Instruction/ maintenance manual of the product 2010 Corvette Convertible Chevrolet
Go to page of 472
2010 Chevrolet Corvette Owner Manual M In Brief ................ .......... ........... ....... 1 - 1 I n s t r u m e n t P a n e l ... .............................. 1 - 2 Initial Drive Information . . . . . . . . . . . . . . . . . . . . . . . . . . .
2010 Chevrolet Corvette Owner Manual M Service and Appearance Care . . . . . . . . . . . . . . . . . . . 6-1 S e r v i c e .................................... ....... 6 - 3 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GENERAL MOTORS, GM, the GM Emblem, CHEVROLET , the CHEVROLET Emblem, the names CORVETTE, Z06, ZR1, CORV ETTE GRAND SPORT and the CORVETTE Emblem are registered trademarks of General Motors. This manual describes features that may or may not be on your specific vehicle either because they are options that you did not purchase or due to changes subsequent to the printing of this owner manual.
Safety W arnings and Symbols W arning messages found on vehicle labels and in this manual describe hazards and what to do to avoid or reduce them. Danger indicates a hazard with a high level of risk which will result in serious injury or death. W arning or Caution indicates a hazard that could result in injury or death.
V ehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index. 9 : Airbag Readiness Light # : Air Conditioning ! : Antilock Brake System (ABS) g : Audio Steering Wheel Controls or OnStar ® $ : Brake System Warning Light " : Charging System I : Cruise Control B : Engine Coolant T emperature O : Exterior Lamps # : Fog Lamps .
2 NOTES vi.
Section 1 In Brief Instrument Panel ................................... 1-2 Initial Drive Information .. ....... .................. 1-4 Remote Keyless Entry (RKE) System . . . . . . . . . . . 1-4 Door Locks . . . . . . . . . . . . . . . . . . . . . . .
Instrument Panel 1-2.
A. Outlet Adjustment on page 4 ‑ 27 . B. Head-Up Display (HUD) on page 4 ‑ 16 (If Equipped). C. T urn Signal/Multifunction Lever on page 4 ‑ 4 . Cruise Control on page 4 ‑ 7 . Fog Lamps on page 4 ‑ 13 . Exterior Lamps on page 4 ‑ 1 1 . D. Manual Shift Paddles (If Equipped).
Initial Drive Information This section provides a brief overview about some of the important features that may or may not be on your specific vehicle. For more detailed information, refer to each of the features which can be found later in this owner manual.
Door Locks From the outside, press the Q or K button on the keyless access transmitter . When you have the transmitter with you, you may also unlock and open the door by squeezing the door handle sensor (A). From the inside, use the power door lock switch (B), located at the top of the door panel, near both windows.
T runk Release Opening and Closing the Hatch/T runk There are three ways to open the hatch/trunk: . T ouch the button located above the license plate. The Keyless Access transmitter must be within three feet of the button. . Press the V button located to the left of the steering wheel.
Seat Adjustment Manual Seats 1. Lift the bar to unlock the seat. 2. Slide the seat to the desired position and release the bar . T ry to move the seat to be sure it is locked in place. See Manual Seats on page 2 ‑ 2 . Power Seats On vehicles with power seats, the control is located on the outboard side of the seat.
Power Lumbar and Side Bolsters On vehicles with power lumbar and side bolsters: . Move (A) forward or rearward to adjust lumbar support. . Move (B) up or down to adjust the side bolsters. See Power Lumbar and Side Bolsters on page 2 ‑ 3 . Reclining Seatbacks T o recline the seatback: 1.
Heated Seats On vehicles with heated seats, the buttons are located on the center console. The ignition must be on for this feature to work. L : Press to turn the seat on at the high setting. Press again to turn it to the low setting 9 : Press to turn the system off.
Sensing System for Passenger Airbag The passenger sensing system will turn off the right front passenger frontal airbag and seat ‐ mounted side impact airbag under certain conditions. The driver airbags are not affected by this. The passenger airbag status indicator will be visible in the rearview mirror when the vehicle is started.
Mirror Adjustment Exterior Mirrors Controls for the outside power mirrors are located on the driver door . 1. Move the top control to the left or right to select either the driver or passenger mirror . 2. Use the arrows located on the four-way control pad to move the mirror in the desired direction.
Steering Wheel Adjustment The lever is located on the left side of the steering column. T o adjust the steering wheel: 1. Pull the lever toward you. 2. Move the steering wheel up or down into a comfortable position. 3. Release the lever to lock the steering wheel in place.
Interior Lighting Courtesy Lamps When any door or the hatch/trunk lid is opened, the interior lamps will go on, unless it is bright outside. The courtesy lamps can also be turned on and off by pressing the instrument panel brightness knob. Reading Lamps The inside rearview mirror includes two reading lamps.
; : Manual operation of the parking lamps and other exterior lamps. 5 : Manual operation of the headlamps and other exterior lamps. T urn and Lane-Change Signal The turn signal lever has two upward and downward positions to signal a lane change or a turn.
Climate Controls With this system, the heating, cooling, and ventilation can be controlled. A. Driver T emperature Control B. Display C. Passenger T emperature Control D. AUTO E. Air Recirculation F . Air Conditioning G. Fan Control H. Air Delivery Mode Control I.
The Manual Paddle Shift system can be deactivated by moving the shifter from S (Sport Mode) back to D (Drive), or by holding the up ‐ shift button for more than one second. The Manual Paddle Shift system will not allow either an up-shift or a down-shift, if the vehicle speed is too fast or too slow , nor will it allow a start from 4 (Fourth) or higher gear See Automatic T ransmission Operation on page 3 ‑ 26 .
O e : T urn to select radio stations. t SEEK u : Press to seek stations. t SCAN u : Press and hold to scan stations. 4 : Press to change the information that shows on the display while listening to the radio. For more information about these and other radio features, see Audio System(s) on page 4 ‑ 80 and Radio(s) on page 4 ‑ 81 .
Portable Audio Devices This vehicle may have an auxiliary input jack, located on the audio faceplate. External devices such as iPod ® , MP3 players, etc. can be connected to the auxiliary input jack using a 3.5 mm (1/8 in) input jack cable. See “ Using the Auxiliary Input Jack ” under Radio(s) on page 4 ‑ 81 .
Navigation System The vehicle's navigation system provides detailed maps of most major freeways and roads throughout the United States and Canada. After a destination has been set, the system provides turn-by-turn instructions for reaching the destination.
TRIP : Press to display your total and trip distance driven, the elapsed time function, your average speed, and the engine oil life. OPTION : Press to choose personal options that are available on your vehicle, depending on the options your vehicle is equipped with, such as door locks, easy entry seats, and language.
Power Outlets The accessory power outlet can be used to connect electrical equipment, such as a cellular phone. The accessory power outlet is located inside the center console storage compartment, on the forward left side. T o use the outlet, remove the tethered cap.
The vehicle may have Competitive Driving Mode (except ZR1), Performance T raction Management (ZR1), and Launch Control systems designed to allow increased performance while accelerating and cornering. See Competitive Driving Mode on page 5 ‑ 9 . T owing The vehicle was neither designed nor intended to be towed with any of its wheels on the ground.
Z06, Z16, and ZR1 Features Checking Engine Oil ZO6, Z16 (Grand Sport), and ZR1 models have a high performance dry sump lubrication system. This system operates differently than a standard engine lubrication system. See Engine Oil on page 6 ‑ 19 . Y ou should check the oil level only after the engine has been thoroughly warmed up and then shut off for at least five minutes.
Engine Oil Life System The engine oil life system calculates engine oil life based on vehicle use and displays a DIC message when it is necessary to change the engine oil and filter . The oil life system should be reset to 100% only following an oil change.
Roadside Assistance Program U.S.: 1-800-CHEV -USA (1-800-243-8872) TTY Users: 1-888-889-2438 Canada: 1-800-268-6800 As the owner of a new Chevrolet, you are automatically enrolled in the Roadside Assistance program. This program provides technically trained advisors who are available 24 hours a day , 365 days a year , minor repair information or towing arrangements.
How OnStar Service Works Q : This blue button connects you to a specially trained OnStar advisor to verify your account information and to answer questions. ] : Push this red emergency button to get priority help from specially trained OnStar emergency advisors.
Location information about the vehicle is only available if the GPS satellite signals are unobstructed and available. The vehicle must have a working electrical system, including adequate battery power , for the OnStar equipment to operate. There are other problems OnStar cannot control that may prevent OnStar from providing OnStar service at any particular time or place.
2 NOTES 1-28.
Section 2 Seats and Restraint System Front Seats ......................................... 2-2 Manual Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Power Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front Seats Manual Seats { W ARNING: Y ou can lose control of the vehicle if you try to adjust a manual driver's seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Power Seats On vehicles with power seats: . Move the control forward or rearward to adjust the seat location. . Move the front or rear of the control up or down to adjust the seat cushion height. Y our seat position can be stored and recalled if you have the memory option.
Heated Seats On vehicles with heated seats, the buttons are located on the center console. The ignition must be on for this feature to work. L : Press to turn the seat on at the high setting. Press again to turn it to the low setting 9 : Press to turn the system off.
T o recall a memory position: . On vehicles with an automatic transmission, press and release the desired button. If the vehicle is in P (Park), a single beep sounds and the memory position is recalled after a brief delay . If the vehicle is not in P (Park), three beeps sound and the memory position is not recalled.
Reclining Seatbacks { W ARNING: Y ou can lose control of the vehicle if you try to adjust a manual driver's seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to. Adjust the driver's seat only when the vehicle is not moving.
{ W ARNING: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job. In a crash, you could go into it, receiving neck or other injuries.
Seatback Latches T o fold a seatback forward, lift the latch located on top of the backside of the seat. The seatback locks when folded down. T o return the seatback upright, lift up on the latch and push the seatback rearward. The seatback must be locked in place.
Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly . It also describes some things not to do with safety belts. { W ARNING: Do not let anyone ride where a safety belt cannot be worn properly .
In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: Y ou never know if you will be in a crash. If you do have a crash, you do not know if it will be a serious one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive.
Put someone on it. Get it up to speed. Then stop the vehicle. The rider does not stop. 2-1 1.
The person keeps going until stopped by something. In a real vehicle, it could be the windshield... or the instrument panel... 2-12.
or the safety belts! With safety belts, you slow down as the vehicle does. Y ou get more time to stop. Y ou stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense. Questions and Answers About Safety Belts Q: Will I be trapped in the vehicle after a crash if I am wearing a safety belt? A: Y ou could be — whether you are wearing a safety belt or not.
Q: If I am a good driver , and I never drive far from home, why should I wear safety belts? A: Y ou may be an excellent driver, but if you are in a crash — even one that is not your fault — you and your passenger(s) can be hurt. Being a good driver does not protect you from things beyond your control, such as bad drivers.
Sit up straight and always keep your feet on the floor in front of you. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones and you would be less likely to slide under the lap belt.
Q: What is wrong with this? A: The shoulder belt is too loose. It will not give as much protection this way . { W ARNING: Y ou can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury .
Q: What is wrong with this? A: The lap belt is too loose. It will not give nearly as much protection this way . { W ARNING: Y ou can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Q: What is wrong with this? A: The belt is buckled in the wrong buckle. { W ARNING: Y ou can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Q: What is wrong with this? A: The belt is over an armrest. { W ARNING: Y ou can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Q: What is wrong with this? A: The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. { W ARNING: Y ou can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury .
Q: What is wrong with this? A: The belt is behind the body . { W ARNING: Y ou can be seriously injured by not wearing the lap-shoulder belt properly . In a crash, you would not be restrained by the shoulder belt. Y our body could move too far forward increasing the chance of head and neck injury .
Q: What is wrong with this? A: The belt is twisted across the body . { W ARNING: Y ou can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly , or ask your dealer/retailer to fix it.
Lap-Shoulder Belt All seating positions in the vehicle have a lap-shoulder belt. The following instructions explain how to wear a lap-shoulder belt properly . 1. Adjust the seat, if the seat is adjustable, so you can sit up straight. T o see how , see “ Seats ” in the Index.
4. T o make the lap part tight, pull up on the shoulder belt. It may be necessary to pull stitching on the safety belt through the latch plate to fully tighten the lap belt on smaller occupants. T o unlatch the belt, push the button on the buckle. The belt should return to its stowed position.
Safety Belt Pretensioners This vehicle has safety belt pretensioners for the front outboard occupants. Although the safety belt pretensioners cannot be seen, they are part of the safety belt assembly . They can help tighten the safety belts during the early stages of a moderate to severe frontal and near frontal crash if the threshold conditions for pretensioner activation are met.
Safety Belt Extender If the vehicle's safety belt will fasten around you, you should use it. But if a safety belt is not long enough, your dealer/ retailer will order you an extender . When you go in to order it, take the heaviest coat you will wear , so the extender will be long enough for you.
The manufacturer's instructions that come with the booster seat, state the weight and height limitations for that booster . Use a booster seat with a lap-shoulder belt until the child passes the below fit test: . Sit all the way back on the seat.
{ W ARNING: Never do this. Never allow two children to wear the same safety belt. The safety belt can not properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A safety belt must be used by only one person at a time.
Infants and Y oung Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
{ W ARNING: Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 40 km/h (25 mph), a 5.5 kg (12 lb) infant will suddenly become a 1 10 kg (240 lb) force on a person's arms.
