Instruction/ maintenance manual of the product FF880 CDA
Go to page of 12
1 Customer Care Department • The Group Ltd. • Harb y Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .
2 Impor tant The CD A Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidat e the guarantee supplied with this pr oduct f ollowing incorrect installation or misuse of the appliance.
3 Before F irst Use Y ou must allow the freezer to settle for at least twenty four hours prior to swit ching the power on. It is recommended that you clean the interior of the appliance prior to rst use, using a solution of bicar bonate of soda and warm water and then thoroughly drying the interior .
4 Contr ol Panel Switching the freezer on and o T o switch on the freezer for the rst time, press and hold the On/O key (A) for thr ee seconds. The freezer will beep twice, and will run at the factory preset temperature of -18 ° . T o switch the freezer o, pr ess and hold the On/O key for three seconds.
5 Super freeze function The super freez e function can be used to fr eeze large quantities of fresh food as quickly as possible . This function can be set for specic durations before swit ching o automatically for conv enience.
6 Care and Cleaning Always disconnect the appliance from the po wer before any cleaning or main tenance. • The r efrigerator should be cleaned using a solution of bicarbonate of soda and lukewarm water . • Do not use abrasive pr oducts or detergents.
7 T roubleshooting If you have any pr oblems with your appliance, you should check the tr oubleshooting prior to calling CDA Customer Car e to prevent unnecessary service calls and potential cost. If the appliance is not working • Check there is po wer to the appliance.
8 Installation and V entilation This appliance must never be installed close to heat sour ces i.e. heating elements, cookers or in damp places. The diagram shows the v entilation requirements f or your product.
9 Reversing the Door We r ecommend you seek the help of another individual to support the doors whilst performing this operation. 1. Carefully remov e the two hinge cover plates and two c over caps from the control panel . 2. Remove the control panel, ensuring that the wires are not damaged.
10 g. 9 Reversing the door 6. Remove the lower hinge and r eposition the lower hinge pin as shown in gure 7. 7. Reposition the lower hinge on the opposite side as shown in g 9. 8. Reverse the upper hinge pin as shown in g 8. 9. Locate the door on the low er hinge pin, then locate the upper hinge pin in the door .
11 Electrical information Warning! This appliance must be ear thed. The mains lead of this appliance has been tted with a BS 1363A 13 amp fused plug. T o change a fuse in this type of plug, follow the steps below: 1. R emove the fuse c over and fuse.
12 Customer Care Department • The Group Ltd. • Harb y Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www.cda.eu Passionate about style T o contact our Customer Car e Depar tment, or f or Ser vice, please contact us on the details below .
An important point after buying a device CDA FF880 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought CDA FF880 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data CDA FF880 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, CDA FF880 you will learn all the available features of the product, as well as information on its operation. The information that you get CDA FF880 will certainly help you make a decision on the purchase.
If you already are a holder of CDA FF880, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime CDA FF880.
However, one of the most important roles played by the user manual is to help in solving problems with CDA FF880. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device CDA FF880 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
