubricant Aerosol (GM Part No. 12346293 or equivalent) or lubricant meeting requirements of NLGI # 2, Category LB or GC - LB.
7-35 Part E: Maintenance Record After the scheduled services are performed, record the date, odometer reading and who performed the service in the boxes provided after the maintenance interval. Any additional information from “Owner Checks and Services” or “Periodic Maintenance” can be added on the following record pages.
7-36 Maintenance Record DA TE ODOMETER READING SER VICED BY MAINTENANCE PERFORMED.
7-37 Maintenance Record DA TE ODOMETER READING SER VICED BY MAINTENANCE PERFORMED.
7-38 Maintenance Record DA TE ODOMETER READING SER VICED BY MAINTENANCE PERFORMED.
8- 8-1 Section 8 Customer Assistance Information Here you will find out how to contact Chevrolet if you need assistance. This section also tells you how to obtain service publications and how to report any safety defects.
8-2 Customer Satisfaction Procedur e Y our satisfaction and goodwill are important to your dealer and to Chevrolet. Normally , any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer ’ s sales or service departments.
8-3 STEP TWO -- If after contacting a member of dealership management, it appears your concern cannot be resolved by the dealership without further help, contact the Chevrolet Customer Assistance Center by calling 1-800-222-1020.
8-4 Y ou may contact the BBB using the toll - free telephone number or write them at the following address: BBB Auto Line Council of Better Business Bureaus, Inc. 4200 W ilson Boulevard Suite 800 Arlington, V A 22203 - 1804 T elephone: 1 - 800 - 955 - 5100 This program is available in all 50 states and the District of Columbia.
8-5 Canada General Motors of Canada Limited Customer Communication Centre, 163-005 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 1-800-263-3777 (English) 1-800-263-7854 (French) 1-800-263-3830 (For T ext T elephone devices (TTYs)) Roadside Assistance: 1-800-268-6800 All Overseas Locations Please contact the local General Motors Business Unit.
8-6 Chevrolet Roadside Assistance Program T o enhance Chevrolet’ s strong commitment to customer satisfaction, Chevrolet is excited to announce the establishment of the Chevrolet Roadside Assistance Center . As the owner of a 2002 Chevrolet, membership in Roadside Assistance is free.
8-7 Roadside Courtesy Car e provides: Roadside Basic Car e services (as outlined previously) Plus: FREE Non - W arranty T owing (to the closest dealer from a legal roadway) FREE Locksmith/Key Service .
8-8 For prompt assistance when calling, please have the following available to give to the advisor: V ehicle Identification Number (VIN) License plate number V ehicle color V ehicle location T elephon.
8-9 If the dealer requests that you simply drop the vehicle off for service, you are ur ged to do so as early in the work day as possible to allow for same day repair . T ransportation Options W arranty service can generally be completed while you wait.
8-10 Courtesy T ransportation is available only at participating dealers and all program options, such as shuttle service, may not be available at every dealer . Please contact your dealer for specific information about availability . All Courtesy T ransportation arrangements will be administered by appropriate dealer personnel.
8-1 1 REPOR TING SAFETY DEFECTS TO THE CANADIAN GOVERNMENT If you live in Canada, and you believe that your vehicle has a safety defect, you should immediately notify T ransport Canada, in addition to notifying General Motors of Canada Limited.
8-12 SER VICE PUBLICA TIONS ORDERING INFORMA TION Service Manuals Service Manuals have the diagnosis and repair information on engines, transmission, axle, suspension, brakes, electrical, steering, body , etc.
An important point after buying a device Chevrolet 22675723 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Chevrolet 22675723 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Chevrolet 22675723 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Chevrolet 22675723 you will learn all the available features of the product, as well as information on its operation. The information that you get Chevrolet 22675723 will certainly help you make a decision on the purchase.
If you already are a holder of Chevrolet 22675723, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Chevrolet 22675723.
However, one of the most important roles played by the user manual is to help in solving problems with Chevrolet 22675723. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Chevrolet 22675723 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