{ W ARNING: Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat.
Q: What are the different types of add-on child restraints? A: Add-on child restraints, which are purchased by the vehicle's owner , are available in four basic types. Selection of a particular restraint should take into consideration not only the child's weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
{ W ARNING: A young child's hip bones are still so small that the vehicle's regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child's abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure.
A booster seat (C-D) is a child restraint designed to improve the fit of the vehicle's safety belt system. A booster seat can also help a child to see out the window . Securing an Add-On Child Restraint in the V ehicle { W ARNING: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the vehicle.
When securing an add-on child restraint, refer to the instructions that come with the restraint which may be on the restraint itself or in a booklet, or both, and to this manual. The child restraint instructions are important, so if they are not available, obtain a replacement copy from the manufacturer .
Y our vehicle does not have lower anchors or top tether anchors to secure a child restraint with the LA TCH system. If a national or local law requires that your top tether be anchored, do not use a child restraint in this vehicle because a top tether cannot be properly anchored.
A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle. The top tether attachment (B) on the child restraint connects to the top tether anchor in the vehicle in order to reduce the forward movement and rotation of the child restraint during driving or in a crash.
T op T ether Anchor Locations i (T op T ether Anchor): Seating positions with top tether anchors. T o assist you in locating the top tether anchors, the top tether anchor symbol is located on the trim cover . The top tether anchor is located behind the passenger seat.
Securing a Child Restraint with a T op T ether { W ARNING: If a LA TCH-type child restraint is not attached to anchors, the child restraint will not be able to protect the child correctly . In a crash, the child could be seriously injured or killed. Install a LA TCH-type child restraint properly using the anchors, or use the vehicle's safety belts to secure the restraint, following the instructions that came with the child restraint and the instructions in this manual.
If the position you are using has a fixed headrest or head restraint and you are using a dual tether , route the tether around the headrest or head restraint. 3. Push and pull the child restraint in different directions to be sure it is secure. Securing a Child Restraint in the Right Front Seat Position This vehicle has airbags.
Rear-facing child restraints should not be installed in the vehicle, even if the airbag(s) are of f. If the child restraint has the LA TCH system, see Lower Anchors and T ethers for Children (LA TCH) (Coupe and Convertible Models Only) on page 2 ‑ 35 or Lower Anchors and T ethers for Children (LA TCH) (Z06 and ZR1 Models Only) on page 2 ‑ 36 for how and where to install the child restraint using LA TCH.
4. Push the latch plate into the buckle until it clicks. Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary . 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock.
6. T o tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor . When installing a forward-facing child restraint, you may find it helpful to use your knee to push down on the child restraint as you tighten the belt.
Airbag System The vehicle has the following airbags: . A frontal airbag for the driver . . A frontal airbag for the right front passenger . . A seat-mounted side impact airbag for the driver . . A seat-mounted side impact airbag for the right front passenger .
{ W ARNING: Airbags inflate with great force, faster than the blink of an eye. Anyone who is up against, or very close to, any airbag when it inflates can be seriously injured or killed. Do not sit unnecessarily close to the airbag, as you would be if you were sitting on the edge of your seat or leaning forward.
Where Are the Airbags? The driver frontal airbag is in the middle of the steering wheel. The right front passenger frontal airbag is in the instrument panel on the passenger's side.
Driver Side shown, Passenger Side similar The seat-mounted side impact airbags for the driver and right front passenger are in the side of the seatbacks closest to the door . { W ARNING: If something is between an occupant and an airbag, the airbag might not inflate properly or it might force the object into that person causing severe injury or even death.
When Should an Airbag Inflate? Frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver's or right front passenger's head and chest. However , they are only designed to inflate if the impact exceeds a predetermined deployment threshold.
Thresholds can also vary with specific vehicle design. Frontal airbags are not intended to inflate during vehicle rollovers, rear impacts, or in many side impacts. In addition, your vehicle has dual-stage frontal airbags. Dual-stage airbags adjust the restraint according to crash severity .
What Makes an Airbag Inflate? In a deployment event, the sensing system sends an electrical signal triggering a release of gas from the inflator . Gas from the inflator fills the airbag causing the bag to break out of the cover and deploy . The inflator , the airbag, and related hardware are all part of the airbag module.
What Will Y ou See After an Airbag Inflates? After the frontal and seat-mounted side impact airbags inflate, they quickly deflate, so quickly that some people may not even realize the airbags inflated. Some components of the airbag module may be hot for several minutes.
airbags inflate. Y ou can lock the doors, turn the interior lamps off, and turn the hazard warning flashers off by using the controls for those features. { W ARNING: A crash severe enough to inflate the airbags may have also damaged important functions in the vehicle, such as the fuel system, brake and steering systems, etc.
Passenger Sensing System The vehicle has a passenger sensing system for the right front passenger position. The passenger airbag status indicator will be visible in the rearview mirror when the vehicle is started. United States Canada The words ON and OFF , or the symbol for on and off, will be visible during the system check.
A label on the sun visor says, “ Never put a rear-facing child seat in the front. ” This is because the risk to the rear-facing child is so great, if the airbag deploys. { W ARNING: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates.
When the passenger sensing system has turned off the right front passenger frontal airbag and seat-mounted side impact airbag, the off indicator will light and stay lit to remind you that the airbag(s) are off. See Passenger Airbag Status Indicator on page 4 ‑ 34 .
If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. T urn the vehicle off. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers.
If this happens, use the following steps to allow the system to detect that person and enable the right front passenger frontal airbag and seat-mounted side impact airbag: 1. T urn the vehicle off. 2. Remove any additional material from the seat, such as blankets, cushions, seat covers, seat heaters, or seat massagers.
A thick layer of additional material, such as a blanket or cushion, or aftermarket equipment such as seat covers, seat heaters, and seat massagers can affect how well the passenger sensing system operates. We recommend that you not use seat covers or other aftermarket equipment except when approved by GM for your specific vehicle.
Adding Equipment to Y our Airbag-Equipped V ehicle Q: Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? A: Y es. If you add things that change your vehicle's frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly .
Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check that the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly . Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job.
Replacing Restraint System Parts After a Crash { W ARNING: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. T o help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
2 NOTES 2-62.
Section 3 Features and Controls Keys ........................... ..................... 3-3 Keyless Access System . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Keyless Access System Operation . . . . . . . . . . . . . . 3-5 Doors and Locks ....
Section 3 Features and Controls Universal Home Remote System .. ............ .. 3-42 Universal Home Remote System Operation . . . . 3-43 Storage Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-50 G l o v e B o x ... ...
Keys { W ARNING: Leaving children in a vehicle with the keyless access transmitter is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move.
The key , located inside the keyless access transmitter , can be used to lock and unlock the glove box and to open the hatch/trunk lid if power to the vehicle is lost. See Hatch on page 3 ‑ 14 for more information. Press the button (A) near the bottom of the keyless access transmitter to remove the key .
Keyless Access System See Radio Frequency Statement on page 8 ‑ 20 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and RSS-210/21 1 of Industry Canada. Changes or modifications to this system by other than an authorized service facility could void authorization to use this equipment.
Keyless T runk Opening Press the hatch/trunk release button located on the rear of the hatch/trunk lid above the license plate to open the trunk if the keyless access transmitter is within range. See Hatch on page 3 ‑ 14 for additional information. There are other conditions that can affect the performance of the transmitter .
Programming T ransmitters to the V ehicle Only keyless access transmitters programmed to this vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer/retailer . The vehicle can be reprogrammed so that lost or stolen transmitters no longer work.
Programming without a Recognized T ransmitter This procedure requires three ten minutes cycles to complete the programming process. United States owners are permitted to program a new transmitter to their vehicle when a recognized transmitter is not available.
8. The DIC reads WAIT 10 MINUTES and counts down to zero. 9. The DIC displays OFF-ACCESSORY TO LEARN again. 10. Press Acc. on the ignition switch. 1 1. Steps 8, 9 and 10 will be repeated two more times. 12. A beep sounds and the DIC reads READY FOR FOB #1.
Battery Replacement Notice: When replacing the battery , do not touch any of the circuitry on the transmitter. Static from your body could damage the transmitter . 1. Separate the transmitter with a flat, thin object inserted into the slot on the side or back of the transmitter .
There are several ways to lock and unlock your vehicle. From the outside, press the lock or unlock button on the keyless access transmitter . Door Open to Show Location of Door Handle Sensor When you have the transmitter with you, you may also unlock and open the door by squeezing the door handle sensor (A).
2. From outside the vehicle, use the key in the cylinder above the license plate to open the hatch. Then, use the door release tab (A), located on the carpet inside the hatch on the driver's side of the vehicle. Pull the tab to unlock and unlatch the driver's door .
Automatic Door Lock The vehicle is programmed so that, when the doors are closed, the ignition is on and the shift lever is moved out of P (Park)for automatic transmissions, or when vehicle speed becomes faster than 8 mph (13 km/h) for manual transmissions, both doors will lock.
Hatch { W ARNING: Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
Hatch/T runk Lid Release There are several ways to release the hatch/trunk lid. If your vehicle has an automatic transmission, the shift lever must be in P (Park). For manual transmission vehicles, the parking brake must be set when the ignition is started for the hatch/trunk release to operate.
Emergency T runk Release Handle (Coupe) Notice: Do not use the emergency trunk release handle as a tie-down or anchor point when securing items in the trunk as it could damage the handle. The emergency trunk release handle is only intended to aid a person trapped in a latched trunk, enabling them to open the trunk from the inside.
Power Windows The power window switches are located on each door . Pull up or press down on the front of the switch to raise or lower the window . Retained Accessory Power (RAP) allows you to use the power windows when the ignition is off. For more information, see Retained Accessory Power (RAP) on page 3 ‑ 24 .
Express-Down Window Press the front of the switch to the second position to activate the express-down feature. If you want to stop the window as it is lowering, press the switch again. Window Indexing This feature automatically lowers the window a small amount when the door is opened.
Theft-Deterrent Systems V ehicle theft is big business, especially in some cities. This vehicle has theft-deterrent features, however, they do not make it impossible to steal. Theft-Deterrent System This vehicle has a theft-deterrent alarm system. The security light flashes if a door is open and locked with the power door lock switch.
T esting the Alarm T o test the system: 1. Make sure the trunk lid/hatch is latched. 2. Lower the window on the driver door . 3. Manually arm the system. 4. Close the doors and wait 30 seconds. 5. Reach through the open window and manually pull the release lever on the floor .
If the vehicle does not start and the keyless access transmitter appears to be undamaged, try another keyless access transmitter . Or , place the transmitter in the transmitter pocket. See “ NO FOBS DETECTED ” under DIC Warnings and Messages on page 4 ‑ 52 for additional information.
For the first 500 miles/805 km: . Avoid full throttle starts and abrupt stops. . Do not exceed 4,000 engine rpm. . Avoid driving at any one constant speed, fast or slow , including the use of cruise control. . Avoid downshifting to brake or slow the vehicle when the engine speed will exceed 4000 RPM.
Ignition Positions The vehicle has an electronic keyless ignition with a pushbutton start. In order to shift out of P (Park), the vehicle must be running or in Acc. mode and the regular brake pedal must be applied. / (ST ART): Press this button while your foot is on the brake for an automatic transmission, or while pressing in the clutch for a manual transmission, to start the engine.
Retained Accessory Power (RAP) These vehicle accessories can be used for up to 10 minutes after the engine is turned off: . Audio System . Power Windows These features continue to work up to 10 minutes after the engine is turned off or until either door is opened.
3. Do not race the engine immediately after starting it. Operate the engine and transmission gently until the oil warms up and lubricates all moving parts. 4. If the engine does not start and no DIC message is displayed, wait 15 seconds before trying again to let the cranking motor cool down.
Stopping the Engine If the vehicle has an automatic transmission, move the shift lever to P (Park) and press and hold the Acc. (Off/Accessory) button, located on the instrument panel, until the engine shuts off. If the shift lever is not in P (Park), the engine shuts off and the vehicle goes into the Accessory Mode.
{ W ARNING: It is dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to. If you have left the engine running, the vehicle can move suddenly .
N (Neutral) : In this position, the engine does not connect with the wheels. T o restart the engine when the vehicle is already moving, use N (Neutral) only . If the vehicle needs towing, see T owing Your V ehicle on page 5 ‑ 33 . { W ARNING: Shifting into a drive gear while the engine is running at high speed is dangerous.
Manual Paddle Shift While in S (Sport Mode), the paddles located on the steering wheel can be used to manually up-shift or down-shift the transmission. The Manual Paddle Shift system is activated from S (Sport Mode) by pushing the paddle, above the steering wheel spokes, to up-shift to the next gear, or pulling on the paddle, behind the steering wheel spokes, to down-shift to the next gear .
When using the Manual Paddle Shift feature while in S (Sport Mode), the current gear will be displayed in the Driver Information (DIC), or the Head-Up Display (HUD), if the vehicle has either of these features. If the vehicle has a Navigation system, see “ Head-Up Display (HUD) ” in the Index of the navigation manual.
For vehicles with a 2.56:1 Axle Ratio (RPO GM8) . Up-shifts to 4 (Fourth) gear require approximately 35 km/h (22 mph). . Up-shifts to 5 (Fifth) gear require approximately 45 km/h (28 mph). . Up-shifts to 6 (Sixth) gear require approximately 65 km/h (41 mph).
