Instruction/ maintenance manual of the product 2010 HHR Chevrolet
Go to page of 476
2010 Chevrolet HHR Owner Manual M In Brief ................ .......... ........... ....... 1 - 1 I n s t r u m e n t P a n e l ... .............................. 1 - 2 Initial Drive Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 V ehicle Features .
2010 Chevrolet HHR Owner Manual M Appearance Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 1 1 V ehicle Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 18 Electrical System . . . . . . . . . . . . . . . .
GENERAL MOTORS, GM, the GM Emblem, CHEVROLET , the CHEVROLET Emblem, and the name HHR are registered trademarks of General Motors. This manual describes features that may or may not be on your specific vehicle either because they are options that you did not purchase or due to changes subsequent to the printing of this owner manual.
Safety W arnings and Symbols W arning messages found on vehicle labels and in this manual describe hazards and what to do to avoid or reduce them. Danger indicates a hazard with a high level of risk which will result in serious injury or death. W arning or Caution indicates a hazard that could result in injury or death.
V ehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index. 9 : Airbag Readiness Light # : Air Conditioning ! : Antilock Brake System (ABS) g : Audio Steering Wheel Controls or OnStar ® $ : Brake System Warning Light " : Charging System I : Cruise Control B : Engine Coolant T emperature O : Exterior Lamps # : Fog Lamps .
2 NOTES vi.
Section 1 In Brief Instrument Panel ................................... 1-2 Initial Drive Information .. ....... .................. 1-4 Remote Keyless Entry (RKE) System . . . . . . . . . . . 1-4 Remote V ehicle Start . . . . . . . . . . . . . . . . .
Instrument Panel 1-2.
A. Outlet Adjustment on page 4 ‑ 21 . B. Cruise Control on page 4 ‑ 8 (If Equipped). C. T urn Signal/Multifunction Lever on page 4 ‑ 4 . D. Instrument Panel Cluster on page 4 ‑ 24 . E. Windshield Wipers on page 4 ‑ 5 and Windshield Washer on page 4 ‑ 6 .
Initial Drive Information This section provides a brief overview about some of the important features that may or may not be on your specific vehicle. For more detailed information, refer to each of the features which can be found later in this owner manual.
When the vehicle starts, the parking lamps will turn on and remain on as long as the engine is running. The doors will be locked and the climate control system may come on. The engine will continue to run for 10 minutes. Repeat the steps for a 10-minute time extension.
Windows On vehicles with power windows, the switches are on each of the side doors. The driver door also has switches that control the passenger and rear windows. Press the front of the switch to lower the window . Pull the switch up to raise it. For more information, see Power Windows on page 3 ‑ 17 .
Power Seats Move the seat forward or rearward by moving the control forward or rearward. Raise or lower the front of the seat, or the entire seat, by moving the front or rear of the control up or down. See Power Seat on page 2 ‑ 5 . Reclining Seatbacks 1.
Power Lumbar Press the front or rear of the control to increase or decrease lumbar support. See Power Lumbar on page 2 ‑ 6 . Second Row Seats The seatbacks can be folded flat. For detailed instructions for lowering the seatback(s), see Split Folding Rear Seat on page 2 ‑ 1 1 .
Heated Seats On vehicles with this feature, the controls are located on the climate control panel. Press the button to turn the heated seat on to the high setting, a second time to go to the low setting, and a third to turn it off. See Heated Seats on page 2 ‑ 6 for more information.
Sensing System for Passenger Airbag The passenger sensing system, if equipped, will turn off the right front passenger frontal airbag under certain conditions. The driver airbags and roof ‐ rail airbags are not affected by this. If the vehicle has a passenger sensing system, the passenger airbag status indicator will be visible on the instrument panel when the vehicle is started.
Interior Mirror V ehicles with a manual rearview mirror can be adjusted by holding the mirror in the center to move it for a clearer view behind the vehicle. T o avoid glare from the headlamps behind you, push the tab, located at the base of the mirror , toward you for daytime use and pull it for nighttime use.
Interior Lighting Dome Lamps The front and rear dome lamps turn on when any door is opened. T o turn on all dome lamps with the doors closed, turn the instrument panel brightness thumbwheel located to the right of the steering wheel and above the radio, completely to the right.
P : This position is the momentary Off/On switch for the Automatic Headlamp System. In Canada, this only works when the vehicles with an automatic transmission are in P (Park) and vehicles with a manual transmission have the parking brake set and the vehicle is not moving.
6 (Delay/Intermittent Speed Sensitive): When the lever is in the delay position, turn the band up for more frequent wipes or down for less frequent wipes. During intermittent wiping mode, the delay cycle time is sensitive to vehicle speed. As the vehicle speed increases the delay cycle time decreases and wiper movement occurs more frequently .
V ehicle Features Radio(s) Radio with CD (MP3) and USB Port shown O : Press to turn the system on and off. Turn to increase or decrease the volume. BAND: Press to choose between FM, AM, or XM ™ , if equipped. f : Select radio stations. © ¨ : Seek or scan stations.
Setting the Clock T o set the time and date for the Radio with CD (MP3) and USB port or Radio with a Single CD (MP3) player: 1. T urn the ignition key to ACC/ACCESSORY or ON/RUN. 2. Press O to turn the radio on. 3. Press H and the HR, MIN, MM, DD, YYYY (hour , minute, month, day , and year) displays.
Press the CD/AUX button to play audio from the portable player . See “ Using the Auxiliary Input Jack ” and “ Using the USB Port ” under Radio(s) on page 4 ‑ 62 . Steering Wheel Controls If equipped, some audio controls can be adjusted using the controls on the right side of the steering wheel.
Driver Information Center (DIC) The DIC display is located at the bottom of the instrument panel cluster . It shows the status of many vehicle systems and enables access to the personalization menu. The DIC buttons are located on the left side of the steering wheel.
Cruise Control The cruise control buttons are located on the left side of the steering wheel. J : On/Off. RES+: Press to resume or accelerate speed. SET − : Press to set or decrease speed. For more information, see Cruise Control on page 4 ‑ 8 . Storage Compartments V ehicles with a panel/cargo cover feature can be adjusted into four positions.
Place the panel in the upper position to conceal the cargo area. There is also a center position and a sideways position that allows access to the rear cargo area. For more information, see Rear Compartment Storage Panel/Cover on page 3 ‑ 48 . Power Outlets Accessory power outlets can be used to connect electrical equipment, such as a cellular phone.
Performance and Maintenance T raction Control System (TCS) The traction control system limits wheel spin. The system turns on automatically every time the vehicle is started. . T o turn off traction control, press and release d on the instrument panel.
Tire Pressure Monitor This vehicle may have a T ire Pressure Monitor System (TPMS). The T ire Pressure Monitor alerts you when a significant reduction in pressure occurs in one or more of the vehicle ’ s tires by illuminating the low tire pressure warning light on the instrument cluster .
Engine Oil Life System The engine oil life system calculates engine oil life based on vehicle use and displays a DIC message when it is necessary to change the engine oil and filter . The oil life system should be reset to 100% only following an oil change.
Driving for Better Fuel Economy Driving habits can affect fuel mileage. Here are some driving tips to get the best fuel economy possible. . Avoid fast starts and accelerate smoothly . . Brake gradually and avoid abrupt stops. . Avoid idling the engine for long periods of time.
OnStar ® OnStar ® uses several innovative technologies and live advisors to provide a wide range of safety , security , navigation, diagnostics, and calling services. Automatic Crash Response In a crash, built in sensors can automatically alert an OnStar advisor who is immediately connected to the vehicle to see if you need help.
The OnStar system can record and transmit vehicle information. This information is automatically sent to an OnStar call center when Q is pressed, ] is pressed, or if the airbags or ACR system deploy . This information usually includes the vehicle's GPS location and, in the event of a crash, additional information regarding the crash that the vehicle was involved in (e.
Section 2 Seats and Restraint System Head Restraints ............................... ..... 2-2 Front Seats ......................................... 2-4 Manual Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Seat Height Adjuster .
Head Restraints The front seats have adjustable head restraints in the outboard seating positions. { W ARNING: With head restraints that are not installed and adjusted properly , there is a greater chance that occupants will suffer a neck/spinal injury in a crash.
Pull the head restraint up to raise it. T o lower the head restraint, press the button, located on the top of the seatback, and push the restraint down. Push down on the head restraint after the button is released to make sure that it is locked in place.
Front Seats Manual Seats { W ARNING: Y ou can lose control of the vehicle if you try to adjust a manual driver's seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Seat Height Adjuster If your vehicle has this feature, the driver's seat height adjuster is located on the outboard side of the seat. T o raise the seat, move the lever upward repeatedly until the seat is at the desired height. T o lower the seat, move the lever downward repeatedly until the seat is at the desired height.
Power Lumbar If your vehicle has this feature, the control is located on the outboard side of the driver's seat cushion. T o increase support, press and hold the front of the control. T o decrease support, press and hold the rear of the control. Keep in mind that as your seating position changes, as it may during long trips, so should the position of your lumbar support.
Reclining Seatbacks { W ARNING: Y ou can lose control of the vehicle if you try to adjust a manual driver's seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver's seat only when the vehicle is not moving.
{ W ARNING: Sitting in a reclined position when the vehicle is in motion can be dangerous. Even when buckled up, the safety belts cannot do their job when reclined like this. The shoulder belt cannot do its job because it will not be against your body .
Passenger Folding Seatback Y our vehicle has a front passenger seat that folds flat. { W ARNING: If you fold the seatback forward to carry longer objects, such as skis, be sure any such cargo is not near an airbag. In a crash, an inflating airbag might force that object toward a person.
3. T o fold the seat flat, pull up on either lever located toward the rear of the seatback. Fold the seat forward until the seatback disengages. 4. Continue to fold the seat forward until it locks in the folded position. Pull up on the seatback to be sure it is locked.
Rear Seats Split Folding Rear Seat The seatbacks can be folded flat. T o lower the rear seatback(s): 1. Move the front seat forward and/or put the front seatback in an upright position so it does not interfere with folding the rear seatback forward. 2.
5. Pull up on the knob located on the top of the seatback on the outboard side to release the seatback. 2-12.
T o raise the rear seatback(s): { W ARNING: A safety belt that is improperly routed, not properly attached, or twisted will not provide the protection needed in a crash. The person wearing the belt could be seriously injured. After raising the rear seatback, always check to be sure that the safety belts are properly routed and attached, and are not twisted.
Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly . It also describes some things not to do with safety belts. { W ARNING: Do not let anyone ride where a safety belt cannot be worn properly .
A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive. But most crashes are in between. In many of them, people who buckle up can survive and sometimes walk away . Without safety belts, they could have been badly hurt or killed.
Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 2-16.
The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel... 2-17.
or the safety belts! With safety belts, you slow down as the vehicle does. Y ou get more time to stop. Y ou stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: Y ou could be — whether you are wearing a safety belt or not.
Q: If I am a good driver , and I never drive far from home, why should I wear safety belts? A: Y ou may be an excellent driver, but if you are in a crash — even one that is not your fault — you and your passenger(s) can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers.
Sit up straight and always keep your feet on the floor in front of you. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt.
Q: What is wrong with this? A: The shoulder belt is too loose. It will not give as much protection this way . { W ARNING: Y ou can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury .
Q: What is wrong with this? A: The lap belt is too loose. It will not give nearly as much protection this way . { W ARNING: Y ou can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Q: What is wrong with this? A: The belt is buckled in the wrong buckle. { W ARNING: Y ou can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Q: What is wrong with this? A: The belt is over an armrest. { W ARNING: Y ou can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Q: What is wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { W ARNING: Y ou can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury .
Q: What is wrong with this? A: The belt is behind the body . { W ARNING: Y ou can be seriously injured by not wearing the lap-shoulder belt properly . In a crash, you would not be restrained by the shoulder belt. Y our body could move too far forward increasing the chance of head and neck injury .
Q: What is wrong with this? A: The belt is twisted across the body . { W ARNING: Y ou can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly , or ask your dealer/retailer to fix it.
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. The following instructions explain how to wear a lap-shoulder belt properly . 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. T o see how , see “ Seats ” in the Index.
5. T o make the lap part tight, pull up on the shoulder belt. It may be necessary to pull stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants. T o unlatch the belt, push the button on the buckle. The belt should return to its stowed position.
Shoulder Belt Height Adjuster The vehicle has a shoulder belt height adjuster for the driver and right front passenger seating positions. Adjust the height so that the shoulder portion of the belt is centered on the shoulder . The belt should be away from the face and neck, but not falling off the shoulder .
