Instruction/ maintenance manual of the product 7201560 Char-Broil
Go to page of 16
P/N 42804297 (10-02-07) T ools needed f or assembl y: 2 Adjustable Wrenches 7/16” Open-End W rench Flat Screwdriver 04201101 07201560 Smok er , BBQ and Grill CA UTION Some parts may contain sharp edges.
K ey # Part N umb er D es cr iption Qu antit y A 55 71 0 23 2 SILVE R SMO KE CH AM B E R K IT 1 B 29 00 1 71 2 FIR E B OX TO P 1 C 55 71 0 23 4 FIR E B OX B OTT OM K IT 1 D 55 71 0 23 5 WOO D SH E LF .
Attach leg braces to the outside of one leg assembly using #10-24x1-3/4” screws and #10-24 flange nuts . Make sure slotted (oval) hole is toward bottom of leg . DO NOT FULL Y TIGHTEN screws until Step 6 is complete. 2 1 FIRST , GET A HELPER! This unit is heavy and requires a second person for lifting and moving.
3 Lay the leg assembly on its side with legs braces pointing upward. Insert the wood rack hooks into leg holes and swing rack upward, parallel to leg braces. 4 With the aid of a helper , place leg holes of remaining leg assembly over wood rack hooks and rotate leg assembly until it meets the leg braces.
6 5 Insert a cotter pin into the hole at one end of the axle and bend the ends of the pin back so that it cannot be removed. Slide a wheel onto the axle. Slide the axle through the holes at the ends of the short legs. Slide remaining wheel onto axle and secure with remaining cotter pin.
7 8 Attach Firebox T op Assembly to Firebox Bottom Assembly using eight 1/4-20x3/4” hex-head bolts as shown below . NOTE: Smoker chamber and firebox doors not pictured for clarity . TM TM Diamond Fire Plate Installation - For models without Diamond Fire ignitor accessory , part number 22504850.
9 10 Smokestack Smokestack plate NOTE: Smoker chamber door not pictured for clarity . From inside the smoker chamber , slide the smokestack through the large hole. Align the two holes in the smokestack plate with the holes in the chamber and secure with two 1/4-20x3/4” hex-head bolts outside the chamber and 1/4-20 flange nuts inside.
1 1 12 NOTE: Smoker chamber door not pictured for clarity . Install grate support screws in the four rear holes and two front-center holes in the smoker chamber . Use six #10-24x1” screws and #10 flange nuts . NOTE: Smoker chamber door not pictured for clarity .
Hole plug NOTE: Smoker chamber door not pictured for clarity . First , attach shelf slats to the two outer holes in shelf brackets using two #10-24x1” screws and #10-24 flange nuts per slat. DO NOT FULL Y TIGHTEN SCREWS . Second , fully tighten hex-head bolts on shelf brackets (installed in previous step).
16 15 Hang grease clip from holes on bottom right side of smoker chamber. A 12 oz. soup or vegetable can will fit nicely into clip to collect grease. Grease Clip If logo plate is not already installed, insert logo plate pins into two holes in lower right corner of smoker chamber door .
18 17 NOTE: Smoker chamber door not pictured for clarity . If you wish to grill in the smoker chamber , place two of the three wire fire grates into bottom of smoker chamber . Place two large porcelain cooking grates into chamber , resting them on the grate support screws.
19 Firebox Cooking Grate Installation for Grilling: NOTE: Firebox door not pictured for clarity . Insert small porcelain cooking grate into firebox. Small Porcelain Cooking Grate (1).
WARNING MOST SURF ACES ON THIS UNIT ARE HOT WHEN IN USE. USE EXTREME CAUTION. KEEP OTHERS A W A Y FROM UNIT . AL W A YS WEAR PROTECTIVE CLOTHING TO PREVENT INJUR Y . HARD WARE LIST Hardware is shown actual size. Y ou may have spare hardware after assembly is complete.
Preparing and Using Y our Silver Smoker Before cooking with your Silver Smoker , the following steps should be closely followed to both cure the finish and season the interior steel. Failure to properly follow these steps may damage the finish and/or impart metallic flavors to your first foods.
Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated below beginning on the date of purchase.
Char-Broil, LLC • Columbus, GA 31904 • Assembly Instructions © 2007 Printed in China.
An important point after buying a device Char-Broil 7201560 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Char-Broil 7201560 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Char-Broil 7201560 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Char-Broil 7201560 you will learn all the available features of the product, as well as information on its operation. The information that you get Char-Broil 7201560 will certainly help you make a decision on the purchase.
If you already are a holder of Char-Broil 7201560, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Char-Broil 7201560.
However, one of the most important roles played by the user manual is to help in solving problems with Char-Broil 7201560. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Char-Broil 7201560 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