Manual T ransmission Operation This is the shift pattern for the six-speed manual transmission. Here is how to operate the transmission: 1 (First) : Press the clutch pedal and shift into 1 (First). Then slowly let up on the clutch pedal as you press the accelerator pedal.
Shift Speeds (Manual T ransmission) { W ARNING: If you skip a gear when you downshift, you could lose control of the vehicle. Y ou could injure yourself or others. Do not shift down more than one gear at a time when you downshift. This chart shows when to shift to the next higher gear for the best fuel economy .
Downshifting (Manual T ransmission) Do not downshift into the gear shown below at a speed greater than shown in the table: 1 (First) 50 mph (80 km/h) 2 (Second) 74 mph (1 19 km/h) 3 (Third) 101 mph (163 km/h) 4 (Fourth) 130 mph (209 km/h) Notice: If you skip more than one gear when you downshift, or if you race the engine when you release the clutch pedal while downshifting, you could damage the engine, clutch, driveshaft or the transmission.
Shifting Into Park (Automatic T ransmission) { W ARNING: It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly .
T orque Lock (Automatic T ransmission) If you are parking on a hill and you do not shift the transmission into P (Park) properly , the weight of the vehicle may put too much force on the parking pawl in the transmission. Y ou may find it difficult to pull the shift lever out of P (Park).
Parking Over Things That Burn { W ARNING: Things that can burn could touch hot exhaust parts under the vehicle and ignite. Do not park over papers, leaves, dry grass, or other things that can burn. Engine Exhaust { W ARNING: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
Running the V ehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know . { W ARNING: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Mirrors Automatic Dimming Rearview Mirror The vehicle may have an automatic dimming inside rearview mirror with a compass display and/or map lamps, and OnStar ® . The mirror automatically changes to reduce glare from headlamps behind you. A time delay feature prevents rapid changing from the day to night positions while driving under lights and through traffic.
Compass Calibration Press P once to turn the compass display on or off. If after several seconds the display does not show a compass heading, there may be a strong magnetic field interfering with the compass. Interference can be caused by a magnetic antenna mount, note pad holder or similar object.
Outside Power Mirrors Controls for the outside power mirrors are located on the driver door . T o adjust the mirrors: 1. Move the top selector control to the left or right to select either the driver or passenger mirror . 2. Use the arrows located on the four-way control pad to move the mirror in the desired direction.
Outside Convex Mirror { W ARNING: A convex mirror can make things, like other vehicles, look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on the right. Check the inside mirror or glance over your shoulder before changing lanes.
Universal Home Remote System Operation On vehicles with this feature there are three round Light Emitting Diode (LED) indicator lights above the Universal Home Remote buttons, follow the instructions below . This system provides a way to replace up to three remote control transmitters used to activate devices such as garage door openers, security systems, and home automation devices.
T o program up to three devices: 1. Press ST ART or put the vehicle in accessory mode. See Ignition Positions on page 3 ‑ 23 for additional information. Programming can only occur when the vehicle is running or in accessory mode. 2. From inside the vehicle, press the two outside buttons at the same time for one to two seconds, and immediately release them.
4. Immediately return to the vehicle. Press and hold the Universal Home Remote button that will be used to control the garage door until the garage door moves. The indicator light, above the selected button, should slowly blink. This button may need to be held for up to 20 seconds.
2. T o verify that the garage door opener is a Fixed Code unit, remove the battery cover on the hand held transmitter supplied by the manufacturer of the garage door opener motor . If there are a row of dip switches similar to the graphic above, the garage door opener is a Fixed Code unit.
Example of Eight Dip Switches with Three Positions The panel of switches might not appear exactly as they do in the examples above, but they should be similar . The switch positions on the hand-held transmitter could be labeled, as follows: . A switch in the up position could be labeled as “ Up, ” “ +, ” or “ On.
5. The indicator lights blink slowly . Enter each switch setting from Step 3 into the vehicle's Universal Home Remote. Y ou have two and one-half minutes to complete Step 5. Now press one button on the Universal Home Remote for each switch setting as follows: .
Using Universal Home Remote Press and hold the appropriate button for at least half of a second. The indicator light comes on while the signal is being transmitted. Operation can occur: . If the vehicle is in accessory mode. . If the vehicle is in running.
Storage Areas Glove Box Open the glove box by lifting up on the lever . Use the key to lock and unlock the lighted glove box. Cupholders T wo cupholders are located on the center console next to the shift lever . Slide the handle from the left to the right side to access the lid.
Rear Storage Area T wo rear storage compartments are located in the floor of the rear hatch/trunk area. Convertible shown, Coupe similar T o access a storage compartment, pull up to open the cover . The covers cannot be removed. For Z06, ZR1 and Grand Sport models, the right rear compartment stores the battery and cannot be used for storage.
Pull the divider up and snap it onto the snaps on both sides of the trunk. Convenience Net Use the convenience net, located in the rear , to store small loads as far forward as possible. The net should not be used to store heavy loads. Cargo Cover For vehicles with this feature, the security shade can provide hidden storage in the rear area of the vehicle.
3. Grasp the loop at the rear center of the shade and wrap it around the striker assembly . 4. Push the loop to the top of the striker (base plate). 3-53.
Roof Panel On vehicles with a removable roof panel, follow the procedures when removing or installing it. Removing the Roof Panel { W ARNING: Do not try to remove a roof panel while the vehicle is moving. T rying to remove the roof panel while the vehicle is moving could cause an accident.
6. T o unlock the release latches on the front of the roof panel, grasp each handle and pull it outward. The driver's side handle moves toward the driver's door .
7. T o unlock the rear of the roof panel's rear release latch, press the back of the release handle (B). Then press the button on the front of the release handle (A). Pull down the latch lever . 8. Stand on one side of the vehicle, and if necessary , have someone stand on the other side.
Notice: If you drop or rest a roof panel on its edges, the roof panel, paint and/or weatherstripping may be damaged. Always place the roof panel in the stowage receivers after removing it from the vehicle. 1. T urn the roof panel so that the front edge of the panel is facing the storage area.
Installing the Roof Panel { W ARNING: An improperly attached roof panel may fall into or fly off the vehicle. Y ou or others could be injured. After installing the roof panel, always check that it is firmly attached by pushing up on the underside of the panel.
6. T urn the front release handles inward so that they latch to the closed position. 7. Push up on the handle of the rear roof release handle to latch its hook in the closed position. 8. Push and pull the roof panel up and down and side-to-side to ensure the roof panel is securely installed.
The parts of the manual convertible top that are used when lowering and raising it are: A. Front Edge of the Convertible T op B. Rear Edge of the Convertible T op C. T onneau Cover Notice: Leaving the convertible top down and exposing the interior of your vehicle to outdoor conditions may cause damage.
Lowering the Manual Convertible T op 1. Park on a level surface. Shift an automatic transmission into P (Park) and set the parking brake. Shift a manual transmission into N (Neutral) and set the parking brake. 2. Make sure the ignition is off. 3. Make sure the trunk is closed.
6. T ilt the driver's seatback forward and press the tonneau cover release button located on the underside of the tonneau cover (C) behind the driver's seat. Then raise the tonneau cover (C). If the tonneau cover does not release and three chimes are heard, check to make sure the trunk lid is closed.
7. Pull the cable to release the tonneau cover . 8. Push forward on the front edge (A) of the convertible top to allow the rear edge (B) of the convertible top to be moved to its full-down position.
9. Then move the top rearward to its fully-stored position. 10. After the top is stored, apply one even push on the center of the front edge (A) of the convertible top to assure that the top is fully retracted. 1 1. Close the tonneau cover (B) by pressing down on it with a swift, firm motion.
6. Pull the convertible top up by firmly gripping the front edge (A) near the center and applying a brisk upward and forward motion to get the top in the full-up position. 7. Lift the rear edge (B) of the convertible top to its full-up position by first raising the front edge (A).
1 1. Pull the top front latch handle down and turn it counterclockwise to lock the convertible top. Convertible T op (Power) For care and cleaning of the convertible top see Convertible T op on page 6 ‑ 97 under “ Service and Appearance Care ” .
Notice: Lowering the top if it is damp, wet, or dirty can cause stains, mildew , and damage to the inside of your vehicle. Dry off the top before lowering it. Notice: If you lower the top on your vehicle in cold weather (0°F/-18°C or lower), you may damage top components.
4. Push and hold the bottom of the power convertible top button, located to the left of the steering wheel, on the instrument panel. The windows will automatically lower and the convertible top will lower into the rear of the vehicle. A chime will sound when the convertible top has lowered completely .
If the radio is on the sound may be muted for a brief time due to a new audio system equalization being loaded. If the vehicle has lost power , the convertible top can still be raised by releasing pressure on the hydraulic pump, located under the passenger's side of the tonneau cover , by using the following steps.
1. Open the tonneau cover by pulling the emergency release cable. The tonneau cover emergency release cable is located behind the passenger's seat head restraint, on the underside forward edge of the tonneau cover . Also, see Hatch on page 3 ‑ 14 for information on the emergency trunk release handle.
3. Use the wrench, located in the console, and turn the pressure release bolt counterclockwise one revolution, to relieve pressure to the hydraulic pump. This will allow you to manually raise the convertible top. 4. Then follow the steps under raising the manual convertible top.
2 NOTES 3-72.
Section 4 Instrument Panel Instrument Panel Overview ................... ..... 4-3 Hazard W arning Flashers . . . . . . . . . . . . . . . . . . . . . . . 4-3 Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 T ilt Wheel .
Section 4 Instrument Panel F o g L a m p L i g h t ........................... ..... 4 - 4 5 Lights On Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-45 Highbeam On Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-45 F u e l G a u g e .
Instrument Panel Overview Hazard W arning Flashers The hazard warning flashers warns others that you have a problem. The button is located near the center of the instrument panel. | : Press to make the front and rear turn signal lamps flash on and off.
T elescopic Steering Column For vehicles with this feature, the telescopic steering column switch is located on the right side of the steering column. T o adjust the telescopic steering column: 1. Push the switch forward to move the wheel away from you.
T urn and Lane-Change Signals (Auto Signal) An arrow on the instrument panel cluster flashes in the direction of the turn or lane change. Move the the lever all the way up or down to signal a turn. Raise or lower the lever until the arrow starts to flash to signal a lane change.
Windshield Wipers The windshield wiper lever is located on the right side of the steering column. Move the lever to the following positions: 1 (High Speed) : Fast wipes. 6 (Low Speed) : Slow wipes. & (Delay) : Use to set a delay between wipes. x (Delay Adjustment) : Use for a delayed wiping cycle.
{ W ARNING: In freezing weather , do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision. If the fluid in the windshield washer fluid reservoir is low , the message CHECK WASHER FLUID will appear on the Driver Information Center (DIC) display .
The vehicle has cruise control. 9 (Off): T urns the system off. R (On): T urns the system on. + (Resume/Accelerate): Use to make the vehicle accelerate or resume a previously set speed. T (Set): Press this button at the end of the lever to set the speed.
Resuming a Set Speed If the cruise control is set at a desired speed and then the brakes are applied, the cruise control is disengaged. But it does not need to be reset. Once the vehicle is going about 40 km/h (25 mph) or more, you can move the cruise control switch briefly from R to S .
Using Cruise Control on Hills How well the cruise control works on hills depends upon the vehicle's speed, load, and the steepness of the hills. When going up steep hills, you might want to step on the accelerator pedal to maintain the vehicle's speed.
Exterior Lamps The exterior lamp control is located to the left of the steering wheel on the multifunction lever . O (Exterior Lamp Control) : Turn the band with this symbol on it to operate the exterior lamps. The exterior lamp band has four positions: O (Off) : Turns of f all lamps.
Wiper Activated Headlamps This feature activates the headlamps and parking lamps after the windshield wipers have been in use for approximately 15 seconds and deactivates and returns to ambient lighting conditions 15 seconds after the wipers are turned off.
When it is bright enough outside, the regular lamps go off, and the front turn signal lamps will take over . If the vehicle is started in a dark garage, the automatic headlamp system comes on immediately . Once the vehicle leaves the garage, it takes approximately one minute for the automatic headlamp system to change to DRL if it is light outside.
T wilight Sentinel ® T wilight Sentinel ® can turn the lamps on and off for you. A light sensor on top of the instrument panel makes the T wilight Sentinel ® work, so be sure it is not covered. With T wilight Sentinel ® , the following will happen: .
Exterior Lighting Battery Saver If the manual parking lamps or headlamps have been left on, the exterior lamps will turn off as soon as the ignition is turned off or Retained Accessory Power (RAP) is active. This protects against draining the battery in case you have accidentally left the headlamps or parking lamps on.
Battery Run-Down Protection This vehicle has a feature to help prevent the battery from being drained in case any of the following lamps are left on; the underhood lamp, if your vehicle has this feature, vanity mirror lamps, cargo lamps, reading lamps, console or glove box lamps.
. T ransmission Fluid T emperature Gauge, (Automatic T ransmission V ehicles Only) . Engine Oil T emperature Gauge . Engine Oil Pressure Gauge . G-Force Gauge . Boost Gauge (If Equipped) . Audio Functions, Street Mode Only . Navigation, Only with Navigation Radio, T urn-by-Turn Guidance There are three HUD modes that can be viewed in the HUD display .