Rear Safety Belt Comfort Guides This vehicle may have rear shoulder belt comfort guides for each outboard passenger position in the rear seat. If not, they are available through your dealer/retailer . The guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults.
2. Place the guide over the belt and insert the two edges of the belt into the slots of the guide. 3. Be sure that the belt is not twisted and it lies flat.
{ W ARNING: A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured. The shoulder belt should go over the shoulder and across the chest. These parts of the body are best able to take belt restraining forces.
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy .
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle's safety belts. The manufacturer's instructions that come with the booster seat state the weight and height limitations for that booster .
Q: What is the proper way to wear safety belts? A: An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should fit snugly below the hips, just touching the top of the thighs.
{ W ARNING: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly . In a crash, the child would not be restrained by the shoulder belt.
Infants and Y oung Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
{ W ARNING: Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint (Continued) W ARNING: (Continued) in a rear seat.
Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle's owner , are available in four basic types. Selection of a particular restraint should take into consideration not only the child's weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
{ W ARNING: A young child's hip bones are still so small that the vehicle's regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child's abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure.
A booster seat (C-D) is a child restraint designed to improve the fit of the vehicle's safety belt system. A booster seat can also help a child to see out the window . Securing an Add-On Child Restraint in the V ehicle { W ARNING: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle.
When securing an add-on child restraint, refer to the instructions that come with the restraint which may be on the restraint itself or in a booklet, or both, and to this manual. The child restraint instructions are important, so if they are not available, obtain a replacement copy from the manufacturer .
A label on the sun visor says, “ Never put a rear-facing child restraint in the front. ” This is because the risk to the rear-facing child is so great, if the airbag deploys. { W ARNING: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates.
Lower Anchors and T ethers for Children (LA TCH) The LA TCH system holds a child restraint during driving or in a crash. This system is designed to make installation of a child restraint easier . The LA TCH system uses anchors in the vehicle and attachments on the child restraint that are made for use with the LA TCH system.
T op T ether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (B) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash.
Lower Anchor and T op T ether Anchor Locations Rear Seat j (Lower Anchor): Seating positions with two lower anchors. i (T op T ether Anchor): Seating positions with top tether anchors. Front Passenger Seat — Panel and Rear Seat Delete Models i (T op T ether Anchor): Seating position with a top tether anchor .
T o assist you in locating the top tether anchors, this symbol is located next to each top tether anchor . On vehicles equipped with rear seats, the top tether anchor symbols for the rear outboard positions are on the lower side of the quarter panels.
When the top tether anchor is being used for a child restraint, do not use the same anchor to secure cargo. V ehicles without Rear Seats — Panel and Rear Seat Delete Models If the vehicle does not have a rear seat, there is an exposed top tether anchor for the front passenger position located on the rear passenger side cargo floor, behind the second row door .
Securing a Child Restraint Designed for the LA TCH System { W ARNING: If a LA TCH-type child restraint is not attached to anchors, the child restraint will not be able to protect the child correctly . In a crash, the child could be seriously injured or killed.
Notice: Do not let the LA TCH attachments rub against the vehicle ’ s safety belts. This may damage these parts. If necessary , move buckled safety belts to avoid rubbing the LA TCH attachments. Do not fold the empty rear seat with a safety belt buckled.
2. 3. T o secure a child restraint in the front passenger position, only if your vehicle does not have rear seats, find the top tether anchor located on the passenger side cargo floor behind the second row door . Be sure to use an anchor located on the same side of the vehicle as the seating position where the child restraint will be placed.
If the position you are using has an adjustable headrest or head restraint and you are using a single tether , raise the headrest or head restraint and route the tether under the headrest or head restraint and in between the headrest or head restraint posts.
If more than one child restraint needs to be installed in the rear seat, be sure to read Where to Put the Restraint on page 2 ‑ 43 . 1. Put the child restraint on the seat. 2. Pick up the latch plate, and run the lap and shoulder portions of the vehicle's safety belt through or around the restraint.
5. T o tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor . When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt.
Securing a Child Restraint in the Right Front Seat Position This vehicle has airbags. A rear seat is a safer place to secure a forward-facing child restraint. See Where to Put the Restraint on page 2 ‑ 43 . In addition, the vehicle may have a passenger sensing system which is designed to turn off the right front passenger frontal airbag under certain conditions.
If the vehicle does not have a rear seat that will accomodate a rear ‐ facing child restraint, a rear-facing child restraint should not be installed in the vehicle, even if the airbag is off. If your child restraint has the LA TCH system, see Lower Anchors and T ethers for Children (LA TCH) on page 2 ‑ 45 for how and where to install the child restraint using LA TCH.
4. Push the latch plate into the buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary . 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock.
6. T o tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor . When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt.
Airbag System The vehicle has the following airbags: . A frontal airbag for the driver . . A frontal airbag for the right front passenger . The vehicle may have the following airbags: . A roof-rail airbag for the driver and the passenger seated directly behind the driver .
Here are the most important things to know about the airbag system: { W ARNING: Y ou can be severely injured or killed in a crash if you are not wearing your safety belt — even if you have airbags. Airbags are designed to work with safety belts, but do not replace them.
{ W ARNING: Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Airbags plus lap-shoulder belts offer protection for adults and older children, but not for young children and infants. Neither the vehicle's safety belt system nor its airbag system is designed for them.
Where Are the Airbags? The driver's frontal airbag is in the middle of the steering wheel. The right front passenger's airbag is in the instrument panel on the passenger's side.
Driver Side shown, Passenger Side similar If your vehicle has roof-rail airbags for the driver , right front passenger , and second row outboard passengers, they are in the ceiling above the side windows. { W ARNING: If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death.
When Should an Airbag Inflate? Frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver's or right front passenger's head and chest. However , they are only designed to inflate if the impact exceeds a predetermined deployment threshold.
In addition, your vehicle has dual-stage frontal airbags. Dual-stage airbags adjust the restraint according to crash severity . Y our vehicle has an electronic frontal sensor , which helps the sensing system distinguish between a moderate frontal impact and a more severe frontal impact.
What Makes an Airbag Inflate? In a deployment event, the sensing system sends an electrical signal triggering a release of gas from the inflator . Gas from the inflator fills the airbag causing the bag to break out of the cover and deploy . The inflator , the airbag, and related hardware are all part of the airbag module.
What Will Y ou See After an Airbag Inflates? After the frontal airbags inflate, they quickly deflate, so quickly that some people may not even realize an airbag inflated. Roof-rail airbags may still be at least partially inflated for some time after they deploy .
{ W ARNING: A crash severe enough to inflate the airbags may have also damaged important functions in the vehicle, such as the fuel system, brake and steering systems, etc. Even if the vehicle appears to be drivable after a moderate crash, there may be concealed damage that could make it difficult to safely operate the vehicle.
Passenger Sensing System If the vehicle has one of the passenger airbag status indicators pictured in the following illustrations, then the vehicle has a passenger sensing system for the right front passenger position. The passenger airbag status indicator , if equipped, is visible on the instrument panel when the vehicle is started.
{ W ARNING: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates. This is because the back of the rear-facing child restraint would be very close to the inflating airbag. A child in a forward-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates and the passenger seat is in a forward position.
The passenger sensing system is designed turn on (may inflate) the right front passenger frontal airbag anytime the system senses that a person of adult size is sitting properly in the right front passenger seat. When the passenger sensing system has allowed the airbag to be enabled, the on indicator will light and stay lit to remind you that the airbag is active.
If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. T urn the vehicle off. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers.
If the Off Indicator is Lit for an Adult-Size Occupant If a person of adult-size is sitting in the right front passenger seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat. If this happens, use the following steps to allow the system to detect that person and enable the right front passenger frontal airbag: 1.
Additional Factors Affecting System Operation Safety belts help keep the passenger in position on the seat during vehicle maneuvers and braking, which helps the passenger sensing system maintain the passenger airbag status. See “ Safety Belts ” and “ Child Restraints ” in the Index for additional information about the importance of proper restraint use.
If the passenger seat gets wet, dry the seat immediately . If the airbag readiness light is lit, do not install a child restraint or allow anyone to occupy the seat. See Airbag Readiness Light on page 4 ‑ 27 for important safety information. The on indicator may be lit if an object, such as a briefcase, handbag, grocery bag, laptop or other electronic device, is put on an unoccupied seat.
Adding Equipment to Y our Airbag-Equipped V ehicle Q: Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? A: Y es. If you add things that change the vehicle's frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly .
Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check that the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly . Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job.
Replacing Restraint System Parts After a Crash { W ARNING: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. T o help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
2 NOTES 2-80.
Section 3 Features and Controls Keys ........................... ..................... 3-3 Remote Keyless Entry (RKE) System . . . . . . . . . . . 3-4 Remote Keyless Entry (RKE) System O p e r a t i o n ................... ............... ... 3 - 4 Remote Vehicle Start .
Section 3 Features and Controls Object Detection Systems .. ..................... 3-44 Rear Vision Camera (RVC) . . . . . . . . . . . . . . . . . . . . 3-44 Storage Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-47 G l o v e B o x .
Keys { W ARNING: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window .
The key has a bar-coded key tag that the dealer/retailer or qualified locksmith can use to make new keys. Store this information in a safe place, not in your vehicle. Notice: If you ever lock your keys in the vehicle, you may have to damage the vehicle to get in.
With Remote Start and Remote Rear Doors Shown, Without Similar / (Remote V ehicle Start): For vehicles with this feature, press to start the engine from outside the vehicle using the RKE transmitter . See Remote V ehicle Start on page 3 ‑ 7 for additional information.
Remote Rear Door Operation (Panel) * : Press and hold for about one second to open the rear driver side door . + : Press and hold for about one second to open the rear passenger side door . Programming T ransmitters to the V ehicle Only RKE transmitters programmed to the vehicle will work.
Remote V ehicle Start Y our vehicle may have a remote start feature. This feature allows you to start the engine from outside the vehicle. It may also start the vehicle's heating or air conditioning systems. See Climate Control System on page 4 ‑ 18 for additional information.
If the remote start procedure is used again before the first 10 minute time frame has ended, the first 10 minutes will immediately expire and the second 10 minute time frame will start. After your vehicle's engine has been started two times using the remote start button, the vehicle's ignition switch must be turned to ON/RUN and then back to LOCK/OFF using the key before the remote start procedure can be used again.
Doors and Locks Door Locks { W ARNING: Unlocked doors can be dangerous. . Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked.
Power Door Locks Driver's side shown, Passenger's side similar The power door lock switches are located on the driver's and front passenger's door next to the door handle. Press the top of the switch to unlock the doors. Press the bottom of the switch to lock the doors.
Automatic Door Lock On vehicles with power door locks, the doors automatically lock when the shift lever is moved out of (P) Park for a vehicle with an automatic transmission. For a vehicle with a manual transmission, the speed must be greater than 5 mph (8 km/h).
T o open a rear door while the security lock is on, do the following: 1. Unlock the door using the remote keyless entry transmitter , the power door lock switch, or by lifting the rear door manual lock. 2. Open the door from the outside. T o cancel the rear door security lock, do the following: 1.
Liftgate T o lock the liftgate from the outside, press the lock button on the Remote Keyless Entry (RKE) transmitter . T o unlock the liftgate with the RKE, press the unlock button twice within five seconds. For more information, see Remote Keyless Entry (RKE) System Operation on page 3 ‑ 4 .
Manual Liftgate Release T o manually open the liftgate, do the following: 1. Remove the trim plug, located on the inside of the liftgate near the center . 2. Locate the release lever on the latch. The lever is located about three inches (7.62 cm) behind the trim in the access hole.
3. Insert a tool into the access hole. Push the release lever rearward. 4. The liftgate will unlatch when the lever is pushed rearward. Push the liftgate to open.
Windows { W ARNING: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Power Windows { W ARNING: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function and they could be seriously injured or killed if caught in the path of a closing window .
Express-Down Window The driver's window switch has an express-down feature that allows the window to be lowered without holding the switch. Press the switch part way , and the driver's window will open a small amount. Press the switch down all the way , release it, and the window will go down automatically .
Content Theft-Deterrent Y our vehicle may have a content theft-deterrent alarm system. Arming the System T o arm the system: 1. T urn the ignition off. 2. Press lock on the RKE transmitter . The system will arm after either of the following occur: . 30 seconds after all the doors are closed.
How to T urn Off the System Alarm T o turn off the system alarm, do one of the following: . Press the lock button on the RKE transmitter . The system will then re-arm itself. . Press the unlock button on the RKE transmitter . This will also disarm the system.
If the engine still does not start, and the key appears to be undamaged, try another ignition key . At this time, you may also want to check the fuse, see Fuses and Circuit Breakers on page 6 ‑ 1 19 . If the engine still does not start with the other key , your vehicle needs service.