Within each mode, the display , can be further customized by pressing the P AGE button. Pressing this button in each mode will turn off and on the following: . Street Mode — No tachometer , circular tachometer , and linear tachometer . . T rack Modes 1 and 2 — No minor gauge, coolant temperature, transmission oil temperature, engine oil temperature, engine oil pressure, and boost gauge.
The HUD controls are located to the left of the steering wheel. T o adjust the HUD so it can be seen properly , do the following: 1. Start the engine and press the HUD dimmer control all the way up by pressing the (+) button. The brightness of the HUD image is determined by the light conditions in the direction the vehicle is facing and where you have the HUD dimmer control set.
T o change the language and unit selections, see “ OPTION ” under DIC Operation and Displays on page 4 ‑ 47 . Clean the inside of the windshield as needed to remove any dirt or film that reduces the sharpness or clarity of the HUD image. T o clean the HUD, spray household glass cleaner on a soft, clean cloth.
Notice: Adding any electrical equipment to the vehicle can damage it or keep other components from working as they should. The repairs would not be covered by the vehicle warranty . Do not use equipment exceeding maximum amperage rating of 20 amperes.
Climate Controls Dual Automatic Climate Control System With this system the heating, cooling, and ventilation can be controlled. A. Driver T emperature Controls B. Display C. Passenger T emperature Control D. AUTO E. Recirculation F . Air Conditioning G.
The system operates to reach the set temperature as quickly as possible. The AUTO control system works best with the windows up and the removable roof installed or the convertible top up. 1. Press the AUTO button. 2. Adjust the temperature to a comfortable setting between 16°C (60°F) and 32°C (90°F).
N (Air Delivery Mode Control) : Press this button to manually lock in the current air delivery setting and to stop the automatic mode control. Pressing N deletes AUTO from the digital display and the mode graphics will be shown. T o change the setting, press N again.
Y ou may notice a slight change in engine performance when the air-conditioning compressor shuts off and turns on again. This is normal. The system is designed to make adjustments to help with fuel economy while still maintaining the selected temperature.
Sensors The solar sensor on the vehicle monitors the solar heat and uses the information to maintain the selected temperature when operating in AUTO mode by automatically adjusting the temperature, fan speed and air delivery system. The system may also supply cooler air to the side of the vehicle facing the sun.
The rear window defogger turns off about 10 minutes after the button is pressed when traveling less than 48 km/h (30 mph). If turned on again, the defogger only runs for about five minutes before turning off. The defogger can also be turned off by turning of f the engine.
Passenger Compartment Air Filter The passenger compartment air filter removes certain particles from the air including pollen and dust particles. Reductions in airflow , which may occur more often in dusty areas, indicate that the filter may need to be replaced.
3. Remove the filter and install the new air filter . 4. Replace the filter cover . 5. Attach the retainer clips. W arning Lights, Gauges, and Indicators W arning lights and gauges can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Instrument Panel Cluster United States Manual T ransmission shown, Canada, Automatic T ransmission and Z06 Model similar 4-30.
ZR1 – United States shown Canada similar 4-31.
Speedometer and Odometer The speedometer shows the speed in either kilometers per hour (km/h) or miles per hour (mph). For more information see “ Personal Options ” under DIC Vehicle Personalization on page 4 ‑ 71 . T o read the odometer with the ignition off, turn on the parking lamps.
Airbag Readiness Light The system checks the airbag's electrical system for possible malfunctions. If the light stays on it indicates there is an electrical problem. The system check includes the airbag sensor , the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module.
Passenger Airbag Status Indicator The vehicle has the passenger sensing system. See Passenger Sensing System on page 2 ‑ 53 for important safety information. The rearview mirror has a passenger airbag status indicator . United States Canada When the vehicle is started, the passenger airbag status indicator will light ON and OFF , or the symbol for on and off, for several seconds as a system check.
If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system. See your dealer/retailer for service. { W ARNING: If the airbag readiness light ever comes on and stays on, it means that something may be wrong with the airbag system.
One-to-Four Shift Light (Manual T ransmission) When this light comes on, the vehicle can only be shifted from 1 (First) to 4 (Fourth) instead of 1 (First) to 2 (Second). The shift must be completed into 4 (Fourth) to turn off this feature. This helps the vehicle get the best possible fuel economy .
This light comes on briefly while starting the engine. If it does not come on, have it fixed so it is ready to warn if there is a problem. { W ARNING: The brake system might not be working properly if the brake system warning light is on. Driving with the brake system warning light on can lead to a crash.
T raction Control System (TCS) W arning Light The T raction Control System (TCS) W arning light comes on briefly when the engine is started. If the light does not, have the vehicle serviced by your dealer/retailer . If the system is working normally the light then goes off.
Active Handling System Light The Active Handling System light comes on briefly as the engine is started. If the light does not, have the vehicle serviced by your dealer/ retailer . If the system is working normally the light goes off. If the light stays on or comes on while driving, a chime sounds and a SERVICE ACTIVE HANDLING SYSTEM message appears on the DIC and the vehicle need service.
Engine Coolant T emperature Gauge United States Canada This gauge shows the engine coolant temperature. If the gauge pointer moves into the shaded area, the engine is too hot. This means that the engine coolant has overheated. If the vehicle has been operating under normal driving conditions, pull off the road, stop the vehicle and turn off the engine as soon as possible.
When the Light Flashes First and Then is On Steady This indicates that there may be a problem with the Tire Pressure Monitor System. The light flashes for about a minute and stays on steady for the remainder of the ignition cycle. This sequence repeats with every ignition cycle.
This light comes on during a malfunction in one of two ways: Light Flashing : A misfire condition has been detected. A misfire increases vehicle emissions and could damage the emission control system on the vehicle. Diagnosis and service might be required.
If none of the above have made the light turn off, your dealer/retailer can check the vehicle. The dealer/retailer has the proper test equipment and diagnostic tools to fix any mechanical or electrical problems that might have developed. Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or might begin programs to inspect the emission control equipment on the vehicle.
Engine Oil Pressure Gauge United States Canada United States — Z06 and ZR1 Models Canada — Z06 and ZR1 Models { W ARNING: Do not keep driving if the oil pressure is low . The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced.
The engine oil pressure can also be displayed using the GAGES button on the Driver Information Center (DIC). See Driver Information Center (DIC) on page 4 ‑ 47 . Security Light For information regarding this light and the vehicle's security system, see Theft-Deterrent System on page 3 ‑ 19 .
Fuel Gauge The fuel gauge shows how much fuel the vehicle has left while the engine is on. An arrow on the fuel gauge indicates the side of the vehicle the fuel door is on. When the needle approaches the low fuel symbol, a chime sounds and LOW FUEL appears on the Driver Information Center (DIC) display .
Boost Gauge (ZR1 Only) United States Canada For vehicles that have this gauge, it is located near the driver side of the instrument panel cluster . This gauge indicates vacuum during light to moderate throttle and boost under heavier throttle. It displays the air pressure level in the intake manifold before it enters the engine's combustion chamber .
. 4 (Fuel): Press this button to display fuel information such as fuel economy and range. 2 (Gauges): Press this button to display gauge information like oil pressure and temperature, coolant temperature, automatic transmission fluid temperature, if equipped, battery voltage, and front/rear tire pressures.
Press the fuel button to display average fuel economy , such as: . A VERAGE FUEL ECONOMY 1 1.7 L/100 km or . A VERAGE FUEL ECONOMY 20.1 MPG Instantaneous Fuel Economy : Instantaneous fuel economy reflects only the fuel economy that the vehicle has right now and will change frequently as driving conditions change.
If the oil temperature is low , the display will show OIL TEMPERA TURE LOW . If the oil temperature is high, the display will show OIL TEMPERA TURE HIGH. Coolant T emperature : This display shows the engine coolant temperature. Press the gauges button again to display the coolant temperature, such as: .
TRIP Button The TRIP button displays the odometer , trip distance, elapsed time, average speed, and oil life remaining information. Odometer : The odometer shows how far your vehicle has been driven in either kilometers or miles. Press the TRIP button to display odometer readings, such as: .
Press and hold the RESET button to reset to 0.0 km/h (mph). Engine Oil Life : Press the TRIP button until the engine oil life is displayed, such as OIL LIFE REMAINING 89%. This is an estimate of the engine oil's remaining useful life. It will show 100% when the system is reset after an oil change.
ABS (Antilock Brake System) ACTIVE This message displays when the Antilock Brake System (ABS) is adjusting brake pressure to help avoid a braking skid. Slippery road conditions may exist if this message is displayed, so adjust your driving accordingly .
BUCKLE P ASSENGER This message reminds you to buckle the passenger's safety belt. This message displays and a sound will be heard when the ignition is on, the driver's safety belt is buckled, the passenger's safety belt is unbuckled with the passenger airbag enabled, and the vehicle is in motion.
CHECK COOLANT LEVEL This message displays when the engine coolant level is low . Have the cooling system serviced by your dealer/ retailer as soon as possible. See Engine Coolant on page 6 ‑ 34 . CHECK GAS CAP This message displays if the fuel cap has not been fully tightened.
COOLANT OVER TEMPERA TURE This message displays and a sound will be heard if the engine coolant exceeds 124°C (255°F). If you have been operating the vehicle under normal driving conditions, pull off the road, stop the vehicle, and turn off the engine as soon as possible.
Multiple chimes sound when this message is displayed. This message remains displayed and active until the issue is resolved. HEADLAMPS SUGGESTED This message displays if it is dark enough outside and the headlamps and the T wilight Sentinel ® controls are off.
LOW OIL PRESSURE This message displays if low oil pressure levels occur . If this message appears while the engine is running, stop the engine and do not operate it until the cause of low oil pressure is corrected. Severe damage to the engine can result.
MAXIMUM SPEED 129 km/h (80 MPH) This message displays when a malfunction is present in the Selective Ride Control system. The vehicle speed will be limited to a value determined by the vehicle when the shock absorber system has failed and the shocks are in their full soft mode.
NO FOB - OFF OR RUN? This message displays when the keyless access transmitter is not detected inside the vehicle while you are trying to turn the ignition off. The vehicle may be near a strong radio antenna signal causing the keyless access system to be jammed.
This system is available only on ZR1 models. See “ Performance T raction Management ” and “ Launch Control ” under Competitive Driving Mode on page 5 ‑ 9 and Racing or Other Competitive Driving on page 5 ‑ 19 for more information about the use of this mode.
PERF TRAC 5 – RACE ACTIVE HANDLING OFF This message displays and a sound will be heard when this Performance T raction Management mode is selected. The instrument panel cluster light will also be on when this mode is selected. Launch Control is available when this mode selected.
SERVICE ACTIVE HANDLING SYSTEM This message displays if there is a problem with the Active Handling System and the vehicle needs service. The active handling system light on the instrument panel cluster also turns on and a sound will be heard. See your dealer/retailer .
SERVICE CHARGING SYSTEM If this message displays while you are driving, there may be a problem with the electrical charging system. It could mean that there is a loose or broken drive belt or that there is another electrical problem. Have the vehicle checked right away by your dealer/retailer .
SERVICE TRACTION SYSTEM If this message displays when you are driving, there is a problem with the T raction Control System (TCS) and the vehicle is in need of service. See your dealer/retailer . When this message is displayed, the system will not limit wheel spin.
The vehicle will remain in ACCESSORY , without the 20 minute time-out period, until the shift lever is moved to P (Park) or until the driver presses the pushbutton to restart the vehicle. See Ignition Positions on page 3 ‑ 23 for more information. SHIFT TO P ARK OR SET P ARK BRAKE FOR TOP If the vehicle has an automatic transmission, this message displays and a sound will be heard if you try to operate the power convertible top without first shifting into P (Park) or setting the parking brake.
This message is followed by the MAXIMUM SPEED 90 km/h (55 MPH) message, and then by the REDUCED HANDLING message. The Active Handling System will intervene more quickly when a flat tire has been detected. Adjust your driving accordingly . Y ou can receive more than one tire pressure message at a time.
TRACTION SYSTEM AND ACTIVE HANDLING – OFF This message displays, the instrument panel cluster light turns on, and a sound will be heard when the T raction Control System (TCS) and Active Handling System are turned off by pressing the Active Handling System button on the console for five seconds.
TRANSMISSION HOT IDLE ENGINE This message displays and four chimes sound if the transmission fluid temperature rises above 132°C (270°F) or rises rapidly . The transmission may shift gears or apply the torque converter clutch to reduce the fluid temperature.
Other Messages Here are more messages that you can receive on your Driver Information Center (DIC). T o acknowledge a message and read another message that may have come on at the same time, press the RESET button. . ACCESSORY MODE ON . BA TTERY VOL T AGE HIGH See V oltmeter Gauge on page 4 ‑ 35 .
DIC V ehicle Personalization Many features on your vehicle can be personalized. This means that the operation of these features can be set to operate differently depending on who is driving the vehicle. See “ Personal Options ” later in this section for the features that you can personalize.
Entering the Personal Options Menu T o enter the personal options menu, use the following steps: 1. If you have an automatic transmission vehicle, turn the vehicle on with the shift lever in P (Park). If you have a manual transmission vehicle, turn the vehicle on with the parking brake set.
Press the OPTION button until AUTO MEMORY RECALL appears on the display , then press the RESET button to scroll through the following modes: . YES . NO (default) If you choose YES, the driver's seat, the outside rearview mirrors and the telescopic steering column, if your vehicle has this feature, positions are recalled when you turn the ignition on.