Starting and Operating Y our V ehicle New V ehicle Break-In Notice: The vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines: . Do not drive at any one constant speed, fast or slow , for the first 500 miles (805 km).
Ignition Positions The ignition switch has four different positions. In order to shift out of P (Park), the ignition must be in ON/RUN or ACC/ACCESSORY and the brake pedal must be applied. Notice: Using a tool to force the key to turn in the ignition could cause damage to the switch or break the key .
R (ON/RUN): This is the position in which you can operate the electrical accessories and to display some instrument panel cluster warning and indicator lights. The switch stays in this position when the engine is running. If you leave the key in the ACC/ACCESSORY or ON/RUN position with the engine off, the battery could be drained.
3. Locate the plunger . 4. Press and hold the plunger while turning the ignition key to LOCK/OFF . Remove the key . Have the vehicle serviced at your dealer/retailer as soon as possible. Retained Accessory Power (RAP) These vehicle accessories may be used for up to 10 minutes after the engine is turned off.
Manual T ransmission The shift lever should be in N (Neutral) and the parking brake engaged. Hold the clutch pedal down to the floor and start the engine. The vehicle will not start if the clutch pedal is not all the way down. Starting Procedure 1. With your foot off the accelerator pedal, turn the ignition key to ST ART .
Engine Coolant Heater The engine coolant heater can provide easier starting and better fuel economy during engine warm ‐ up in cold weather condition at or below 0°F ( − 18°C). V ehicles with am engine coolant heater should be plugged in at least four hours before starting.
Automatic T ransmission Operation If the vehicle has an automatic transmission, the shift lever is located on the console between the seats. There are several different positions for the automatic transmission. P (Park): This position locks the front wheels.
Make sure the shift lever is fully in P (Park) before starting the engine. The vehicle has an automatic transmission shift lock control system. Y ou have to fully apply the regular brakes first and then press the shift lever button before the vehicle can shift from P (Park) when the ignition key is in ON/RUN.
D (Drive): This position is for normal driving with the automatic transmission. It provides the best fuel economy . If you need more power for passing and you are: . Going less than about 35 mph (55 km/h), push the accelerator pedal about halfway down.
Manual T ransmission Operation This is the shift pattern for standard models. This is the shift pattern for SS models. Here is how to operate the manual transmission: Notice: Do not rest your hand on the shift lever while driving. The pressure could cause premature wear in the transmission.
2 (Second): Press the clutch pedal as you let up on the accelerator pedal and shift into 2 (Second). Then, slowly let up on the clutch pedal as you press the accelerator pedal. 3 (Third), 4 (Fourth) and 5 (Fifth): Shift into 3 (Third), 4 (Fourth) and 5 (Fifth) the same way you do for 2 (Second).
Up-Shift Light If the vehicle has a manual transmission, there may be an up-shift light. This light will show you when to shift to the next higher gear for the best fuel economy . When this light comes on, you can shift to the next higher gear if weather , road, and traffic conditions let you.
T o utilize this feature: 1. Accelerate the vehicle by fully depressing the accelerator pedal. 2. Just prior to reaching the maximum engine speed, quickly complete the upshift utilizing the clutch while keeping the accelerator pedal fully applied. A quicker shift maneuver gives the best performance.
{ W ARNING: If the front passenger seat back is folded down, the armrest may make it awkward to grab and pull up the parking brake lever . If the lever is not pulled up far enough, the vehicle may roll and you or others could be injured. Move your hand lower on the lever or raise the seat back so that you can set the brake.
Shifting Into Park (Automatic T ransmission) { W ARNING: It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly .
T orque Lock (Automatic T ransmission) If you are parking on a hill and you do not shift into P (Park) properly , the weight of the vehicle may put too much force on the parking pawl in the transmission. Y ou may find it difficult to pull the shift lever out of P (Park).
If the vehicle has an uncharged battery or a battery with low voltage, try charging or jump starting the battery . See Jump Starting on page 6 ‑ 41 for more information. T o shift out of P (Park): 1. Apply the brake pedal. 2. Then press the shift lever button.
Engine Exhaust { W ARNING: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if: . The vehicle idles in areas with poor ventilation (parking garages, tunnels, deep snow that may block underbody airflow or tail pipes).
Running the V ehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know . { W ARNING: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Mirrors Manual Rearview Mirror Hold the inside rearview mirror in the center to move it for a clearer view behind your vehicle. Adjust the mirror to avoid glare from the headlamps behind you. Push the tab forward for daytime use and pull it for nighttime use.
Compass Calibration If after a few seconds the display does not show a compass direction, (N for North for example), there may be a strong magnetic field interfering with the compass. Interference can be caused by a magnetic antenna mount, note pad holder , or similar object.
Outside Power Mirrors Controls for the outside power mirrors are located on the driver door armrest. 1. Press the left or right side of the selector switch located beneath the control pad, to select the driver or passenger mirror . 2. Press one of the four buttons located on the control pad to move the mirror to the desired direction.
Object Detection Systems Rear Vision Camera (RVC) The vehicle may have a Rear Vision Camera system. Read this entire section before using it. { W ARNING: The Rear Vision Camera (RVC) system does not replace driver vision. RVC does not: . Detect objects that are outside the camera's field of view , below the bumper , or underneath the vehicle.
T urning the Rear Vision Camera System Off or On T o turn off the rear vision camera system, press and hold z , located on the inside rearview mirror , until the left indicator light turns off. The rear vision camera display is now disabled. T o turn the rear vision camera system on again, press and hold z until the left indicator light illuminates.
A. View displayed by the camera. B. Corner of the rear bumper . When the System Does Not Seem T o Work Properly The rear vision camera system might not work properly or display a clear image if: . The RVC is turned off. See “ Turning the Rear Camera System On or Off ” earlier in this section.
The rear vision camera system display in the rearview mirror may turn off or not appear as expected due to one of the following conditions. If this occurs the left indicator light on the mirror will flash. . A slow flash may indicate a loss of video signal, or no video signal present during the reverse cycle.
Rear Storage Area The vehicle could also have two rear storage areas that can be used for small items. Rear Compartment Storage Panel/Cover The vehicle could have an adjustable panel/cargo cover feature. The panel/cargo cover can be adjusted into four positions.
T o use the panel in the lowest position: The panel can be used in this position if additional space above the panel is needed. Cargo can be placed on top of the panel in this position. 1. Insert the front corners of the panel into the lower guides. 2.
The center position is with the front corners placed in the lower guides and the rear corners placed in the upper guides. Do not load cargo on the panel in this position. The last position is with the front corners in the lower guides, panel sideways, closest to the rear seat for subfloor access.
For vehicles with a roof rack, the rack can be used to load items. For roof racks that do not have crossrails included, GM Certified crossrails can be purchased as an accessory . See your dealer/retailer for additional information. Notice: Loading cargo on the roof rack that weighs more than 75 kg (165 lbs) or hangs over the rear or sides of the vehicle may damage the vehicle.
There is a rod that hooks into place to prop open the lid. Push the rod towards the lid to unhook it and lower the lid. Sunroof The vehicle may have a power sunroof. The switches that operate the sunroof are located in the headliner . T o open or close the sunroof, the ignition must be in ON/RUN, ACC/ACCESSORY , or Retained Accessory Power (RAP) must be active.
Express Open: T o express open the power sunroof, fully press the driver's side switch rearward once. T o stop the sunroof glass in a desired position other than to the express-open position, press the switch again, in either direction, to stop the movement.
2 NOTES 3-54.
Section 4 Instrument Panel Instrument Panel Overview ........ ........... ..... 4-3 Hazard W arning Flashers . . . . . . . . . . . . . . . . . . . . . . . 4-3 Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Section 4 Instrument Panel F o g L a m p L i g h t ................................ 4 - 3 9 Highbeam On Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39 F u e l G a u g e .................................... 4 - 4 0 Boost Gauge . . .
Instrument Panel Overview Hazard W arning Flashers | (Hazard W arning Flasher): Press this button located on the instrument panel, to make the front and rear turn signal lamps flash on and off. This warns others that you are having trouble. Press | again to turn the flashers off.
T urn Signal/Multifunction Lever The lever on the left side of the steering column operates the following: G : T urn and Lane-Change Signals 5 3 : Headlamp High/Low-Beam Changer O : Exterior Lamp Control Flash-to-Pass. Information for these features is on the pages following.
Headlamp High/Low-Beam Changer T o change the headlamps from low beam to high beam, push the turn signal lever away from you. This indicator light appears on the instrument panel cluster when the high beams are on. T o change the headlamps from high beam to low beam, pull the turn signal lever toward you.
6 (Delay/Intermittent Speed Sensitive): When the lever is in the delay position, turn the band up for more frequent wipes or down for less frequent wipes. During intermittent wiping mode, the delay cycle time is sensitive to vehicle speed. As the vehicle speed increases the delay cycle time decreases and wiper movement occurs more frequently .
Rear Window Wiper/W asher The rear window washer/wiper button is located on the instrument panel below the climate controls. { W ARNING: In freezing weather , do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision.
Cruise Control With cruise control, a speed of about 40 km (25 mph) or more can be maintained without keeping your foot on the accelerator . Cruise control does not work at speeds below 40 km (25 mph). The brake must be applied at least one time, after the vehicle has been started, before cruise control will function.
J (On/Off): Press to turn the cruise control system on and off. The indicator light on the button comes on when the cruise control is on and goes off when the cruise control is turned off. RES+ (Resume): Press to resume a set speed and to accelerate the speed.
Increasing Speed While Using Cruise Control There are two ways to go to a higher speed. 1. Disengage the cruise control by applying the brake pedal, but do not turn it off. Accelerate to a higher speed and reset the cruise control. 2. If the cruise control system is already engaged, press the RES+ button.
Erasing Speed Memory The cruise control set speed memory is erased when the cruise control or the ignition is turned off. Headlamps The lever on the left side of the steering column operates the exterior lamps. The exterior lamp switch has the following four positions: 2 (Headlamps): T urns on the headlamps, parking lamps, and taillamps.
When the ignition is turned of f, the wiper-activated headlamps will immediately turn off. They also turn off 15 seconds after the windshield wiper control is turned off. Headlamps on Reminder If the drivers door is opened with the ignition off and the lamps on, a warning chime will sound.
There is a delay in the transition between the daytime and nighttime operation of the automatic lamp control system so that driving under bridges or bright overhead street lights does not affect the system. The automatic lamp control system will only be affected when the light sensor sees a change in lighting lasting longer than this delay .
Instrument Panel Brightness The control for this feature is located to the right of the steering wheel and above the radio. Move the thumbwheel to the left to dim the lights or to the right to brighten the lights. The dome lamps will turn on when the thumbwheel is moved completely to the right.
Electric Power Management This vehicle has Electric Power Management (EPM), an advanced control system. It estimates the battery's temperature and state of charge and then adjusts the voltage for best performance and extended life of the battery .
Accessory Power Outlet(s) Accessory power outlets can be used to connect electrical equipment, such as a cellular phone. The accessory power outlets are located on the instrument panel below the climate controls and at the rear of the center console. There may be an outlet in the rear cargo area on the passenger side.
Rear Power Plug for Converters The vehicle may have a power plug connector located in the rear cargo area on the passenger side behind the service panel. The power connector wiring can be accessed by removing the service panel to begin installation. This plug can be used to supply power to commercial converters and contains four different circuits.
Ashtray(s) and Cigarette Lighter The vehicle may have an ashtray and cigarette lighter . T o use the lighter , located on the instrument panel below the climate controls, push it in all the way and let go. When it is ready , it will pop back out by itself.
9 (Off): Turn the fan control to this position to turn the fan off. T emperature Control: T urn clockwise or counterclockwise to increase or decrease the temperature. 9 (Fan): T urn clockwise or counterclockwise to increase or decrease the fan speed. In any setting other than off, the fan runs continuously while the ignition is in ON/RUN.
For quick cool down on hot days: 1. Select H . 2. Select @ . 3. Select # . 4. Select the coolest temperature. 5. Select the highest fan speed. Using these settings together for long periods of time can cause the air inside of the vehicle to become too dry .
The rear window defogger turns off approximately 15 minutes after the button is pressed. If turned on again, the defogger only runs for approximately seven minutes before turning off. If the vehicle speed is greater than 80 km/h (50 mph) and the rear defogger is on, it remains on as long as the speed is greater than 80 km/h (50 mph).
T o access the passenger compartment air filter: 1. Open and empty the glove box. 2. Press both glove box stops outward to let the glove box drop open completely . 3. Pull the three tabs of the filter access door down and open the access door downward.
4. Pull the filter out, keeping it upwards. Install the new air filter with the AIR FLOW arrow pointing downward. Reverse Steps 1 through 4 to reassemble. W arning Lights, Gauges, and Indicators W arning lights and gauges can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Instrument Panel Cluster United States Manual T ransmission Cluster shown, Automatic, SS and Canada similar 4-24.
Speedometer and Odometer The speedometer shows the speed in both kilometers per hour (km/h) and miles per hour (mph). The vehicle's odometer works together with the Driver Information Center (DIC). T rip A and Trip B can be set on the odometer . See “ T rip Information ” under DIC Operation and Displays on page 4 ‑ 46 .
Safety Belt Reminders Driver Safety Belt Reminder Light When the engine is started, a chime sounds for several seconds to remind a driver to fasten the safety belt, unless the driver safety belt is already buckled. The safety belt light comes on and stays on for several seconds, then flashes for several more.
Airbag Readiness Light The system checks the airbag's electrical system for possible malfunctions. If the light stays on it indicates there is an electrical problem. The system check includes the airbag sensor , the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module.
Passenger Airbag Status Indicator If the vehicle has one of the passenger airbag status indicators pictured in the following illustrations, then the vehicle has a passenger sensing system for the right front passenger position. The passenger airbag status indicator , if equipped, is on the instrument panel.
Charging System Light This light comes on briefly when the ignition key is turned on, but the engine is not running, as a check to show it is working. It should go out once the engine is running. If it stays on, or comes on while driving, there could be a problem with the charging system or it could indicate that there are problems with a generator drive belt, or that there is an electrical problem.
Brake System W arning Light The vehicle's hydraulic brake system is divided into two parts. If one part is not working, the other part can still work and stop the vehicle. For good braking both parts need to be working well. If the warning light comes on, there is a brake problem.
Antilock Brake System (ABS) W arning Light For vehicles with the Antilock Brake System (ABS), this light comes on briefly when the engine is started. If it does not, have the vehicle serviced by your dealer/retailer . If the system is working normally the indicator light then goes off.
Enhanced T raction System (ETS) Indicator/W arning Light For vehicles with the Enhanced Traction System (ETS), this light serves as an indicator and warning light. This light comes on briefly while the engine is started. If it does not, have the vehicle serviced by your dealer/ retailer .
Electronic Stability Control (ESC)/ T raction Control System (TCS) Indicator/W arning Light The Electronic Stability Control (ESC) system or the T raction Control System (TCS) indicator/warning light comes on briefly when the engine is started. If it does not, have the vehicle serviced by the dealer/ retailer .
Engine Coolant T emperature W arning Light This light comes on briefly while starting the vehicle. If it does not, have the vehicle serviced by the dealer/ retailer . If the system is working normally the indicator light goes off. Notice: Driving with the engine coolant temperature warning light on could cause the vehicle to overheat.
Tire Pressure Light For vehicles with a tire pressure monitoring system, this light comes on briefly when the engine is started. It provides information about tire pressures and the Tire Pressure Monitoring System. When the Light is On Steady This indicates that one or more of the tires is significantly underinflated.
If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent. Being aware of the light can prevent more serious damage to the vehicle.
Light On Steady: An emission control system malfunction has been detected on the vehicle. Diagnosis and service might be required. An emission system malfunction might be corrected by doing the following: . Make sure the fuel cap is fully installed. See Filling the T ank on page 6 ‑ 10 .
Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle. Failure to pass this inspection could prevent getting a vehicle registration.
Notice: Lack of proper engine oil maintenance can damage the engine. The repairs would not be covered by the vehicle warranty . Always follow the maintenance schedule in this manual for changing engine oil. This light comes on briefly while starting the engine.
Fuel Gauge The fuel gauge indicates about how much fuel is left in the fuel tank. An arrow on the fuel gauge indicates the side of the vehicle the fuel door is on. Here are four things that some owners ask about. None of these show a problem with the fuel gauge: .
This gauge displays the air pressure level in the intake manifold before it enters the engine's combustion chamber . It is automatically centered at zero every time the engine is started. Actual vacuum or boost is displayed from this zero point. Changes in ambient pressure, such as driving in mountains and changing weather , will slightly change the zero reading.
Region A Gauge and Speedometer Displays Change the information displayed in Region A by turning the knob either clockwise or counterclockwise. The available gauges are: BOOST : Displays positive boost pressure as determined by the manifold air pressure (MAP) sensor .
Readouts #2 TIRE PRESSURES: Displays the last gauge tire pressures recorded from each of the wheel mounted tire pressure sensors. Readouts #3 BAROMETER: Displays ambient air pressure as measured by the engine ’ s ambient pressure sensor . OUTSIDE TEMPERA TURE: Displays ambient temperature as measured by an outside air temperature sensor .
This indicator comes on when Competitive Driving Mode (A) has been set using the traction control switch. This telltale comes on whenever conditions are right for the Launch Mode (B) to activate. See Electronic Stability Control (ESC) on page 5 ‑ 6 for more information on Competitive Driving Mode and Launch Control.
SETUP MENU Options GAUGE APPEARANCE: While the gauge is highlighted, press the RPD knob. Then turn the knob to choose the background color for a gauge. Press the knob again when gauge color is chosen. SHIFT LIGHT SETUP: This screen establishes a RPM range where the shift light comes on for each gear .
Driver Information Center (DIC) Y our vehicle has a Driver Information Center (DIC). The DIC display gives you the status of many of your vehicle's systems. The DIC is also used to display driver personalization menu modes and warning/status messages.
TRIP A or TRIP B Press the information button until TRIP A or TRIP B display . These modes show the current distance traveled since the last reset for each trip odometer in either miles (mi) or kilometers (km). Both odometers can be used at the same time.
A V (Average) SPEED Press the information button until A V SPEED displays. This mode shows the vehicle's average speed in miles per hour (mph) or kilometers per hour (km/h). T o reset the average vehicle speed, press and hold the reset button while A V SPEED is displayed.
AUTO (Automatic) LIGHTS OFF This message displays if the automatic headlamp system is disabled with the headlamp switch. See Automatic Headlamp System on page 4 ‑ 12 for more information. AUTO (Automatic) LIGHTS ON This message displays if the automatic headlamp system is enabled with the headlamp switch.
CRUISE ENGAGED This message displays when the cruise control system is active. See Cruise Control on page 4 ‑ 8 for more information. DOOR AJAR This message displays if one or more of the vehicle's doors are open. Make sure that the door(s) are closed completely .
ESC (Electronic Stability Control) OFF If your vehicle has Electronic Stability Control (ESC), this message displays and the ESC/TCS light on the instrument panel cluster comes on solid when ESC is turned off. Adjust your driving accordingly . See Electronic Stability Control (ESC) on page 5 ‑ 6 and Electronic Stability Control (ESC)/T raction Control System (TCS) Indicator/Warning Light on page 4 ‑ 33 for more information.
LOW TRACTION If your vehicle has the Enhanced T raction System (ETS) or Traction Control System (TCS), this message displays and the ETS light or the ESC/TCS light on the instrument panel cluster flashes when the system is actively limiting wheel spin.
SERVICE TRACTION If your vehicle has the Enhanced T raction System (ETS) or Traction Control System (TCS), this message displays and a chime sounds when the system is not functioning properly . The ETS light or the ESC/TCS light also appears on the instrument panel cluster .
TRACTION OFF If your vehicle has the Enhanced T raction System (ETS) or Traction Control System (TCS), this message displays and the ETS light or the ESC/TCS light on the instrument panel cluster comes on solid when the system is turned off. Adjust your driving accordingly .
Personalization Menu Modes OIL LIFE RESET When this feature is displayed, you can reset the engine oil life system. T o reset the system, see Engine Oil Life System on page 6 ‑ 23 . See “ OIL LIFE ” under DIC Operation and Displays on page 4 ‑ 46 for more information.
LOCK HORN This feature, which allows the vehicle's horn to chirp every time the lock button on the Remote Keyless Entry (RKE) transmitter is pressed, can be enabled or disabled. When LOCK HORN appears on the display , press and hold the reset button for at least one second to scroll through the available settings: OFF (default): The horn will not chirp on the first press of the lock button on the RKE transmitter .
LIGHT FLASH This feature, which allows the vehicle's exterior hazard/ turn signal lighting to flash every time the lock or unlock button on the Remote Keyless Entry (RKE) transmitter is pressed, can be enabled or disabled. When LIGHT FLASH appears on the display , press and hold the reset button for at least one second to scroll through the available settings: OFF: The exterior hazard/turn signal lighting will not flash when the lock or unlock button on the RKE transmitter is pressed.
AUTO UNLK (Unlock) This feature, which allows the vehicle to automatically unlock certain doors, can be enabled or disabled. When AUTO UNLK appears on the display , press and hold the reset button for at least one second to scroll through the available settings: ALL (default): All of the doors will automatically unlock.
EXT (Exterior) LIGHTS This feature, which allows the vehicle's exterior perimeter lighting to turn on each time the unlock button on the Remote Keyless Entry (RKE) transmitter is pressed, can be enabled or disabled. When EXT LIGHTS appears on the display , press and hold the reset button for at least one second to scroll through the available settings: OFF: The exterior perimeter lighting will not turn on when the unlock button on the RKE transmitter is pressed.
Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. { W ARNING: T aking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others.
Setting the Clock Without Date Display AM/FM Base Radio with a Single CD Player T o set the time: 1. T urn the ignition key to ACC/ACCESSORY or ON/RUN. Press O to turn the radio on. 2. Press H until the hour begins flashing on the display . Press H a second time and the minute begins flashing on the display .
The date does not automatically display . T o see the date press H while the radio is on. The date with display times out after a few seconds and goes back to the normal radio and time display . T o change the time default setting from 12 hour to 24 hour or to change the date default setting from month/day/year to day/month/year: 1.
Radio with CD (MP3) and USB Port shown, Radio with CD (MP3) similar The vehicle has one of these radios as its audio system. Radio Data System (RDS) The radio may have RDS. The RDS feature is available for use only on FM stations that broadcast RDS information.
Playing the Radio O (Power/V olume): Press to turn the system on and off. T urn to increase or decrease the volume. Speed Compensated V olume (SCV): Radios with the Speed Compensated V olume (SCV) feature automatically adjust the radio volume to compensate for road and wind noise as the vehicle speeds up or slows down, so that the volume level is consistent.
¨ SEEK: Press to seek or scan stations with a strong signal in the selected band. . T o seek stations, press and release ¨ SEEK to go to the next station and stay there. . T o scan stations, press and hold ¨ SEEK for a few seconds until the radio beeps once.
F A V (Favorites): A maximum of 36 stations can be stored as favorites using the six softkeys located below the radio station frequency tabs and by using the radio favorites page button (F A V button). Press FA V to go through up to six pages of favorites, each having six favorite stations available per page.
Storing a Radio Station as a Preset Radios that have numbered pushbuttons store radio stations as presets. Up to 18 stations (six FM1, six FM2, and six AM), can be programmed on the six numbered buttons. T o store preset stations: 1. T une in the desired station.
The radio may also be capable of adjusting all tone and speaker controls to the middle position by pressing f for more than two seconds until the radio beeps once. If a station's frequency is weak, or has static, decrease the treble. EQ (Equalization): Press this button to select preset equalization settings.
Finding a Category (CA T) Station (XM Satellite Radio Service Only) CA T (Category): The radio may have the CA T button feature. T o select and find a desired category: 1. Press BAND until the XM frequency displays. 2. Press CA T to display the category tabs on the radio display .
Radio Messages Calibration Error: Displays if the radio is no longer calibrated properly for the vehicle. The vehicle must be returned to your dealer/retailer for service. Loc or Locked: Displays when the THEFTLOCK ® system has activated. T ake the vehicle to your dealer/ retailer for service.
¨ SEEK: Press to go to the next track. Press and hold or press multiple times to continue moving forward through the tracks on the CD. s REV (Reverse): Press and hold to reverse playback quickly within a track. Sound is heard at a reduced volume and the elapsed time of the track displays.
CD Messages CHECK DISC: If an error message displays and/or the CD comes out, it could be for one of the following reasons: . The CD player is very hot. When the temperature returns to normal, the CD should play . . The road is very rough. When the road becomes smoother , the CD should play .
Notice: If a label is added to a CD, or more than one CD is inserted into the slot at a time, or an attempt is made to play scratched or damaged CDs, the CD player could be damaged. While using the CD player , use only CDs in good condition without any label, load one CD at a time, and keep the CD player and the loading slot free of foreign materials, liquids, and debris.