Approach Lights : This option briefly turns on the parking lamps, the high-beam headlamps and the back-up lamps during low light periods when the keyless access transmitter is used to unlock the vehicle. Press the OPTION button until APPROACH LIGHTS appears on the display , then press the RESET button to scroll through the following modes: .
If you choose 90 S, the twilight delay time will be set to 90 seconds. When the mode you want is selected, press the OPTION button to set your choice and advance to the next personal option. Flash at Unlock : This option activates the front and rear turn signals for two short flashes when the unlock or hatch/trunk button on the keyless access transmitter is pressed.
FOB Reminder : This option sounds the horn three times when the driver's door is closed and there is a keyless access transmitter inside the interior of the vehicle. This will only occur when the vehicle is off. Press the OPTION button until FOB REMINDER appears on the display , then press the RESET button to scroll through the following modes: .
If you choose HORN, the doors will automatically lock and the horn will sound a short time after you remove a keyless access transmitter from the interior of the vehicle and close both doors. If you are parking in a quiet area and do not want the horn to sound when the doors lock, press the lock button on the keyless access transmitter immediately after removing it from the interior and closing the doors.
When the mode you want is selected, press the OPTION button to set your choice and advance to the next personal option. Language : This option allows you to select the language the DIC, the Head-Up Display (HUD), if your vehicle has this feature, and the radio uses to display messages.
4. Press the OPTION button and a cursor will display where you can insert a letter . 5. Press the OPTION button again until the letter you want is displayed. T o scroll through the letters faster and without a beeping noise, keep the OPTIONS button depressed.
Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. { W ARNING: T aking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others.
Radio(s) Single CD Radio shown, Six-Disc CD Radio similar The vehicle has one of these radios as its audio system. An indicator light on the upper left side of the radio flashes when the ignition is off, to indicate the theft deterrent feature is set.
Audio Settings Press and hold O e when no tone or speaker control is displayed to adjust all tone and speaker controls to the middle position. AUDIO SETTINGS CENTERED displays. Adjusting the T one (Bass/T reble) O e (Bass/T reble): T o adjust the Bass or Treble: Press and release O e until BASS or TREBLE displays.
AUTO n (Automatic V olume): Automatic volume automatically adjusts the audio system to make up for road and wind noise, by increasing the volume as vehicle speed increases. For vehicles without the Bose ® sound system: 1. Set the volume at the desired level.
Using the Radio Radio Data System (RDS) RDS features are available for use only on FM stations that broadcast RDS information. The station name or call letters display while the radio is tuned to an RDS station. This system relies upon receiving specific information from these stations and works only when the information is available.
T o scan preset stations: Press and hold t or u for four seconds until PRESET SCAN displays. The radio goes to the next preset station, plays for a few seconds, then goes to the next preset station. Press t or u again or one of the pushbuttons to stop scanning presets.
SCAN : T o scan the stations within a category: 1. Press CA T . The last selected category displays. 2. T urn the O e knob to select a category . 3. Press and hold t or u until a beep sounds and SCAN CA TEGORY displays. The radio begins scanning the stations in the category .
TRAF (T raffic) : T A (traffic) displays when the station broadcasts traffic announcements, the announcement will be played. Press TRAF and the radio seeks to a station that broadcasts traffic announcements. When a station is found, the radio stops seeking and T A displays.
T o insert multiple CDs: 1. Press and hold M for two seconds. Two beeps sound and LOAD ALL DISCS displays. 2. Load a CD and insert the CD partway into the slot, label side up when INSERT CD # displays. The player pulls the CD in. 3. W ait for INSERT CD # to display after the previous CD is loaded, then load the next CD.
Six-Disc CD Radio: Press X to eject the CD that is currently playing. T o eject multiple CDs: 1. Press and hold X for two seconds. A beep sounds and EJECT ALL displays. 2. The ejected CD can be removed when REMOVE DISC displays. T o stop ejecting the CDs, press the M or X .
R (Song List): The Song List feature can save 20 track selections. T o save tracks: 1. If S-LIST is displayed, press R to turn it off. 2. Select the desired CD by pressing the numbered pushbutton and then use u or O e knob to select the track to be saved.
Care of CDs and the CD Player Care of CDs Store CD(s) in their original cases or other protective cases and away from direct sunlight and dust. The CD player scans the bottom of the disc. If the bottom of a CD is damaged it may not play properly or at all.
Connect a 3.5 mm (1/8 in.) cable to the radio ’ s front auxiliary input jack to use a portable audio player . The radio displays AUX INPUT DEVICE when a device is connected and begins playing audio from that device. T op Knob (Power/V olume) : T urn to increase or decrease the volume of the portable player .
Supported Bit Rates The following bit rates are supported: 32 kbps, 40 kbps, 56 kbps, 64 kbps, 80 kbps, 96 kbps, 1 12 kbps, 128 kbps, 160 kbps, 192 kbps, 224 kbps, 256 kbps, and 320 kbps or a variable bit rate. File Naming ID3v1 and ID3v2 tags are supported.
| (Next Folder): Press to go to the first track in the next folder . Press and hold to fast forward the current track. RDM (Random) : Press to hear the tracks in random, rather than sequential order , on one CD, one folder , or all of the loaded CDs. Press and release RDM until: .
XM Radio Messages XL (Explicit Language Channels) : These channels, or any others, can be blocked by calling 1-800-852-XMXM (9696). Updating : The encryption code in the receiver is being updated, and no action is required. This process should take no longer than 30 seconds.
Navigation/Radio System For vehicles with a navigation radio system, see the separate Navigation System manual. Bluetooth ® V ehicles with a Bluetooth system can use a Bluetooth capable cell phone with a Hands Free Profile to make and receive phone calls.
Pairing A Bluetooth enabled cell phone must be paired to the in ‐ vehicle Bluetooth system first and then connected to the vehicle before it can be used. See the cell phone manufacturers user guide for Bluetooth functions before pairing the cell phone.
Listing All Paired and Connected Phones 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Bluetooth ” . The system responds with “ Bluetooth ready ” followed by a tone. 3. Say “ List ” .
Using the Store Command The store command allows a phone number to be stored without entering the digits individually . 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Store ” . The system responds with “ Store, number please ” followed by a tone.
3. Say the first digit to be stored. The system will repeat back the digit it heard followed by a tone. Continue entering digits until the number to be stored is complete. . If an unwanted number is recognized by the system, say “ Clear ” at any time to clear the last number .
3. Say the name tag to be deleted. The system responds with “ Would you like to delete, <name tag>? Please say yes or no ” . . If the name tag is correct, say “ Y es ” to delete the name tag. The system responds with “ OK, deleting <name tag>, returning to the main menu.
Using the Digit Dial Command 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. Say “ Digit Dial ” . The system responds with “ Digit dial using <phone name>, please say the first digit to dial ” followed by a tone.
Using the Re ‐ dial Command 1. Press and hold b g for two seconds. The system responds with “ Ready ” followed by a tone. 2. After the tone, say “ Re ‐ dial ” . The system responds with “ Re ‐ dial using <phone name> ” and dials the last number called from the connected Bluetooth phone.
Ending a Call Press c to end a call. Muting a Call During a call, all sounds from inside the vehicle can be muted so that the person on the other end of the call cannot hear them. T o Mute a call 1. Press b g . The system responds with “ Ready ” followed by a tone.
V oice Pass-Thru V oice Pass ‐ Thru allows access to the voice recognition commands on the cell phone. See the cell phone manufacturers user guide to see if the cell phone supports this feature. This feature can be used to verbally access contacts stored in the cell phone.
Sending a Stored Name T ag During a Call 1. Press b g . The system responds with “ Ready ” followed by a tone. 2. Say “ Send name tag. ” The system responds with “ Say a name tag to send tones ” followed by a tone. 3. Say the name tag to send.
Audio Steering Wheel Controls For vehicles with steering wheel controls, some audio controls can be adjusted at the steering wheel. b g (Mute/Push to T alk): Press to silence the vehicle speakers only . Press again to turn the sound on. For vehicles with Bluetooth or OnStar ® systems press and hold b g for longer than two seconds to interact with those systems.
T o select tracks on a CD: . Press w or x to go to the next or to the previous track when a CD is playing. . Press and hold w or x for more than two seconds to scan the current CD. The CD goes to the next track, plays the first 10 seconds, then goes to the next track.
XM ™ Satellite Radio Service XM Satellite Radio Service gives digital radio reception from coast-to-coast in the 48 contiguous United States, and in Canada. Just as with FM, tall buildings or hills can interfere with satellite radio signals, causing the sound to fade in and out.
2 NOTES 4-1 10.
Section 5 Driving Y our V ehicle Y our Driving, the Road, and the V ehicle . . . . . . . . . . 5-2 Defensive Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 D r u n k D r i v i n g ... ................................ 5 - 2 Control of a V ehicle .
Y our Driving, the Road, and the V ehicle Defensive Driving Defensive driving means “ always expect the unexpected. ” The first step in driving defensively is to wear your safety belt — See Safety Belts: They Are for Everyone on page 2 ‑ 9 . { W ARNING: Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes.
For persons under 21, it is against the law in every U.S. state to drink alcohol. There are good medical, psychological, and developmental reasons for these laws. The obvious way to eliminate the leading highway safety problem is for people never to drink alcohol and then drive.
Braking See Brake System Warning Light on page 4 ‑ 36 . Braking action involves perception time and reaction time. Deciding to push the brake pedal is perception time. Actually doing it is reaction time. Average reaction time is about three ‐ fourths of a second.
Antilock Brake System (ABS) This vehicle has the Antilock Brake System (ABS), an advanced electronic braking system that helps prevent a braking skid. When the engine is started and the vehicle begins to drive away , ABS checks itself. A momentary motor or clicking noise might be heard while this test is going on, and it might even be noticed that the brake pedal moves a little.
Braking in Emergencies ABS allows the driver to steer and brake at the same time. In many emergencies, steering can help more than even the very best braking. Brake Assist This vehicle has a brake assist feature that responds to emergency braking by generating additional pressure and engaging the ABS.
The SERVICE TRACTION SYSTEM message and the TCS warning light will come on if there is a problem with TCS. See DIC Warnings and Messages on page 4 ‑ 52 . When this light and the SERVICE TRACTION SYSTEM message are on, the system will not limit wheel spin.
Active Handling System The Active Handling System is a computer controlled system that helps the driver maintain directional control of the vehicle in difficult driving conditions. This is accomplished by selectively applying any one of the vehicle's brakes.
If the T ire Pressure Monitor (TPM) system detects a flat tire and the Driver Information Center (DIC) displays TIRE FLA T , or if the TPM system is malfunctioning and the DIC displays SERVICE TIRE MONIT OR, the Active Handling System will be affected as follows: .
This light is on when the vehicle is in the Competitive Driving Mode. This optional handling mode can be selected by pressing the ACTIVE HANDLING button on the console quickly two times. COMPETITIVE DRIVING MODE displays in the Driver Information Center (DIC).
T o experience the performance benefit of this system, after entering a curve and at the point where the driver would normally start to increase acceleration, the accelerator pedal can be fully pressed. The Performance T raction Management system will modify the level of engine power for a smooth and consistent corner exit.
PERF TRAC 3 – SPORT ACTIVE HANDLING ON . For use by drivers who are familiar with the track . Dry conditions only . Requires more driving skill than mode 2 . Active Handling is on and more engine power is available than in mode 2 PERF TRAC 4 – SPORT ACTIVE HANDLING OFF .
Launch Control A Launch Control feature is available, within Competitive Driving Mode (except ZR1) or Performance T raction Management (ZR1), on vehicles with a manual transmission to allow the driver to achieve high levels of vehicle acceleration in a straight line.
Limited-Slip Rear Axle V ehicles with a limited-slip rear axle can give more traction on snow , mud, ice, sand or gravel. It works like a standard axle most of the time, but when traction is low , this feature allows the drive wheel with the most traction to move the vehicle.
Three Driver Information Center (DIC) messages (SERVICE RIDE CONTROL, SHOCKS INOPERA TIVE and MAXIMUM SPEED 80 MPH (129 KM/H) display when a malfunction occurs with the Selective Ride Control system . Refer to DIC Warnings and Messages on page 4 ‑ 52 for more information.
Steering Power Steering If power steering assist is lost because the engine stops or the system is not functioning, the vehicle can be steered but it will take more effort. Magnetic Speed V ariable Assist Steering System This system continuously adjusts the effort felt when steering at all vehicle speeds.
An emergency like this requires close attention and a quick decision. If holding the steering wheel at the recommended 9 and 3 o'clock positions, it can be turned a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly , and just as quickly straighten the wheel once you have avoided the object.
Passing Passing another vehicle on a two-lane road can be dangerous. T o reduce the risk of danger while passing: . Look down the road, to the sides, and to crossroads for situations that might affect a successful pass. If in doubt, wait. . W atch for traffic signs, pavement markings, and lines that could indicate a turn or an intersection.
If the vehicle starts to slide, ease your foot off the accelerator pedal and quickly steer the way you want the vehicle to go. If you start steering quickly enough, the vehicle may straighten out. Always be ready for a second skid if it occurs. Of course, traction is reduced when water , snow , ice, gravel, or other material is on the road.
After conversion to the high performance brake fluid, follow the brake fluid service recommendations outlined by the fluid manufacturer . Do not use silicone or DOT ‐ 5 brake fluids. If the vehicle is a Z06, ZR1, or Grand Sport model, it has greaseable outer ends on both of the rear toe ‐ links.