Using the USB Port Radio's with a USB port can control a USB storage device or an iPod ® using the radio buttons and knobs. See Using an MP3 on page 4 ‑ 74 for information about how to connect and control a USB storage device or an iPod. USB Support The USB connector is located on the front of the radio and uses the USB 2.
USB Supported File and Folder Structure The radio supports: . Up to 700 folders. . Up to 8 folders in depth. . Up to 65,535 files. . Folder and file names up to 64 bytes. . Files with an .mp3 or .wma file extension. . AAC files stored on an iPod. . F A T16 .
Preprogrammed Playlists CDs that have preprogrammed playlists that were created using WinAmp ™ , MusicMatch ™ , or Real Jukebox ™ software can be accessed, however , there is no playlist editing capability using the radio. These playlists are treated as special folders containing compressed audio song files.
When the scan is finished, the disc begins playing files in order by artist. The current artist playing is shown on the second line of the display . Once all songs by that artist are played, the player moves to the next artist in alphabetical order and begins playing files by that artist.
Using the Radio to Control a USB Storage Device or iPod The radio can control a USB storage device or an iPod using the radio buttons and knobs and display song information on the radio ’ s display . f (T une): T urn to select files. © SEEK: Press to go to the start of the track, if more than ten seconds have played.
3. Press f to select the desired folder. If there is more then one folder , repeat Steps 1 and 2 until the desired folder is reached. 4. T urn f to scroll through the files in the selected folder . 5. Press f to select the desired file to be played. T o skip through large lists, the five softkeys can be used to navigate in the following order: .
Repeat Functionality T o use Repeat: Press the softkey below " or ' to select between Repeat All and Repeat T rack. " (Repeat All): Press the softkey below " to repeat all tracks. The tab appears lowered when Repeat All is being used.
Loading XM: The audio system is acquiring and processing audio and text data. No action is needed. This message should disappear shortly . Channel Off Air: This channel is not currently in service. Tune in to another channel. Channel Unauth: This channel is blocked or cannot be received with your XM Subscription package.
Bluetooth ® V ehicles with a Bluetooth system can use a Bluetooth capable cell phone with a Hands Free Profile to make and receive phone calls. The system can be used while the key is in ON/RUN or ACC/ACCESSORY position. The range of the Bluetooth system can be up to 9.
Pairing A Bluetooth enabled cell phone must be paired to the in ‐ vehicle Bluetooth system first and then connected to the vehicle before it can be used. See the cell phone manufacturers user guide for Bluetooth functions before pairing the cell phone.
Listing All Paired and Connected Phones 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Bluetooth ” . The system responds with “ Bluetooth ready ” followed by a tone. 3. Say “ List ” .
Using the Store Command The store command allows a phone number to be stored without entering the digits individually . 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Store ” . The system responds with “ Store, number please ” followed by a tone.
3. Say the first digit to be stored. The system will repeat back the digit it heard followed by a tone. Continue entering digits until the number to be stored is complete. . If an unwanted number is recognized by the system, say “ Clear ” at any time to clear the last number .
3. Say the name tag to be deleted. The system responds with “ Would you like to delete, <name tag>? Please say yes or no ” . . If the name tag is correct, say “ Y es ” to delete the name tag. The system responds with “ OK, deleting <name tag>, returning to the main menu.
Using the Digit Dial Command 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Digit Dial ” . The system responds with “ Digit dial using <phone name>, please say the first digit to dial ” followed by a tone.
Receiving a Call When an incoming call is received, the audio system mutes and a ring tone is heard in the vehicle. . Press b g and begin speaking to answer the call. . Press c x to ignore a call. Call W aiting Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work.
T o Mute a call 1. Press b g . The system responds with “ Ready ” followed by a tone. 2. Say “ Mute Call ” . The system responds with “ Call muted ” . T o Cancel Mute 1. Press b g . The system responds with “ Ready ” followed by a tone.
Dual T one Multi-Frequency (DTMF) T ones The in ‐ vehicle Bluetooth system can send numbers and numbers stored as name tags during a call. This is used when calling a menu driven phone system. Account numbers can be programmed into the phonebook for retrieval during menu driven calls.
Other Information The Bluetooth ® word mark and logos are owned by the Bluetooth ® SIG, Inc. and any use of such marks by General Motors is under license. Other trademarks and trade names are those of their respective owners. See Radio Frequency Statement on page 8 ‑ 17 for FCC information.
T o change radio stations: . Press and release w or x to go to the next or previous radio station stored as a preset. . Press and hold w or x to go to the next or previous radio station in the selected band with a strong signal. T o select tracks on a CD: Press and release w or x to go to the next or previous track.
Radio Reception Frequency interference and static can occur during normal radio reception if items such as cell phone chargers, vehicle convenience accessories, and external electronic devices are plugged into the accessory power outlet. If there is interference or static, unplug the item from the accessory power outlet.
Cellular Phone Usage Cellular phone usage may cause interference with the vehicle's radio. This interference may occur when making or receiving phone calls, charging the phone's battery , or simply having the phone on. This interference causes an increased level of static while listening to the radio.
2 NOTES 4-96.
Section 5 Driving Y our V ehicle Y our Driving, the Road, and the V ehicle . . . . . . . . . . 5-2 Defensive Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 D r u n k D r i v i n g ... ................................ 5 - 2 Control of a V ehicle .
Y our Driving, the Road, and the V ehicle Defensive Driving Defensive driving means “ always expect the unexpected. ” The first step in driving defensively is to wear your safety belt — See Safety Belts: They Are for Everyone on page 2 ‑ 14 . { W ARNING: Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes.
For persons under 21, it is against the law in every U.S. state to drink alcohol. There are good medical, psychological, and developmental reasons for these laws. The obvious way to eliminate the leading highway safety problem is for people never to drink alcohol and then drive.
Avoid needless heavy braking. Some people drive in spurts, heavy acceleration followed by heavy braking, rather than keeping pace with traffic. This is a mistake. The brakes might not have time to cool between hard stops. The brakes will wear out much faster with a lot of heavy braking.
Let us say the road is wet and you are driving safely . Suddenly , an animal jumps out in front of you. Y ou slam on the brakes and continue braking. Here is what happens with ABS: A computer senses that the wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each wheel.
Brake Assist If this vehicle has ESC with ABS, it also has a Brake Assist feature designed to assist the driver in stopping or decreasing vehicle speed in emergency driving conditions. This feature uses the stability system hydraulic brake control module to supplement the power brake system under conditions where the driver has quickly and forcefully applied the brake pedal in an attempt to quickly stop or slow down the vehicle.
This light flashes on the instrument panel cluster when the ESC system is on and activated. ESC activates when the computer senses a discrepancy between the intended path and the direction the vehicle is actually traveling. ESC selectively applies braking pressure at any one of the vehicle's brakes to help steer the vehicle in the intended direction.
When the ESC system is turned off, the TRACTION OFF and ESC OFF messages appear , and the ESC/TCS light comes on to warn the driver that both traction control and ESC are disabled. It is recommended that the system remain on for normal driving conditions, but it may be necessary to turn the system off if the vehicle is stuck in sand, mud, ice or snow , and you want to “ rock ” your vehicle to attempt to free it.
Launch Control (SS Models Only) Launch Control is a form of traction control, to control tire spin while launching the vehicle during closed track events and competitive driving. The feature is activated when the vehicle is at rest while in Competitive Mode.
If the vehicle is in cruise control while TCS begins to limit wheel spin, the cruise control will automatically disengage. The cruise control can be re-engaged when road conditions allow . See T urn Signal/Multifunction Lever on page 4 ‑ 4 . When this light is on and either the SERVICE TRACTION or TRACTION OFF message is displayed, the system will not limit wheel spin.
Notice: If the wheel(s) of one axle are allowed to spin excessively while the ESC/TCS, ABS and Brake warning lights and the SERVICE ESC and/or SERVICE TRACTION messages are displayed, the differential could be damaged. The repairs would not be covered by the vehicle warranty .
The ETS indicator/warning light may come on for the following reasons: . The indicator/warning light flashes while the traction control system is limiting wheel spin. . If the system is turned off by moving the shift lever to L (Low), the indicator/warning light comes on and stays on.
transmission is shifted to L (Low) or R (Reverse) to turn the system off, the indicator/warning light and TRACTION OFF will come on in L (Low). But the system will not turn off right away . It will wait until there is no longer a current need to limit wheel spin.
Steering Tips It is important to take curves at a reasonable speed. T raction in a curve depends on the condition of the tires and the road surface, the angle at which the curve is banked, and vehicle speed. While in a curve, speed is the one factor that can be controlled.
Off-Road Recovery The vehicle's right wheels can drop off the edge of a road onto the shoulder while driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy . Ease off the accelerator and then, if there is nothing in the way , steer so that the vehicle straddles the edge of the pavement.
Skidding In a skid, a driver can lose control of the vehicle. Defensive drivers avoid most skids by taking reasonable care suited to existing conditions, and by not overdriving those conditions. But skids are always possible. The three types of skids correspond to the vehicle's three control systems.
Racing or Other Competitive Driving See your warranty book before using your vehicle for racing or other competitive driving. After reviewing your warranty book, please see the GM Performance Parts website or catalog and contact the race sanctioning bodies, for example Sports Car Club of America (SCCA) or Grand American, for parts and equipment required for racing or other competitive driving.
Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate. Always drive slower in these types of driving conditions and avoid driving through large puddles and deep ‐ standing or flowing water .
Before Leaving on a Long T rip T o prepare your vehicle for a long trip, consider having it serviced by your dealer/retailer before departing. Things to check on your own include: . Windshield Washer Fluid: Reservoir full? Windows clean — inside and outside? .
Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on flat or rolling terrain. Tips for driving in these conditions include: . Keep the vehicle serviced and in good shape. . Check all fluid levels and brakes, tires, cooling system, and transmission.
Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 0°C (32°F) when freezing rain begins to fall, resulting in even less traction.
Blizzard Conditions Being stuck in snow can be in a serious situation. Stay with the vehicle unless there is help nearby . If possible, use the Roadside Assistance Program on page 8 ‑ 6 . T o get help and keep everyone in the vehicle safe: . T urn on the Hazard Warning Flashers on page 4 ‑ 3 .
T o save fuel, run the engine for only short periods as needed to warm the vehicle and then shut the engine off and close the window most of the way to save heat. Repeat this until help arrives but only when you feel really uncomfortable from the cold.
Rocking Y our V ehicle to Get It Out T urn the steering wheel left and right to clear the area around the front wheels. Turn off any traction system. Shift back and forth between R (Reverse) and a forward gear , or with a manual transmission, between 1 (First) or 2 (Second) and R (Reverse), spinning the wheels as little as possible.
Tire and Loading Information Label Label Example A vehicle specific Tire and Loading Information label is attached to the vehicle's center pillar (B-pillar). With the driver's door open, you will find the label attached below the door lock post (striker).
4. The resulting figure equals the available amount of cargo and luggage load capacity . For example, if the “ XXX ” amount equals 1400 lbs and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1400 − 750 (5 x 150) = 650 lbs).
Example 2 Item Description T otal A Maximum V ehicle Capacity Weight for Example 2 = 1,000 lbs (453 kg) B Subtract Occupant Weight @ 150 lbs (68 kg) × 5 = 750 lbs (340 kg) C Available Cargo Weight = .
positions. The combined weight of the driver , passengers, and cargo should never exceed your vehicle's maximum vehicle capacity weight. Certification Label A vehicle specific Certification/Tire label is found on the rear edge of the driver's door , or on the vehicle's center pillar (B ‐ pillar).
Notice : Overloadin g the vehicle may cause damage. Repairs would not be covered by the vehicle warranty . Do not overload the vehicle. If you put things inside your vehicle — like suitcases, tools, packages, or anything else — they will go as fast as the vehicle goes.
Recreational V ehicle T owing Recreational vehicle towing means towing the vehicle behind another vehicle – such as behind a motorhome. The two most common types of recreational vehicle towing are known as dinghy towing and dolly towing. Dinghy towing is towing the vehicle with all four wheels on the ground.
T o prevent the battery from draining while the vehicle is being towed, remove the following fuse from the floor console fuse block: 8 (Ignition Switch, P ASS ‐ Key ® III+). See Floor Console Fuse Block on page 6 ‑ 120 for more information. Remember to reinstall the fuse once the destination has been reached.
T owing a T railer (Automatic T ransmission) { W ARNING: The driver can lose control when pulling a trailer if the correct equipment is not used or the vehicle is not driven properly . For example, if the trailer is too heavy , the brakes may not work well — or even at all.
Pulling A T railer Here are some important points: . There are many different laws, including speed limit restrictions, having to do with trailering. Make sure the rig will be legal, not only where you live but also where you will be driving. A good source for this information can be state or provincial police.
Weight of the T railer T ongue The tongue load (A) of any trailer is an important weight to measure because it affects the total gross weight of the vehicle. The Gross V ehicle Weight (GVW) includes the curb weight of the vehicle, any cargo carried in it, and the people who will be riding in the vehicle.
T railering may be limited by the vehicle's ability to carry tongue weight. T ongue weight cannot cause the vehicle to exceed the GVWR (Gross V ehicle Weight Rating) or the RGA WR (Rear Gross Axle Weight Rating). The effect of additional weight may reduce the trailering capacity more than the total of the additional weight.
But the effect on the rear axle must still be considered. Because the rear axle now weighs 3,100 lbs (1 406 kg), 900 lbs (408 kg) can be put on the rear axle without exceeding RGAWR. The effect of tongue weight is about 1.5 times the actual weight. Dividing the 900 lbs (408 kg) by 1.
Safety Chains Always attach chains between the vehicle and the trailer . Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch. Always leave just enough slack so the rig can turn.
Backing Up Hold the bottom of the steering wheel with one hand. Then, to move the trailer to the left, move that hand to the left. T o move the trailer to the right, move your hand to the right. Always back up slowly and, if possible, have someone guide you.
Parking on Hills { W ARNING: Parking the vehicle on a hill with the trailer attached can be dangerous. If something goes wrong, the rig could start to move. People can be injured, and both the vehicle and the trailer can be damaged. When possible, always park the rig on a flat surface.
Maintenance When T railer T owing The vehicle needs service more often when pulling a trailer . See this manual's Maintenance Schedule or Index for more information. Things that are especially important in trailer operation are automatic transmission fluid, engine oil, axle lubricant, belts, cooling system and brake system.
Section 6 Service and Appearance Care Service ......... ........................... ......... 6-3 Accessories and Modifications . . . . . . . . . . . . . . . . . . 6-3 California Proposition 65 Warning . . . . . . . . . . . . . . . 6-4 California Perchlorate Materials R e q u i r e m e n t s .
Section 6 Service and Appearance Care When It Is T ime for New Tires . . . . . . . . . . . . . . . . . 6-71 Buying New T ires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-72 Different Size Tires and Wheels . . . . . . . . . . . . . . .
Service For service and parts needs, visit your dealer/retailer . Y ou will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modifications When non ‐ dealer/non ‐ retailer accessories are added to the vehicle, they can affect vehicle performance and safety , including such things as airbags, braking, stability , ride and handling, emissions systems, aerodynamics, durability , and electronic systems like antilock brakes, traction control, and stability control.
California Proposition 65 W arning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals.
Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Record on page 7 ‑ 14 . Adding Equipment to the Outside of the V ehicle Things added to the outside of the vehicle can affect the airflow around it.
If the vehicle has the 2.2L L4 engine (VIN Code B) or the 2.4L L4 engine (VIN Code V), you can use either unleaded gasoline or ethanol fuel containing up to 85% ethanol (E85). See Fuel E85 (85% Ethanol) on page 6 ‑ 8 . If the vehicle has the 2.0L L4 engine (VIN Code M), use only unleaded gasoline.
California Fuel If the vehicle is certified to meet California Emissions Standards, it is designed to operate on fuels that meet California specifications. See the underhood emission control label. If this fuel is not available in states adopting California emissions standards, the vehicle will operate satisfactorily on fuels meeting federal specifications, but emission control system performance might be affected.
Some gasolines that are not reformulated for low emissions can contain an octane-enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT); ask the attendant where you buy gasoline whether the fuel contains MMT . We recommend against the use of such gasolines.
T o ensure quick starts in the wintertime, the E85 fuel must be formulated properly for your climate according to ASTM specification D 5798. If you have trouble starting on E85, it could be because the E85 fuel is not properly formulated for your climate.
Filling the T ank { W ARNING: Fuel vapor burns violently and a fuel fire can cause bad injuries. T o help avoid injuries to you and others, read and follow all the instructions on the fuel pump island. Turn off the engine when refueling. Do not smoke near fuel or when refueling the vehicle.
The tethered fuel cap is located behind a hinged fuel door on the passenger side of the vehicle. If the vehicle has E85 fuel capability , the fuel cap will be yellow and state that E85 or gasoline can be used. See Fuel E85 (85% Ethanol) on page 6 ‑ 8 .
When replacing the fuel cap, turn it clockwise until it clicks. Make sure the cap is fully installed. The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere.
Filling a Portable Fuel Container { W ARNING: Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor . Y ou can be badly burned and the vehicle damaged if this occurs.
Checking Things Under the Hood { W ARNING: An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing, and tools away from any underhood electric fan. { W ARNING: Things that burn can get on hot engine parts and start a fire.
Hood Release T o open the hood, do the following. 1. Pull the interior hood release lever with this symbol on it. It is located to the left of the instrument panel on the driver's side of the vehicle. 2. Then go to the front of the vehicle and push the secondary hood release lever to the left.
Engine Compartment Overview When you open the hood on the 2.4L engine (2.2L engine similar), here is what you will see: 6-16.
A. Windshield W asher Fluid Reservoir . See “ Adding W asher Fluid ” under Windshield Washer Fluid on page 6 ‑ 36 . B. Pressure Cap. See Cooling System on page 6 ‑ 28 . C. Coolant Recovery T ank. See “ Checking Coolant ” under Engine Coolant on page 6 ‑ 29 .
When you open the hood on the 2.0L L4 engine, this is what you will see: 6-18.
A. Pressure Cap. See Cooling System on page 6 ‑ 28 . B. Engine Air Cleaner/Filter . See Engine Air Cleaner/Filter on page 6 ‑ 25 . C. Windshield W asher Fluid Reservoir . See “ Adding W asher Fluid ” under Windshield Washer Fluid on page 6 ‑ 36 .
When to Add Engine Oil If the oil is below the MIN (minimum) mark, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity , see Capacities and Specifications on page 6 ‑ 125 .
What Kind of Engine Oil to Use For V ehicles With the 2.2L or 2.4L L4 Engine Look for three things: . GM6094M Use only an oil that meets GM Standard GM6094M. . SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity , or thickness.
For V ehicles with the 2.0L L4 Engine Only Look for three things: . GM4718M This vehicle's engine requires a special oil meeting GM Standard GM4718M, such as Mobil 1 ® or equivalent. Oils meeting this standard may be identified as synthetic. However , not all synthetic oils will meet this GM standard.
Cold T emperature Operation For V ehicles With the 2.2L or 2.4L L4 Engine If in an area of extreme cold, where the temperature falls below − 20°F ( − 29°C), use either an SAE 5W-30 synthetic oil or an SAE 0W-30 engine oil. Both provide easier cold starting for the engine at extremely low temperatures.
If the system is ever reset accidentally , the oil must be changed at 3,000 miles (5 000 km) since the last oil change. Remember to reset the oil life system whenever the oil is changed. How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change your engine oil and filter based on vehicle use.
What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer . Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water , or a good hand cleaner .
Because this operation can be a little difficult, you may choose to have this done at the dealer/retailer service department. T o inspect or replace the filter , do the following: 1. Disconnect the Mass Air Flow sensor , PCV hose, and both ducts. 2. Pull the entire system from the top of the engine.
T o inspect or replace the filter , do the following: 1. Remove the screws that hold the housing and cover together and lift off the cover. 2. Inspect or replace the engine air cleaner/filter . 3. Reverse the steps to reinstall the system. Be sure to reinstall the housing tightly .
Manual T ransmission Fluid It is not necessary to check the manual transmission fluid level. A transmission fluid leak is the only reason for fluid loss. If a leak occurs, take the vehicle to a dealer/retailer for service. Have it repaired as soon as possible.
{ W ARNING: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury . Keep hands, clothing, and tools away from any underhood electric fan. { W ARNING: Heater and radiator hoses, and other engine parts, can be very hot.
What to Use { W ARNING: Adding only plain water to the cooling system can be dangerous. Plain water , or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle's coolant warning system is set for the proper coolant mixture.
Checking Coolant The vehicle must be on a level surface when checking the coolant level. The coolant recovery tank cap has this symbol on it. The tank is located in the engine compartment toward the front of the engine on the passenger's side of the vehicle.
How to Add Coolant to the Cooling System { W ARNING: Y ou can be burned if you spill coolant on hot engine parts. Coolant contains ethylene glycol and it will burn if the engine parts are hot enough. Do not spill coolant on a hot engine. Notice: This vehicle has a specific coolant fill procedure.
If no coolant is visible in the coolant recovery tank, add coolant at the pressure cap as follows: 1. Remove the pressure cap when the cooling system, including the pressure cap and upper radiator hose, is no longer hot. T urn the pressure cap slowly counterclockwise.
7. Start the engine and let it run until you can feel the upper radiator hose getting hot. W atch out for the engine cooling fan. 8. By this time, the coolant level inside the radiator filler port may be lower . If the level is lower , add more of the proper DEX-COOL ® coolant mixture through the fill port until the level reaches the base of the fill port.
If Steam Is Coming From The Engine Compartment { W ARNING: Steam from an overheated engine can burn you badly , even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down.
If the temperature overheat gauge is no longer in the overheat zone or an overheat warning no longer displays, the vehicle can be driven. Continue to drive the vehicle slow for about 10 minutes. Keep a safe vehicle distance from the car in front of you.
Brakes Brake Fluid The brake master cylinder and, on manual transmission vehicles, the clutch hydraulic system use the same reservoir . See Engine Compartment Overview on page 6 ‑ 16 for the location of the reservoir . The reservoir is filled with DOT 3 brake fluid.
What to Add Use only new DOT 3 brake fluid from a sealed container . See Recommended Fluids and Lubricants on page 7 ‑ 10 . Always clean the brake fluid reservoir cap and the area around the cap before removing it. This helps keep dirt from entering the reservoir .
Brake Wear This vehicle has front disc brakes and could have rear drum brakes or rear disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal firmly .
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. The vehicle was designed and tested with top-quality brake parts. When parts of the braking system are replaced — for example, when the brake linings wear down and new ones are installed — be sure to get new approved replacement parts.
Jump Starting If the vehicle's battery has run down, you may want to use another vehicle and some jumper cables to start the vehicle. Be sure to use the following steps to do it safely . { W ARNING: Batteries can hurt you. They can be dangerous because: .
4. Open the hood on the other vehicle and locate the positive (+) and negative ( − ) terminal locations on that vehicle. Y ou will not see the battery of your vehicle under the hood. It is located in the rear cargo area. Y ou will not need to access your battery for jump starting.
{ W ARNING: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Be sure the battery has enough water . Y ou do not need to add water to the battery installed in your new vehicle.
6. Connect the red positive (+) cable to the positive (+) terminal location on the vehicle with the dead battery . Use a remote positive (+) terminal if the vehicle has one. 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery .
T o disconnect the jumper cables from both vehicles: 1. Disconnect the black negative ( − ) cable from the vehicle that had the dead battery . 2. Disconnect the black negative ( − ) cable from the vehicle with the good battery . 3. Disconnect the red positive (+) cable from the vehicle with the good battery .
Headlamp aiming is done with the vehicle's low-beam headlamps. The high-beam headlamps will be correctly aimed if the low-beam headlamps are aimed properly . T o adjust the vertical aim: 1. Open the hood. See Hood Release on page 6 ‑ 15 for more information.
Driver Side Shown 7. Locate the vertical headlamp aiming screws, which are under the hood near each headlamp assembly . The adjustment screw can be turned with a 6 mm hex socket. 8. T urn the vertical aiming screw until the headlamp beam is aimed to the horizontal tape line.
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 6 ‑ 53 . For any bulb changing procedure not listed in this section, contact your dealer/retailer . Halogen Bulbs { W ARNING: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb.
T o replace the headlamp, turn signal, or parking lamp bulb: 1. T urn the wheel to access the wheel well. 2. Remove the fasteners located on the wheel liner . T o access the headlamp and the turn signal/parking lamp bulbs. 3. Reach in behind the wheel well liner and locate the bulb to be changed.
Center High-Mounted Stoplamp (CHMSL) T o replace the center high-mounted stoplamp bulb: 1. Open the liftgate. See Liftgate on page 3 ‑ 13 . 2. Remove the center trim located near the top of the liftgate. 3. T urn the bulb socket counterclockwise and pull it straight out of the lamps assembly .
T aillamps, T urn Signal, Stoplamps and Back-up Lamps A. Stoplamp/T aillamp/T urn Signal Lamp B. Back-up Lamp T o replace one of these bulbs: 1. Open the liftgate. See Liftgate on page 3 ‑ 13 . 2. Remove the cover in the rear cargo area of the vehicle to access the bulbs.