Street High Performance Brake Burnishing Procedure Run this procedure in a safe manner and in compliance with all local and state ordinances/laws regarding motor vehicle operation. Run this procedure only on dry pavement. 1. From a stop, accelerate as rapidly as possible without activating traction control to a speed of 97 kph (60 mph).
Driving at Night Night driving is more dangerous than day driving because some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Night driving tips include: . Drive defensively . . Do not drink and drive.
Hydroplaning Hydroplaning is dangerous. Water can build up under your vehicle's tires so they actually ride on the water . This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road.
Highway Hypnosis Always be alert and pay attention to your surroundings while driving. If you become tired or sleepy , find a safe place to park your vehicle and rest. Other driving tips include: . Keep the vehicle well ventilated. . Keep interior temperature cool.
{ W ARNING: Coasting downhill in N (Neutral) or with the ignition off is dangerous. The brakes will have to do all the work of slowing down and they could get so hot that they would not work well. Y ou would then have poor braking or even none going down a hill.
The Antilock Brake System (ABS) on page 5 ‑ 5 improves vehicle stability during hard stops on a slippery roads, but apply the brakes sooner than when on dry pavement. Allow greater following distance on any slippery road and watch for slippery spots.
W ARNING: (Continued) For more information about carbon monoxide, see Engine Exhaust on page 3 ‑ 37 . Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. Y ou cannot see it or smell it, so you might not know it is in your vehicle.
Rocking Y our V ehicle to Get It Out T urn the steering wheel left and right to clear the area around the front wheels. Turn the traction control system off. Shift back and forth between R (Reverse) and a forward gear , spinning the wheels as little as possible.
Tire and Loading Information Label Label Example A vehicle specific T ire and Loading Information label is attached to the center pillar (B-pillar) of your vehicle. With the driver's door open, you will find the label attached below the door latch.
4. The resulting figure equals the available amount of cargo and luggage load capacity . For example, if the “ XXX ” amount equals 1400 lbs and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1400 − 750 (5 x 150) = 650 lbs).
Example 2 Item Description T otal A V ehicle Capacity Weight for Example 2 = 400 lbs (181 kg) B Subtract Occupant Weight @ 150 lbs (68 kg) x 2 = 300 lbs (136 kg) C Available Cargo Weight = 100 lbs (45.
Refer to your vehicle's T ire and Loading Information label for specific information about your vehicle's capacity weight and seating positions. The combined weight of the driver , passengers and cargo should never exceed your vehicle's capacity weight.
If you put things inside your vehicle — like suitcases, tools, packages or anything else — they will go as fast as the vehicle goes. If you have to stop or turn quickly , or if there is a crash, they will keep going. { W ARNING: Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or in a crash.
2 NOTES 5-34.
Section 6 Service and Appearance Care Service ......... ........................... ......... 6-3 Accessories and Modifications . . . . . . . . . . . . . . . . . . 6-3 California Proposition 65 Warning . . . . . . . . . . . . . . . 6-4 California Perchlorate Materials R e q u i r e m e n t s .
Section 6 Service and Appearance Care Run-Flat T ires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-69 Inflation - T ire Pressure . . . . . . . . . . . . . . . . . . . . . . . . 6-70 High-Speed Operation . . . . . . . . . . . . .
Service For service and parts needs, visit your dealer/retailer . Y ou will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modifications When non ‐ dealer/non ‐ retailer accessories are added to the vehicle, they can affect vehicle performance and safety , including such things as airbags, braking, stability , ride and handling, emissions systems, aerodynamics, durability , and electronic systems like antilock brakes, traction control, and stability control.
Damage to vehicle components resulting from the installation or use of non ‐ GM certified parts, including control module modifications, is not covered under the terms of the vehicle warranty and may affect remaining warranty coverage for affected parts.
Doing Y our Own Service Work { W ARNING: Y ou can be injured and the vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. . Be sure you have sufficient knowledge, experience, the proper replacement parts, and tools before attempting any vehicle maintenance task.
Fuel Use of the recommended fuel is an important part of the proper maintenance of this vehicle. T o help keep the engine clean and maintain optimum vehicle performance, we recommend the use of gasoline advertised as TOP TIER Detergent Gasoline. Look for the TOP TIER label on the fuel pump to ensure gasoline meets enhanced detergency standards developed by auto companies.
Gasoline Octane If the vehicle has the 6.2L V8 engine (VIN Code W), use premium unleaded gasoline with a posted octane rating of 91 or higher . Y ou can also use regular unleaded gasoline rated at 87 octane or higher , but the vehicle's acceleration could be slightly reduced, and a slight audible knocking noise, commonly referred to as spark knock, might be heard.
Additives T o provide cleaner air , all gasolines in the United States are now required to contain additives that help prevent engine and fuel system deposits from forming, allowing the emission control system to work properly . In most cases, nothing should have to be added to the fuel.
Fuels in Foreign Countries If you plan on driving in another country outside the United States or Canada, the proper fuel might be hard to find. Never use leaded gasoline or any other fuel not recommended in the previous text on fuel. Costly repairs caused by use of improper fuel would not be covered by the vehicle warranty .
The fuel door release button is located on the instrument panel to the left of the steering wheel. Push the button to release the fuel door . There is also a manual fuel door release tab. It is located against the upper trim in the rear compartment on the driver side of the vehicle.
{ W ARNING: Fuel can spray out on you if you open the fuel cap too quickly . If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if the tank is nearly full, and is more likely in hot weather . Open the fuel cap slowly and wait for any hiss noise to stop.
Filling a Portable Fuel Container { W ARNING: Never fill a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor . Y ou can be badly burned and the vehicle damaged if this occurs.
Hood Release T o open the hood: 1. Pull the hood release lever with this symbol on it. It is located inside the vehicle below the instrument panel on the driver side. 2. Go to the side of the vehicle and pull up on the rear edge of the hood, near the windshield.
Engine Compartment Overview If the vehicle has the 6.2 L LS3 V8 engine (without the dry sump engine oil tank) and you are facing the front of the vehicle, when the hood is opened: 6-14.
A. Clutch Master Cylinder Reservoir (If Equipped). See Hydraulic Clutch on page 6 ‑ 31 . B. Windshield W asher Fluid Reservoir . See “ Adding W asher Fluid ” under Windshield Washer Fluid on page 6 ‑ 42 . C. Brake Fluid Reservoir . See “ Brake Fluid ” under Brakes on page 6 ‑ 43 .
If the vehicle has the 6.2 L LS9 Supercharged V8 engine and you are facing the front of the vehicle, when the hood is opened: 6-16.
A. Intercooler . See Cooling System (Engine) on page 6 ‑ 32 or Cooling System (Intercooler) on page 6 ‑ 33 . B. Engine Air Cleaner/Filter on page 6 ‑ 27 . C. Power Steering Fluid Reservoir and Cap. See Power Steering Fluid on page 6 ‑ 41 . D. Coolant Surge T ank and Pressure Cap.
If the vehicle has the 6.2 L LS3 V8 engine with the manual transmission (with the dry sump engine oil tank) or the 7.0 L LS7 V8 engine and you are facing the driver side of the vehicle, when the hood .
A. Engine Air Cleaner/Filter on page 6 ‑ 27 . B. Power Steering Fluid Reservoir . See Power Steering Fluid on page 6 ‑ 41 . C. Engine Compartment Fuse Block on page 6 ‑ 104 . D. Remote Positive (+) T erminal (Out of View). See Jump Starting on page 6 ‑ 50 .
When to Add Engine Oil (Except ZO6, ZR1, and Grand Sport) If the oil is below the cross-hatched area at the tip of the dipstick, add at least one liter/quart of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity , see Capacities and Specifications on page 6 ‑ 108 .
Checking Engine Oil (ZO6, ZR1, and Grand Sport) A. Engine Oil Dipstick B. Engine Oil Fill Cap It is a good idea to check the engine oil level at each fuel fill. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground.
cold engine dipstick readings. The engine oil level on the dipstick will also be inaccurate if checked while the engine is running. 1. T o obtain an accurate engine oil level reading, warm up the engine to at least 80°C (175°F). Cold oil will not give a correct oil level reading.
See Engine Compartment Overview on page 6 ‑ 14 for the location of the external engine oil tank and fill cap. Add enough oil to put the level somewhere in the proper operating range. Push the dipstick all the way back into the oil tank when through.
2. Once the oil has been drained from the engine, remove the engine oil filter and allow the oil to drain. 3. Re ‐ install both drain plugs and tighten them to 25 Y (18 lb ft). 4. Replace the oil filter and tighten it to 30 Y (22 lb ft). See Maintenance Replacement Parts on page 7 ‑ 12 for the correct filter .
Oils meeting these requirements should have the starburst symbol on the container . This symbol indicates that the oil has been certified by the American Petroleum Institute (API). This vehicle's engine was filled at the factory with a Mobil 1 ® synthetic oil meeting all requirements for this vehicle.
Z06, ZR1, and Grand Sport models have a racetrack ‐ ready dry sump engine lubrication system. This high ‐ performance system operates differently than a standard engine lubrication system and requires a special procedure when changing the engine oil and filter .
What to Do with Used Oil Used engine oil contains certain elements that can be unhealthy for your skin and could even cause cancer . Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water , or a good hand cleaner .
T o inspect or replace the engine air cleaner/filter: 1. Open the hood. See Hood Release on page 6 ‑ 13 . 6.2 L V8 Engine LS3 shown, 6.2 L V8 Engine LS9 and 7.0 L V8 Engine LS7 similar A. T ube B. Clamp C. Duct 2. Remove the tube (A) from the air cleaner assembly .
6.2 L V8 Engine LS3 6.2 L V8 Engine LS9 shown, 7.0 L V8 Engine LS7 similar 6. T o access the air filter element, gently pull the air cleaner assembly upward until the fasteners are released from the retainer pins in the upper radiator support. The LS3 engine has three retainer pins and the LS7 and LS9 engines have two.
6.2 L V8 Engine LS3 shown, 6.2 L V8 Engine LS9 and 7.0 L V8 Engine LS7 similar A. Screw B. Filter Cover C. Filter 7. T o remove the filter from the LS3 and LS7 engines, remove the six screws (A) securing the filter cover (B) then pull away from to gain access to the air filter (C).
Automatic T ransmission Fluid How to Check Automatic T ransmission Fluid It is not necessary to check the transmission fluid level. A transmission fluid leak is the only reason for fluid loss. If a leak occurs, take the vehicle to your dealer/ retailer service department and have it repaired as soon as possible.
When to Check and What to Use The hydraulic clutch fluid reservoir cap has this symbol on it. See Engine Compartment Overview on page 6 ‑ 14 for reservoir location. Refer to the Maintenance Schedule for the proper fluid to use. See Recommended Fluids and Lubricants on page 7 ‑ 10 .
{ W ARNING: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury . Keep hands, clothing, and tools away from any underhood electric fan. { W ARNING: Heater and radiator hoses, and other engine parts, can be very hot.
Checking Coolant 1. V erify that the engine and intercooler are no longer hot. 2. Place a cloth to absorb possible coolant loss under the driver's side bleeder valve (A). 3. Loosen, but do not completely unscrew the bleeder valve to check for coolant in the system.
What to Use { W ARNING: Adding only plain water to the cooling system can be dangerous. Plain water , or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle's coolant warning system is set for the proper coolant mixture.
The engine coolant surge tank is located toward the rear of the engine compartment on the driver side of the vehicle. See Engine Compartment Overview on page 6 ‑ 14 for more information on location. When the engine is cold, the coolant level should be at the FULL COLD mark on the coolant surge tank.
If coolant is needed, add the proper DEX-COOL ® coolant mixture directly to the surge tank, but be sure the cooling system is cool before this is done. 1. When the cooling system, including the coolant surge tank pressure cap and upper radiator hose, is no longer hot, remove the pressure cap.
4. With the coolant surge tank pressure cap off, start the engine and let it run until you can feel the upper radiator hose getting hot. Any time during this procedure, watch out for the engine cooling fan. By this time, the coolant level inside the coolant surge tank may be lower .
If you do decide to lift the hood , make sure the vehicle is parked on a level surface. Then check to see if the engine cooling fan is running. If the engine is overheating, the fan should be running. If it is not, do not continue to run the engine and have the vehicle serviced.
If No Steam Is Coming From Y our Engine If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: . Climbs a long hill on a hot day .
Overheated Engine Protection Operating Mode This emergency operating mode lets the vehicle be driven to a safe place, up to 50 miles (80 km), in an emergency situation. If an overheated engine condition exists and the messages COOLANT OVER TEMPERA TURE and REDUCED ENGINE POWER are displayed, along with the check engine light, an overheat protection mode which alternates firing groups of cylinders helps prevent engine damage.
How to Check Power Steering Fluid T o check the power steering fluid: 1. T urn the ignition off and let the engine compartment cool down. 2. Wipe the cap and the top of the reservoir clean. 3. Unscrew the cap and wipe the dipstick with a clean rag. 4.
Adding W asher Fluid Open the cap with the washer symbol on it. Add washer fluid until the tank is full. See Engine Compartment Overview on page 6 ‑ 14 for reservoir location. Notice: . When using concentrated washer fluid, follow the manufacturer's instructions for adding water .