4. Pull the bulb straight out of the socket. 5. Install a new bulb. When installing the bulb socket into the assembly , line up the tabs with the slots in the bulb assembly . 6. Push the bulb socket straight into the lamp assembly and turn it clockwise to lock it into place.
5. Push and turn the license plate back through the fascia opening. 6. Reinstall the two screws holding the license plate lamps to the fascia. Replacement Bulbs Exterior Lamp Bulb Number Back-up Lamp and CHMSL 921 Front T urn Signal and Parking Lamp (Amber) 5702KA Front T urn Signal and Parking Lamp (Clear) B2N Headlamp High/Low-Beam H13 Stoplamp/T aillamp/T urn Signal 3057KX For replacement bulbs not listed here, contact your dealer/retailer .
Backglass Wiper Blade Replacement 1. Remove the protective cap from the wiper arm. If the protective cap is not removed before lifting the wiper arm, the wiper arm could be damaged. 2. Pull the wiper arm away from the backglass and into the service position.
W ARNING: (Continued) . Underinflated tires pose the same danger as overloaded tires. The resulting accident could cause serious injury . Check all tires frequently to maintain the recommended pressure. Tire pressure should be checked when your vehicle's tires are cold.
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The examples below show a typical passenger vehicle tire and a compact spare tire sidewall. Passenger (P ‐ Metric) Tire Example (A) Tire Size : The tire size is a combination of letters and numbers used to define a particular tire's width, height, aspect ratio, construction type, and service description.
(D) Tire Identification Number (TIN) : The letters and numbers following DOT (Department of T ransportation) code is the Tire Identification Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture.
(B) Tire Ply Material : The type of cord and number of plies in the sidewall and under the tread. (C) Tire Identification Number (TIN) : The letters and numbers following the DOT (Department of T ransportation) code is the Tire Identification Number (TIN).
Tire Size The following illustration shows an example of a typical passenger vehicle tire size. (A) Passenger (P ‐ Metric) Tire : The United States version of a metric tire sizing system. The letter P as the first character in the tire size means a passenger vehicle tire engineered to standards set by the U.
Tire T erminology and Definitions Air Pressure : The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight : This means the combined weight of optional accessories.
GA WR RR : Gross Axle Weight Rating for the rear axle. See Loading the Vehicle on page 5 ‑ 24 . Intended Outboard Sidewall : The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa) : The metric unit for air pressure.
Recommended Inflation Pressure : V ehicle manufacturer's recommended tire inflation pressure as shown on the tire placard. See Inflation - Tire Pressure on page 6 ‑ 63 and Loading the V ehicle on page 5 ‑ 24 . Radial Ply Tire : A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread.
Inflation - Tire Pressure T ires need the correct amount of air pressure to operate effectively . Notice: Do not let anyone tell you that under ‐ inflation or over ‐ inflation is all right. It is not. If your tires do not have enough air (under ‐ inflation), you can get the following: .
How to Check Use a good quality pocket-type gauge to check tire pressure. Y ou cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are under ‐ inflated. Check the tire's inflation pressure when the tires are cold.
Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under ‐ inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
If the warning light comes on, stop as soon as possible and inflate the tires to the recommended pressure shown on the tire loading information label. See Loading the Vehicle on page 5 ‑ 24 . At the same time a message to check the pressure in a specific tire appears on the Driver Information Center (DIC) display .
TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle.
TPMS Sensor Matching Process Each TPMS sensor has a unique identification code. Any time you replace one or more of the TPMS sensors or rotate the vehicle's tires, the identification codes need to be matched to the new tire/wheel location. The sensors are matched, to the tire/wheel locations, in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear tire using a TPMS diagnostic tool.
8. The driver side rear turn signal comes on to indicate that corner sensor is ready to be learned. Proceed to the driver side rear tire, and repeat the procedure in Step 5. 9. After hearing the single horn chirp for the driver side rear tire, two additional horn chirps sound to indicate the tire learning process is done.
When rotating the vehicle's tires, always use the correct rotation pattern shown here. Do not include the compact spare tire in the tire rotation. After the tires have been rotated, adjust the front and rear inflation pressures as shown on the T ire and Loading Information label.
When It Is Time for New T ires V arious factors, such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions influence when you need new tires. One way to tell when it is time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.
Buying New Tires GM has developed and matched specific tires for your vehicle. The original equipment tires installed on your vehicle, when it was new , were designed to meet General Motors T ire Performance Criteria Specification (TPC Spec) system rating.
{ W ARNING: If you use bias-ply tires on the vehicle, the wheel rim flanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly , causing a crash. Use only radial-ply tires with the wheels on the vehicle. If you must replace your vehicle's tires with those that do not have a TPC Spec number , make sure they are the same size, load range, speed rating, and construction type (radial and bias ‐ belted tires) as your vehicle's original tires.
Different Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this could affect the way your vehicle performs, including its braking, ride and handling characteristics, stability , and resistance to rollover .
All Passenger Car Tires Must Conform to Federal Safety Requirements In Addition T o These Grades. T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Wheel Alignment and Tire Balance The tires and wheels on your vehicle were aligned and balanced carefully at the factory to give you the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis.
Used Replacement Wheels { W ARNING: Putting a used wheel on the vehicle is dangerous. Y ou cannot know how it has been used or how far it has been driven. It could fail suddenly and cause a crash. If you have to replace a wheel, use a new GM original equipment wheel.
A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you would use in a skid. In any rear blowout remove your foot from the accelerator pedal. Get the vehicle under control by steering the way you want the vehicle to go.
{ W ARNING: Storing the tire sealant and compressor kit or other equipment in the passenger compartment of the vehicle could cause injury . In a sudden stop or collision, loose equipment could strike someone. Store the tire sealant and compressor kit in its original location.
Tire Sealant Read and follow the safe handling instructions on the label adhered to the compressor . Check the tire sealant expiration date on the sealant canister . The sealant canister should be replaced before its expiration date. Replacement sealant canisters are available at your local dealer/retailer .
Always do a safety check first. See If a Tire Goes Flat on page 6 ‑ 77 . Do not remove any objects that have penetrated the tire. 1. Remove the tire sealant and compressor kit from its storage location. See Tire Sealant and Compressor Kit Storage on page 6 ‑ 87 .
9. Press the on/off (A) button to turn the tire sealant and compressor kit on. The compressor will inject sealant and air into the tire. The pressure gauge (D) will initially show a high pressure while the compressor pushes the sealant into the tire. Once the sealant is completely dispersed into the tire, the pressure will quickly drop and start to rise again as the tire inflates with air only .
14. Replace the tire valve stem cap. 15. Replace the sealant/air hose (F), and the power plug (G) back in their original location. 16. If the flat tire was able to inflate to the recommended inflation pressure, remove the maximum speed label from the sealant canister and place it in a highly visible location.
Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured) T o use the air compressor to inflate a tire with air only and not sealant: Always do a safety check first. See If a Tire Goes Flat on page 6 ‑ 77 . 1. Remove the tire sealant and compressor kit from its storage location.
7. Start the vehicle. The vehicle must be running while using the air compressor . 8. T urn the selector switch (B) counterclockwise to the Air Only position. 9. Press the on/off (A) button to turn the compressor on. The compressor will inflate the tire with air only .
Removal and Installation of the Sealant Canister T o remove the sealant canister: 1. Remove the plastic cover . 2. Unscrew the connector (B) from the canister (A). 3. Pull up on the canister (A) to remove it. 4. Replace with a new canister which is available from your dealer/retailer .
Tire Sealant and Compressor Kit Storage The tire sealant and compressor kit is located in the rear compartment storage area. 1. Open the liftgate. See Liftgate on page 3 ‑ 13 . 2. Lift the storage cover . 3. T urn the retainer clockwise and remove the tire sealant and compressor kit.
Changing a Flat Tire If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 4 ‑ 3 . { W ARNING: Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall on you or other people.
A. Wheel Block B. Flat T ire The following information explains how to use the jack and change a tire. Removing the Spare Tire and T ools The jack, wheel wrench, and spare tire are stowed in the rear of the vehicle, underneath the floor of the cargo area.
3. T urn the retainer counterclockwise to remove the tire cover . 4. Remove the tire cover . 5. Remove the spare tire by placing your hands at the four and eight o'clock positions. Gently pull it up and out of the trunk. See Compact Spare Tire on page 6 ‑ 1 10 .
T urn the plastic wheel nut counterclockwise to loosen the wheel wrench from the jack. Press the button and then pull on the end of the wheel wrench to extend the handle.
Removing the Flat Tire and Installing the Spare Tire (All Models Except SS) 1. Do a safety check before proceeding. See Changing a Flat Tire on page 6 ‑ 88 for more information. 2. Using the wheel wrench, loosen all the wheel nuts. Do not remove them yet.
{ W ARNING: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. { W ARNING: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall.
5. Remove all the wheel nuts and take off the flat tire. { W ARNING: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
6. Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel. 7. Place the compact spare tire on the wheel-mounting surface. { W ARNING: Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash.
{ W ARNING: Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque specification supplied by the aftermarket manufacturer when using accessory locking wheel nuts.
T o change the rear road tire: Rear Tire Changing Procedure 1. Do a safety check before proceeding. See Changing a Flat Tire on page 6 ‑ 88 for more information. 2. Using the wheel wrench, loosen all the wheel nuts on the rear tire. Do not remove them yet.
{ W ARNING: Raising your vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. T o help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.
5. Remove all the wheel nuts and take off the tire. 6. Install the compact spare tire. { W ARNING: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident.
{ W ARNING: Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash. 9. Reinstall the wheel nuts with the rounded end of the nuts toward the wheel. T ighten each nut by hand until the wheel is held against the hub.
1 1. T ighten the wheel nuts firmly in a crisscross sequence as shown. T o change the front flat tire: Front Tire Changing Procedure 1. Perform a rear tire change by removing the rear tire and installing the compact spare tire in the rear wheel location.
3. Position the jack on the front position and raise the jack lift head to fit over the car flange under the down arrow markings on the rocker panel. { W ARNING: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed.
4. Raise the vehicle by turning the jack handle clockwise. Raise the vehicle far enough off the ground so there is enough room for the tire. 5. Remove all the wheel nuts and take off the flat tire.
{ W ARNING: Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle.
10. Lower the vehicle by turning the jack handle counterclockwise. Lower the jack completely . { W ARNING: Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing.
Storing a Flat or Spare Tire and T ools { W ARNING: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury . In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.
5. Route the loop end of the strap (C) through one of the cargo tie-downs (A) located in the rear of the vehicle. 6. Route the hook (B) through the loop (C).
Steel Wheel 8. Route the hook end of the strap through the wheel. 9. Attach the strap to the cargo tie-downs in the rear of the vehicle. 10. Slide the buckle to tighten the tie-down strap.
Storing the Compact Spare Tire and T ools Use the diagram as a guide for storing the compact spare tire once you are done using it. A. Retainer B. Cover C. Spare T ire D. Wing Nut E. Jack and Wheel Wrench F . Strap G. Bolt 1. Open the liftgate. See Liftgate on page 3 ‑ 13 for more information.
Compact Spare Tire { W ARNING: Driving with more than one compact spare tire at a time could result in loss of braking and handling. This could lead to a crash and you or others could be injured. Use only one compact spare tire at a time. If this vehicle has a compact spare tire it was fully inflated when the vehicle was new , however , it can lose air after a time.
Appearance Care Interior Cleaning The vehicle's interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on the upholstery . Dirt can damage carpet, fabric, leather , and plastic surfaces.
. Laundry detergents or dishwashing soaps with degreasers can leave residue that streaks and attracts dirt. For liquid cleaners, about 20 drops per gallon (3.78 L) of water is a good guide. Use only mild, neutral-pH soaps. . T oo much cleaner that saturates the upholstery .
Leather A soft cloth dampened with water can be used to remove dust. If a more thorough cleaning is necessary , a soft cloth dampened with a mild soap solution can be used. Allow the leather to dry naturally . Do not use heat to dry . Never use steam to clean leather .
Weatherstrips Silicone grease on weatherstrips will make them last longer , seal better , and not stick or squeak. Apply silicone grease with a clean cloth. During very cold, damp weather frequent application may be required. See Recommended Fluids and Lubricants on page 7 ‑ 10 .
Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/clearcoat paint finish on the vehicle. Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar , tree sap, bird droppings, chemicals from industrial chimneys, etc.
Aluminum or Chrome-Plated Wheels and T rim The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water . Rinse with clean water . After rinsing thoroughly , dry with a soft clean towel.
Tires T o clean the tires, use a stiff brush with tire cleaner . Notice: Using petroleum-based tire dressing products on the vehicle may damage the paint finish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on the vehicle.
V ehicle Identification V ehicle Identification Number (VIN) This legal identifier is in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside. The VIN also appears on the V ehicle Certification and Service Parts labels and certificates of title and registration.
The vehicle has an airbag system. Before attempting to add anything electrical to the vehicle, see Servicing Y our Airbag-Equipped Vehicle on page 2 ‑ 76 and Adding Equipment to Y our Airbag-Equipped Vehicle on page 2 ‑ 77 . Headlamp Wiring The headlamp wiring is protected by fuses in the fuse block.
Floor Console Fuse Block The floor console fuse block is located on the passenger side of the floor console behind the forward panel. The panel has four clips, one in each corner . Pull the panel to disconnect the four clips, and access the fuses. Use the fuse puller to remove fuses.
Fuses Usage 1 Fuse Puller 2 Empty 3 Empty 4 Empty 5 Empty 6 Amplifier 7 Cluster 8 Ignition Switch, P ASS-Key ® III+ 9 Stoplamp 10 Heating, V entilation, Air Conditioning, P ASS-Key ® III+ 1 1 Empty .
Engine Compartment Fuse Block The underhood fuse block is located on the driver side of the engine compartment. Lift the cover to access the fuse/relay block. Notice: Spilling liquid on any electrical components on the vehicle may damage it. Always keep the covers on any electrical component.
Fuses Usage 36 Power Windows 37 Power Seat (Option) 40 Cooling Fan 41 Engine Control Module 42 Cam Phaser (Turbo Only) 43 Engine Control Module, Transmission 44 Antilock Brake System (Option) 45 Injec.
Relays Usage 14 Rear Defogger Relay 15 Air Conditioning Clutch 16 Empty 17 Rear Wiper 18 Liftgate Release 19 Fuel Pump 24 Empty 26 Powertrain 28 Daytime Running Lamps 34 Starting System 35 Empty 38 Empty 39 Windshield W asher Pump 48 Rear Windshield W asher 50 Cooling Fan 51 Run, Crank Relays Usage 52 Windshield Wiper 54 Fog Lamps (Option) 55 Horn 68 Parking Lamps 70 Windshield Wipers 71 Headlamp Low-Beam 72 Headlamp High-Beam A Center High-Mounted Stoplamp Relay , and a Rear Access Panel Door Interlock Relay (Panel V an only), are located underhood in front of the left shock tower .
Capacities and Specifications The following approximate capacities are given in English and metric conversions. Please refer to Maintenance Replacement Parts on page 7 ‑ 12 for more information. Application Capacities English Metric Air Conditioning Refrigerant R134a For the air conditioning system refrigerant charge amount, see the refrigerant caution label located under the hood.
Engine Specifications Engine VIN Code T ransmission Spark Plug Gap 2.0L L4 Engine M Automatic Manual 0.035 in (0.90 mm) 2.2L L4 Engine B Automatic Manual 0.
Section 7 Maintenance Schedule Maintenance Schedule ........................ .... 7-2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Scheduled Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Owner Checks and Services .
Maintenance Schedule Introduction Notice: Maintenance intervals, checks, inspections, recommended fluids, and lubricants are necessary to keep this vehicle in good working condition. Damage caused by failure to follow scheduled maintenance might not be covered by the vehicle warranty .
Rotation of New Tires T o maintain ride, handling, and performance of the vehicle, it is important that the first rotation service for new tires be performed when they have 8 000 to 13 000 km (5,000 to 8,000 miles). See Tire Inspection and Rotation on page 6 ‑ 69 .
Maintenance I . Change engine oil and filter . See Engine Oil on page 6 ‑ 19 . An Emission Control Service. . Engine coolant level check. See Engine Coolant on page 6 ‑ 29 . . Windshield washer fluid level check. See Windshield Washer Fluid on page 6 ‑ 36 .
. Passenger compartment air filter replacement (or every 12 months, whichever occurs first). More frequent replacement may be required if vehicle is driven regularly under dusty conditions. . 2.2L and 2.4L Engines: Engine air cleaner filter inspection (vehicles not driven in dusty conditions).
First Engine Oil Change After Every 40 000 km/25,000 Miles . Fuel system inspection for damage or leaks. First Engine Oil Change After Every 80 000 km/50,000 Miles . Engine air cleaner filter replacement. See Engine Air Cleaner/Filter on page 6 ‑ 25 .
Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and filter . Reset oil life system. • • Engine coolant level check. • • Windshield washer fluid level check. • • T ire inflation pressures check. • • T ire wear inspection.
Owner Checks and Services Starter Switch Check { W ARNING: When you are doing this inspection, the vehicle could move suddenly . If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle.
Ignition T ransmission Lock Check While parked, and with the parking brake set, try to turn the ignition to LOCK/OFF in each shift lever position. . For automatic transmission vehicles, the ignition should turn to LOCK/OFF only when the shift lever is in P (Park).
Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number , or specification can be obtained from your dealer/retailer . Usage Fluid/Lubricant Engine Oil (2.2L and 2.4L L4 engines) Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute (API) Certified for Gasoline Engines starburst symbol.
Usage Fluid/Lubricant Automatic T ransmission DEXRON ® -VI Automatic T ransmission Fluid. Key Lock Cylinders Multi-Purpose Lubricant, Superlube (GM Part No. U.S. 12346241, in Canada 10953474). Manual T ransmission Shift Linkage Chassis Lubricant (GM Part No.
Maintenance Replacement Parts Replacement parts identified below by name, part number , or specification can be obtained from your dealer/retailer . Maintenance Replacement Parts Part GM Part Number ACDelco Part Number Engine Air Cleaner/Filter 2.0L Engine 15909459 — 2.
Engine Drive Belt Routing Dotted line shows routing for vehicles without air conditioning. 7-13.
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided.
Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 7-15.
Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 7-16.
Section 8 Customer Assistance Information Customer Assistance and Information . . . . . . . . . . . 8-2 Customer Satisfaction Procedure . . . . . . . . . . . . . . . 8-2 Online Owner Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 Customer Assistance for T ext T elephone (TTY) Users .
Customer Assistance and Information Customer Satisfaction Procedure Y our satisfaction and goodwill are important to your dealer and to Chevrolet. Normally , any concerns with the sales transaction or the operation of the vehicle will be resolved by the dealer's sales or service departments.
If you do not agree with the decision given in your case, you may reject it and proceed with any other venue for relief available to you. Y ou may contact the BBB Auto Line Program using the toll-free telephone number or write them at the following address: BBB Auto Line Program Council of Better Business Bureaus, Inc.
Online Owner Center Online Owner Center (U.S.) — www .gmownercenter .com/chevrolet Information and services customized for your specific vehicle — all in one convenient place. . Digital owner manual, warranty information, and more . Online service and maintenance records .
Customer Assistance for T ext T elephone (TTY) Users T o assist customers who are deaf, hard of hearing, or speech-impaired and who use T ext T elephones (TTYs), Chevrolet has TTY equipment available at its Customer Assistance Center . Any TTY user in the U.
Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.V . Customer Assistance Center Paseo de la Reforma # 2740 Col. Lomas de Bezares C.P .
. Model, year , color, and license plate number of the vehicle . Odometer reading, V ehicle Identification Number (VIN), and delivery date of the vehicle . Description of the problem Coverage Services are provided up to 5 years/100,000 miles (160 000 km), whichever comes first.
Services Not Included in Roadside Assistance . Impound towing caused by violation of any laws. . Legal fines. . Mounting, dismounting or changing of snow tires, chains, or other traction devices. . T owing or services for vehicles driven on a non-public road or highway .
If your vehicle cannot be scheduled into the service department immediately , keep driving it until it can be scheduled for service, unless, of course, the problem is safety-related. If it is, please call your dealership/ retailer , let them know this, and ask for instructions.
Claim amounts should reflect actual costs and be supported by original receipts. See your dealer for information regarding the allowance amounts for reimbursement of fuel or other transportation costs. Courtesy Rental V ehicle Y our dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle that you obtain if your vehicle is kept for an overnight warranty repair .
of the vehicle. A recycled original equipment GM part, may be an acceptable choice to maintain your vehicle's originally designed appearance and safety performance, however , the history of these parts is not known. Such parts are not covered by your GM New V ehicle Limited W arranty , and any related failures are not covered by that warranty .
If a Crash Occurs Here is what to do if you are involved in a crash. . Check to make sure that you are all right. If you are uninjured, make sure that no one else in your vehicle, or the other vehicle, is injured. . If there has been an injury , call emergency services for help.
Managing the V ehicle Damage Repair Process In the event that your vehicle requires damage repairs, GM recommends that you take an active role in its repair . If you have a pre-determined repair facility of choice, take your vehicle there, or have it towed there.
Reporting Safety Defects to the Canadian Government If you live in Canada, and you believe that your vehicle has a safety defect, notify Transport Canada immediately , in addition to notifying General Motors of Canada Limited. Call them at 1-800-333-0510 or write to: T ransport Canada Road Safety Branch 2780 Sheffield Road Ottawa, Ontario K1B 3V9 Reporting Safety Defects to General Motors In addition to notifying NHTSA (or Transport Canada) in a situation like this, please notify General Motors.
In-Portfolio: Includes a Portfolio, Owner Manual, and W arranty Booklet. RET AIL SELL PRICE: $35.00 (U.S.) plus processing fee Without Portfolio: Owner Manual only . RET AIL SELL PRICE: $25.00 (U.S.) plus processing fee Current and Past Model Order Forms T echnical Service Bulletins and Manuals are available for current and past model GM vehicles.
Event Data Recorders This vehicle has an Event Data Recorder (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an airbag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle's systems performed.
Navigation System If your vehicle has a navigation system, use of the system may result in the storage of destinations, addresses, telephone numbers, and other trip information. Refer to the navigation system operating manual for information on stored data and for deletion instructions.
2 NOTES 8-18.
A Accessories and Modifications . . . . . . . . . . . . . . . . . . . . . . . 6-3 Accessory Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25 Accessory Power Outlets . . . . . . . . . . . . . . . . . . . . . . . . . . 4-16 Add-On Electrical Equipment .
Audio System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-60 Audio Steering Wheel Controls . . . . . . . . . . . . . . . . . . . 4-92 Radio Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-94 Setting the Clock .
Carbon Monoxide Engine Exhaust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-39 Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13 Winter Driving . . . . . . . . . . . . . . . .
Coolant Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-29 Engine T emperature Gauge . . . . . . . . . . . . . . . . . . . . . . 4-34 Engine T emperature Warning Light . . . . . . . . . . . . . . . 4-34 Cooling System .
E E85 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8 EDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15 Electrical Equipment, Add-On . . . . . . . .
Fog Lamps Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13 Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39 Folding Rear Seat . . . . . . . . . . . . . . . . . .
Headlamps (cont.) High/Low Beam Changer . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 On Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12 Wiper Activated . . . . . . . . . . . . . . . . . . . . . . . . .
Lap-Shoulder Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-28 LA TCH System for Child Restraints . . . . . . . . . . . . . . . . 2-45 Liftgate Carbon Monoxide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mirrors Automatic Dimming Rearview . . . . . . . . . . . . . . . . . . . . . 3-41 Manual Rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-41 Outside Convex Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43 Outside Power Mirrors .
Power Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10 Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 19 Lumbar Controls . . . . . . . . . . . . . . . . . . . . . . . .
Restraint System Check Checking the Restraint Systems . . . . . . . . . . . . . . . . . . 2-78 Replacing Restraint System Parts After a Crash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-79 Retained Accessory Power (RAP) .
Service (cont.) Parts Identification Label . . . . . . . . . . . . . . . . . . . . . . . . 6-1 18 Publications Ordering Information . . . . . . . . . . . . . . . . . 8-14 Scheduling Appointments . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8 Servicing Y our Airbag-Equipped V ehicle .
T ires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-54 Aluminum or Chrome-Plated Wheels, Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 16 Buying New T ires .
V ehicle (cont.) Remote Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 Running While Parked . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-40 Symbols . . . . . . . . . . . . . . . . . . . . . . . . . .
An important point after buying a device Chevrolet 2010 HHR (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Chevrolet 2010 HHR yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Chevrolet 2010 HHR - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Chevrolet 2010 HHR you will learn all the available features of the product, as well as information on its operation. The information that you get Chevrolet 2010 HHR will certainly help you make a decision on the purchase.
If you already are a holder of Chevrolet 2010 HHR, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Chevrolet 2010 HHR.
However, one of the most important roles played by the user manual is to help in solving problems with Chevrolet 2010 HHR. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Chevrolet 2010 HHR along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