Do not top off the brake fluid. Adding fluid does not correct a leak. If fluid is added when the linings are worn, there will be too much fluid when new brake linings are installed. Add or remove brake fluid, as necessary , only when work is done on the brake hydraulic system.
Notice: . Using the wrong fluid can badly damage brake hydraulic system parts. For example, just a few drops of mineral-based oil, such as engine oil, in the brake hydraulic system can damage brake hydraulic system parts so badly that they will have to be replaced.
Brake Wear (ZR1 Only) The ZR1 model does not have built-in brake pad wear indicators and periodic visual inspection of the brake pads is required to determine when to replace the brake pads. Notice: Continuing to drive with worn-out brake pads could result in costly brake repair.
Brake Rotor Wear ZR1 models have ceramic brake rotors. Rotors should be visually inspected whenever the brake pads are replaced. Rotors also need to be weighed before brake pads are replaced to confirm that the rotor mass is greater than the wear ‐ out mass printed on the rotor .
A rotor protector should always be installed before any wheel removal. The protector can be installed by feeding it through the wheel spokes and slipping it over the outer edge of the rotor . Leave the protector in place, over the rotor edge, until the wheel is re ‐ installed.
Battery Refer to the replacement number on the original battery label when a new battery is needed. For battery replacement, see your dealer/retailer or the service manual. T o purchase a service manual, see Service Publications Ordering Information on page 8 ‑ 16 .
Jump Starting If your battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely . { W ARNING: Batteries can hurt you. They can be dangerous because: . They contain acid that can burn you.
4. Open the hoods and locate the positive (+) and negative ( − ) terminal locations on each vehicle. 6.2 L LS3 shown, 7.0 L LS7 and 6.2 L LS9 similar Y our vehicle has a remote positive (+) terminal (A) and a remote negative ( − ) terminal (B), as shown in the illustration, which should be used to jump start your vehicle.
{ W ARNING: Using an open flame near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Be sure the battery has enough water . Y ou do not need to add water to the battery installed in your new vehicle.
6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery . Use a remote positive (+) terminal if the vehicle has one. 7. Do not let the other end touch metal. Connect it to the positive (+) terminal of the good battery . Use a remote positive (+) terminal if the vehicle has one.
Notice: If the jumper cables are connected or removed in the wrong order , electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty . Always connect and remove the jumper cables in the correct order , making sure that the cables do not touch each other or other metal.
Rear Axle When to Check Lubricant It is not necessary to regularly check rear axle fluid unless you suspect there is a leak or you hear an unusual noise. A fluid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant T o get an accurate reading, the vehicle should be on a level surface.
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 6 ‑ 58 . For any bulb changing procedure not listed in this section, contact your dealer/retailer . High Intensity Discharge (HID) Lighting { W ARNING: The low beam high intensity discharge lighting system operates at a very high voltage.
If the low-beam headlamp needs to be replaced, see your dealer/retailer . See High Intensity Discharge (HID) Lighting on page 6 ‑ 56 for more information. T o replace a high-beam or front parking/turn signal/ DRL bulb: 1. T urn the wheel to allow access to the wheel well.
T aillamps, T urn Signal, and Stoplamps T o replace a stoplamp, taillamp/turn signal bulb: 1. Remove the screw from the top of the lamp assembly . 2. T ilt the lamp assembly toward you. 3. T urn the bulb socket one-quarter turn counterclockwise and pull it out.
Windshield Replacement The windshield is part of the Head-Up Display (HUD) system. If you ever have to get the windshield replaced, get one that is designed for HUD or the HUD image may look out of focus. Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear and cracking.
A. Blade Assembly B. Arm Assembly C. Locking T ab D. Blade Pivot E. Hook Slot F . Arm Hook 3. Press down on the blade assembly pivot locking tab (C). Pull down on the blade assembly (A) to release it from the wiper arm hook (F). 4. Remove the insert from the blade assembly (A).
T o install the new wiper insert: 1. Slide the insert (D), notched end last, into the end with the two blade claws (A). Slide the insert all the way through the blade claws at the opposite end (B). The plastic caps (C) will be forced off as the insert is fully installed.
Tires Y our new vehicle comes with high-quality tires made by a leading tire manufacturer . If you ever have questions about your tire warranty and where to obtain service, see your vehicle W arranty booklet for details. For additional information refer to the tire manufacturer .
Low ‐ Profile Performance Tire The original equipment tires on your vehicle are classified as low ‐ profile performance tires. These tires are designed for very responsive driving on wet or dry pavement. Y ou may also notice more road noise with low ‐ profile tires and that they tend to wear faster .
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The example below shows a typical passenger (p ‐ metric) tire sidewall. Passenger (P ‐ Metric) Tire Example (A) Tire Size : The tire size is a combinati on of letters and numbers used to define a particular tire's width, height, aspect ratio, construction type, and service description.
(F) Uniform Tire Quality Grading (UTQG) : T ire manufacturers are required to grade tires based on three performance factors: treadwear , traction and temperature resistance. For more information see Uniform Tire Quality Grading on page 6 ‑ 79 . (G) Maximum Cold Inflation Load Limit : Maximum load that can be carried and the maximum pressure needed to support that load.
Tire T erminology and Definitions Air Pressure : The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight : This means the combined weight of optional accessories.
Intended Outboard Sidewall : The side of an asymmetrical tire, that must always face outward when mounted on a vehicle. Kilopascal (kPa) : The metric unit for air pressure. Light T ruck (L T ‐ Metric) Tire : A tire used on light duty trucks and some multipurpose passenger vehicles.
Radial Ply Tire : A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim : A metal support for a tire and upon which the tire beads are seated. Sidewall : The portion of a tire between the tread and the bead.
Run-Flat Tires This vehicle, when new , had run-flat tires. There is no spare tire, no tire changing equipment, and no place to store a tire in the vehicle. Run-flat tires perform so well without any air that a Tire Pressure Monitor System (TPMS) is used to alert you if a tire has lost pressure.
T o locate the nearest GM or run-flat servicing facility , call Roadside Assistance. For phone numbers and Roadside Service details see Roadside Assistance Program on page 8 ‑ 7 . { W ARNING: Run-flat tires are constructed differently than other tires and could explode during improper service.
A vehicle specific T ire and Loading Information label is attached to your vehicle. This label shows your vehicle's original equipment tires and the correct inflation pressures for your tires when they are cold. The recommended cold tire inflation pressure, shown on the label, is the minimum amount of air pressure needed to support your vehicle's maximum load carrying capacity .
High-Speed Operation { W ARNING: Driving at high speeds, 160 km/h (100 mph) or higher , puts an additional strain on tires. Sustained high-speed driving causes excessive heat build up and can cause sudden tire failure. Y ou could have a crash and you or others could be killed.
As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under ‐ inflated. Accordingly , when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure.
Tire Pressure Monitor Operation This vehicle may have a T ire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly on your vehicle.
TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle.
Tire Inspection and Rotation We recommend that you regularly inspect your vehicle's tires for signs of wear or damage Also check for damaged wheels. See When It Is Time for New Tires on page 6 ‑ 76 and Wheel Replacement on page 6 ‑ 81 . The tires on your vehicle are different sizes front to rear .
Y ou need a new tire if any of the following statements are true: . Y ou can see the indicators at three or more places around the tire. . Y ou can see cord or fabric showing through the tire's rubber . . The tread or sidewall is cracked, cut or snagged deep enough to show cord or fabric.
GM recommends replacing tires in sets of four . This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new . Replacing less than a full set of tires can affect the braking and handling performance of your vehicle.
Different Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this may affect the way your vehicle performs, including its braking, ride and handling characteristics, stability , and resistance to rollover .
While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors T ire Performance Criteria (TPC) standards. All Passenger Car Tires Must Conform to Federal Safety Requirements In Addition T o These Grades.
T emperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new GM original equipment parts. This way , you will be sure to have the right wheel, wheel bolts, and wheel nuts for your vehicle. { W ARNING: Using the wrong replacement wheels, wheel bolts, or wheel nuts on your vehicle can be dangerous.
Tightening Wheel Lug Nuts { W ARNING: Never use oil or grease on studs or the threads of the wheel nuts. If you do, the wheel nuts might come loose and the wheel could fall off, causing a crash. { W ARNING: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose and even come off.
Tire Chains { W ARNING: Do not use tire chains. There is not enough clearance. T ire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause you to lose control of the vehicle and you or others may be injured in a crash.
{ W ARNING: Getting under a vehicle when it is jacked up is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack. { W ARNING: Raising the vehicle with the jack improperly positioned can damage the vehicle or the vehicle may fall and cause your or others injury .
Lifting From the Front The front lifting points can be accessed from either side of your vehicle, behind the front tires. 1. Locate the front lifting points (A), according to the illustration shown. 2. Be sure to place a block or pad between the jack and the vehicle.
3. Lift the vehicle with the jack, making sure the jack spans at least two of the crossmember ribs (B). Lifting From the Rear The rear lifting points can be accessed from the rear of the vehicle, on either the driver's or passenger's side.
1. Locate the rear lifting points (A), according to the illustration shown. 2. Be sure to place a block or pad between the jack and the vehicle. 3. Lift the vehicle with the jack, making sure the jack spans at least two of the crossmember ribs (B). For more information, see Doing Y our Own Service Work on page 6 ‑ 5 .
If a Tire Goes Flat It is unusual for a tire to blow out while you are driving, especially if you maintain the tires properly . If air goes out of a tire, it is much more likely to leak out slowly . See Tires on page 6 ‑ 62 for additional information.
Appearance Care Interior Cleaning The vehicle's interior will continue to look its best if it is cleaned often. Although not always visible, dust and dirt can accumulate on the upholstery . Dirt can damage carpet, fabric, leather , and plastic surfaces.
Do not clean the vehicle using: . A knife or any other sharp object to remove a soil from any interior surface. . A stiff brush. It can cause damage to the vehicle's interior surfaces. . Heavy pressure or aggressive rubbing with a cleaning cloth.
T o clean: 1. Saturate a lint-free, clean white cloth with water or club soda. 2. Wring the cloth to remove excess moisture. 3. Start on the outside edge of the soil and gently rub toward the center . Continue cleaning, using a clean area of the cloth each time it becomes soiled.
Instrument Panel, Vinyl, and Other Plastic Surfaces A soft cloth dampened with water may be used to remove dust. If a more thorough cleaning is necessary , a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt.
W ashing Y our V ehicle The best way to preserve your vehicle's finish is to keep it clean by washing it often. Notice: Certain cleaners contain chemicals that can damage the emblems or nameplates on the vehicle. Check the cleaning product label.
Finish Care Occasional waxing or mild polishing of the vehicle by hand may be necessary to remove residue from the paint finish. Approved cleaning products can be obtained from your dealer/retailer . If the vehicle has a basecoat/clearcoat paint finish, the clearcoat gives more depth and gloss to the colored basecoat.
Windshield and Wiper Blades Clean the outside of the windshield with glass cleaner . Clean the rubber blades using a lint free cloth or paper towel soaked with windshield washer fluid or a mild detergent. W ash the windshield thoroughly when cleaning the blades.
Convertible T op The vehicle's convertible top should be cleaned often. However , high pressure car washes may cause water to enter your vehicle. When you hand wash the top, do it in partial shade. Use a mild soap, lukewarm water and a soft sponge.
cleaners with acid, or abrasive cleaning brushes on them because they could damage the surface. Do not use chrome polish on aluminum wheels. Notice: Using chrome polish on aluminum wheels could damage the wheels. The repairs would not be covered by the vehicle warranty .
Fiberglass Springs (Composite Springs) Notice: If you use acidic or corrosive cleaning products, engine degreasers or aluminum cleaning agents on fiberglass springs, you may damage the springs. The repairs would not be covered by your warranty . Use only approved cleaners when cleaning your vehicle's fiberglass springs.
Service Parts Identification Label This label, on the inside of the glove box, has the following information: . V ehicle Identification Number (VIN) . Model designation . Paint information . Production options and special equipment Do not remove this label from the vehicle.
Fuses and Circuit Breakers The wiring circuits in the vehicle are protected from short circuits by a combination of J-Case fuses, mini-fuses and circuit breakers. This greatly reduces the chance of fires caused by electrical problems. Look at the silver-colored band inside the fuse.
Fuses Usage BCK/UP LAMP Reverse Lamps BLANK Not Used BLANK Not Used Fuses Usage BTSI SOL/STR WHL LCK Brake T ransmission Shift Interlock, Steering Wheel Column Lock CLSTR/HUD Cluster , Heads ‐ Up Di.
Fuses Usage CTSY/LAMP Courtesy Lamp DR LCK Door Locks DRIV DR SWITCH Driver Door Switch ECM Engine Control Module (ECM) EXH MDL Exhaust Module (Z06 & ZR1), Spare (Coupe and Convertible) GM LAN RUN/CRNK GM LAN Devices HTD SEA T/ WPR RL Y Heated Seat, Wiper Relays HV AC/ PWR SND Heating.
Fuses Usage REAR/FOG Rear Fog Lamps TONNEAU RELSE T onneau Release TRUNK RELSE T runk Release Fuses Usage AUX PWR Auxiliary Power BLANK Not Used BLANK Not Used BLANK Not Used BLANK Not Used BLANK Not Used BLANK Not Used BLANK Not Used DRVR HTD SEA T Driver Heated Seat L TR Cigarette Lighter Fuses Usage P ASS HTD SEA T Passenger Heated Seat PWR SEA TS MSM Power Seats, Memory Seat Module PWR/ WNDWS/ TRUNK/FUEL RELSE Power Windows, Trunk, Fuel Door Release TRUNK RELSE T runk Release WPR DWELL Wiper Dwell WPR/WSW Windshield Wiper/W asher Engine Compartment Fuse Block There is one fuse block in the engine compartment located on the passenger side of the vehicle.
For ZR1 models, the Fuel System fuse is located at the battery . Fuse Usage 1 T ransmission Control Module/ T ransmission 2 Horn, Alternator Sense Fuse Usage 3 Antilock Braking System (ABS)/Real T ime.
Fuse Usage 6 Oxygen Sensor 7 Battery Main 5 8 Parking Lamps 9 Powertrain Relay Input/Electronic Throttle Control 10 Manual Transmission Solenoids 1 1 Antilock Braking System 12 Odd Numbered Fuel Injec.
Micro-Relays Usage 38 Front Fog Lamp 39 High-Beam Headlamp 46 Headlamp W asher 55 Fuel Pump (except ZR1) Mini-Relays Usage 40 Rear Defog 41 Windshield Wiper High/Low 42 Windshield Wiper Run/Accessory .
Capacities and Specifications The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 7 ‑ 10 for more information. Application Capacities Metric English Air Conditioning Refrigerant R134a For the air conditioning system refrigerant charge amount, see the refrigerant caution label located under the hood.
Application Capacities Metric English T ransmission Fluid Automatic T ransmission (Pan Removal and Filter Replacement) 6.2 L 6.5 qt Manual T ransmission – Base 3.5 L 3.6 qt Manual T ransmission – Z16 4.0 L 4.2 qt Manual T ransmission – Z06 4.3 L 4.
Engine Data Engine Horsepower T orque Displacement Compression Ratio 6.2L LS3 V8 without option NPP 430 @ 5900 rpm 424 lb ft @ 4600 rpm 6.2L 10.69:1 6.2L LS3 V8 with option NPP 436 @ 5900 rpm 428 lb ft @ 4600 rpm 6.2L 10.69:1 6.2L LS9 V8 Supercharged 638 @ 6500 rpm 604 lb ft @ 3800 rpm 6.
Section 7 Maintenance Schedule Maintenance Schedule ........................ .... 7-2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Scheduled Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Owner Checks and Services .
Maintenance Schedule Introduction Notice: Maintenance intervals, checks, inspections, recommended fluids, and lubricants are necessary to keep this vehicle in good working condition. Damage caused by failure to follow scheduled maintenance might not be covered by the vehicle warranty .
Scheduled Maintenance When the Change Engine Oil Message Displays Change engine oil and filter . See Engine Oil on page 6 ‑ 19 . An Emission Control Service. When the Change Engine Oil message displays, service is required for the vehicle as soon as possible, within the next 1 000 km/600 miles.
. T ire wear inspection. See Tire Inspection and Rotation on page 6 ‑ 76 . . Fluids visual leak check (or every 12 months, whichever occurs first). A leak in any system must be repaired and the fluid level checked. . Engine air cleaner filter inspection (vehicles driven in dusty conditions only).
Once a Month . T ire inflation check. See Inflation - Tire Pressure on page 6 ‑ 70 . . T ire wear inspection. See Tire Inspection and Rotation on page 6 ‑ 76 . Once a Y ear . Starter switch check. See Owner Checks and Services on page 7 ‑ 8 . . Parking brake and automatic transmission P (Park) mechanism check.
First Engine Oil Change After Every 80 000 km/50,000 Miles . Engine air cleaner filter replacement. See Engine Air Cleaner/Filter on page 6 ‑ 27 . . Automatic transmission fluid change (severe service) for vehicles mainly driven in heavy city traffic in hot weather , in hilly or mountainous terrain, when frequently towing a trailer , or used for taxi, police, or delivery service.
Scheduled Maintenance Service Maintenance I Maintenance II Change engine oil and filter . Reset oil life system. • • Engine coolant level check. • • Windshield washer fluid level check. • • T ire inflation pressures check. • • T ire wear inspection.
Owner Checks and Services Starter Switch Check { W ARNING: When you are doing this inspection, the vehicle could move suddenly . If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle.
Parking Brake and Automatic T ransmission P (Park) Mechanism Check { W ARNING: When you are doing this check, the vehicle could begin to move. Y ou or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll.
Recommended Fluids and Lubricants Fluids and lubricants identified below by name, part number , or specification can be obtained from your dealer/retailer . Usage Fluid/Lubricant Engine Oil The engine requires a special engine oil meeting GM Standard GM4718M.
Usage Fluid/Lubricant Manual T ransmission Manual Transmission Fluid (GM Part No. U.S. 88861800, in Canada 88861801). Automatic T ransmission DEXRON ® -VI Automatic T ransmission Fluid. Key Lock Cylinders Multi-Purpose Lubricant, Superlube (GM Part No.
Maintenance Replacement Parts Replacement parts identified below by name, part number , or specification can be obtained from your dealer/retailer . Part GM Part Number ACDelco Part Number Engine Air Cleaner/Filter 6.2L LS3 V8 and 7.0L LS7 V8 Engines 15776148 A3077C 6.
Engine Drive Belt Routing 6.2L LS3 V8, 7.0L LS7 V8 Engines 6.2L LS9 V8 Engine 7-13.
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided.
Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 7-15.
Maintenance Record (cont'd) Date Odometer Reading Serviced By Services Performed 7-16.
Section 8 Customer Assistance Information Customer Assistance and Information . . . . . . . . . . . 8-2 Customer Satisfaction Procedure . . . . . . . . . . . . . . . 8-2 Online Owner Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Customer Assistance for T ext T elephone (TTY) U s e r s .
Customer Assistance and Information Customer Satisfaction Procedure Y our satisfaction and goodwill are important to your dealer and to Chevrolet. Normally , any concerns with the sales transaction or the operation of the vehicle will be resolved by the dealer's sales or service departments.
STEP THREE — U.S. Owners : Both General Motors and your dealer are committed to making sure you are completely satisfied with your new vehicle. However , if you continue to remain unsatisfied after following the procedure outlined in Steps One and T wo, you can file with the Better Business Bureau (BBB) Auto Line Program to enforce your rights.
STEP THREE — Canadian Owners : In the event that you do not feel your concerns have been addressed after following the procedure outlined in Steps 1 and 2, General Motors of Canada Limited wants you to be aware of its participation in a no-charge Mediation/ Arbitration Program.
Online Owner Center Online Owner Center (U.S.) — www .gmownercenter .com/chevrolet Information and services customized for your specific vehicle — all in one convenient place. . Digital owner manual, warranty information, and more . Online service and maintenance records .
Customer Assistance for T ext T elephone (TTY) Users T o assist customers who are deaf, hard of hearing, or speech-impaired and who use T ext T elephones (TTYs), Chevrolet has TTY equipment available at its Customer Assistance Center . Any TTY user in the U.
Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.V . Customer Assistance Center Paseo de la Reforma # 2740 Col. Lomas de Bezares C.P .
. Odometer reading, V ehicle Identification Number (VIN), and delivery date of the vehicle . Description of the problem Coverage Services are provided up to 5 years/100,000 miles (160 000 km), whichever comes first. In the U.S., anyone driving the vehicle is covered.
Services Not Included in Roadside Assistance . Impound towing caused by violation of any laws. . Legal fines. . Mounting, dismounting or changing of snow tires, chains, or other traction devices. . T owing or services for vehicles driven on a non-public road or highway .
Scheduling Service Appointments When your vehicle requires warranty service, contact your dealer/retailer and request an appointment. By scheduling a service appointment and advising your service consultant of your transportation needs, your dealer/retailer can help minimize your inconvenience.
Public T ransportation or Fuel Reimbursement If your vehicle requires overnight warranty repairs, and public transportation is used instead of the dealer's shuttle service, the expense must be supported by original receipts and can only be up to the maximum amount allowed by GM for shuttle service.
Collision Damage Repair If your vehicle is involved in a collision and it is damaged, have the damage repaired by a qualified technician using the proper equipment and quality replacement parts. Poorly performed collision repairs diminish your vehicle's resale value, and safety performance can be compromised in subsequent collisions.
Insuring Y our V ehicle Protect your investment in your GM vehicle with comprehensive and collision insurance coverage. There are significant differences in the quality of coverage afforded by various insurance policy terms. Many insurance policies provide reduced protection to your GM vehicle by limiting compensation for damage repairs by using aftermarket collision parts.
. If your vehicle cannot be driven, know where the towing service will be taking it. Get a card from the tow truck operator or write down the driver's name, the service's name, and the phone number. . Remove any valuables from your vehicle before it is towed away .
Managing the V ehicle Damage Repair Process In the event that your vehicle requires damage repairs, GM recommends that you take an active role in its repair . If you have a pre-determined repair facility of choice, take your vehicle there, or have it towed there.
Reporting Safety Defects to the Canadian Government If you live in Canada, and you believe that your vehicle has a safety defect, notify Transport Canada immediately , in addition to notifying General Motors of Canada Limited. Call them at 1-800-333-0510 or write to: T ransport Canada Road Safety Branch 2780 Sheffield Road Ottawa, Ontario K1B 3V9 Reporting Safety Defects to General Motors In addition to notifying NHTSA (or T ransport Canada) in a situation like this, please notify General Motors.
Owner Information Owner publications are written specifically for owners and intended to provide basic operational information about the vehicle. The owner manual includes the Maintenance Schedule for all models. In-Portfolio: Includes a Portfolio, Owner Manual, and W arranty Booklet.
V ehicle Data Recording and Privacy Y our GM vehicle has a number of sophisticated computers that record information about the vehicle ’ s performance and how it is driven. For example, your vehicle uses computer modules to monitor and control engine and transmission performance, to monitor the conditions for airbag deployment and deploy airbags in a crash and, if so equipped, to provide antilock braking to help the driver control the vehicle.
Important: EDR data is recorded by your vehicle only if a non-trivial crash situation occurs; no data is recorded by the EDR under normal driving conditions and no personal data (e.g., name, gender , age, and crash location) is recorded. However , other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation.
Radio Frequency Identification (RFID) RFID technology is used in some vehicles for functions such as tire pressure monitoring and ignition system security , as well as in connection with conveniences such as key fobs for remote door locking/unlocking and starting, and in-vehicle transmitters for garage door openers.
A Accessories and Modifications . . . . . . . . . . . . . . . . . . . . . . . 6-3 Accessory Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24 Accessory Power Outlets . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20 Active Handling System .
Ashtray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21 Assistance Program, Roadside . . . . . . . . . . . . . . . . . . . . . . 8-7 Audio System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Carbon Monoxide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14 Engine Exhaust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-37 Winter Driving . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Coolant Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-34 Engine T emperature Gauge . . . . . . . . . . . . . . . . . . . . . . 4-40 Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . . .
E EDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18 Electrical Equipment, Add-On . . . . . . . . . . . . . . . . . . . . 6-100 Electrical System Engine Compartment Fuse Block . . . . . . . . . . . .
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6 Additives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8 California Fuel . . . . . . . . . . . . . . . .
Headlamps (cont.) High/Low Beam Changer . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 On Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12 Wiper Activated . . . . . . . . . . . . . . . . . . . . . . . . .
Latches, Seatback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 Lifting the V ehicle, Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-84 Lighting Entry/Exit . . . . . . . . . . . . . . . . . . . . . . . . . . .
Memory Seat, Mirrors, Steering Wheel Controls . . . . .2-4 Message DIC Warnings and Messages . . . . . . . . . . . . . . . . . . . . . 4-52 Mirrors Automatic Dimming Rearview . . . . . . . . . . . . . . . . . . . . . 3-39 Outside Automatic Dimming Mirror .
Passenger Airbag Status Indicator . . . . . . . . . . . . . . . . . 4-34 Passenger Compartment Air Filter . . . . . . . . . . . . . . . . . 4-28 Passenger Sensing System . . . . . . . . . . . . . . . . . . . . . . . 2-53 Passing . . . . . . . . . . . .
Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-58 Replacement Parts Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12 Reporting Safety Defects Canadian Government . . . . .
Securing a Child Restraint Right Front Seat Position . . . . . . . . . . . . . . . . . . . . . . . . . 2-40 Security Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-45 Selective Ride Control . . . . .
T ires (cont.) High-Speed Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-72 If a T ire Goes Flat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-89 Inflation - T ire Pressure . . . . . . . . . . . . . . . . . . .
V ehicle Identification Number (VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-99 Service Parts Identification Label . . . . . . . . . . . . . . . . 6-100 V ehicle Personalization DIC . . . . . . . . . . . . . . . . .
An important point after buying a device Chevrolet 2010 Corvette Convertible (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Chevrolet 2010 Corvette Convertible yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Chevrolet 2010 Corvette Convertible - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Chevrolet 2010 Corvette Convertible you will learn all the available features of the product, as well as information on its operation. The information that you get Chevrolet 2010 Corvette Convertible will certainly help you make a decision on the purchase.
If you already are a holder of Chevrolet 2010 Corvette Convertible, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Chevrolet 2010 Corvette Convertible.
However, one of the most important roles played by the user manual is to help in solving problems with Chevrolet 2010 Corvette Convertible. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Chevrolet 2010 Corvette Convertible along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
