Instruction/ maintenance manual of the product EVPK90 CDA
Go to page of 20
1 Customer Care Department • The Group Ltd. • Harb y Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .
2 Impor tant The manufacturer cannot be held responsible for injuries or losses caused by inc orrect use or installation of this product. Please note that the manufacturer reserves the right to invalidat e the guarantee supplied with this product following incorr ect installation or misuse of the appliance or use in a commercial en vironment.
3 Using your Extractor For best performance, y ou should switch on the extractor 15 minutes before starting to cook and leave it to run f or approximately 15 minutes after the end of cooking.
4 Care and Maintenanc e IMPORT ANT : DO NO T PERFORM MAINTENANCE OR CLEANING OF THE EXTRACTOR WITHOUT FIRST SWIT CHING OFF THE ELECTRICIT Y SUPPL Y . Cleaning Y ou should use a nonabrasive cleaner . Any abrasive cleaner (including Cif ) will scratch the surface and could erase the control panel markings.
5 Fig . 3 Care and Maintenanc e Changing the charcoal lter (r e -circulating only) When the display ashes alternating the speed selected with the letter F , the charcoal lters must be replac ed.
6 Changing the Light DO NOT CHANGE THE LIGHT BULB IMMEDIA TEL Y AFTER USE AS THE BULB WILL BE HOT . ALLOW IT TO C OOL BEFORE REMOVING IT . Using a at blade screwdriv er , carefully prise o the lamp cover as shown in gure 4. Remove the bulb and replac e with a 12V 20W halogen light bulb.
7 DOUBLE POLE SWITCHED FUSE SPUR OUTLET USE A 3 AMP FUSE Mains Electr icity Connection THIS APPLIANCE MUST BE CONNECTED T O THE MAINS SUPPL Y BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSE SPUR OUTLET AND PROTECTED BY A 3A FUSE.
8 Electrical I nformation Mains electrical voltage: 230 – 240V ac, 50Hz T otal rated power consumption: 330W T roubleshooting If your extractor is not working: 1. Check that the mains supply has not been switched o . 2. Check that the fuse in the spur has not blown.
9 Mounting your Extractor IMPORT ANT : The extractor is intended to be mounted directly to the ceiling using xings appropriate for the ceiling . Ensure that there is adequat e ceiling strength and supports at the xing points; if in doubt, consult a joiner or electrician.
10 Installation Note: We r ecommend that you seek the help of another individual when installing this product. Preparing the extractor The electronic control bo x and ventilation pipe need to be tted to the motor body bef ore proceeding with the install.
11 Installation Assembling the extractor ready for mounting: 1. Place the extractor body on a table and x the support sec tions (D) using the supplied screws (E) as shown in g 11 below . 2. Remove the screws(A ) fastening the lower and upper(B) support sections as shown in g 12 below .
12 Installation Assembling the extractor ready for mounting: 4. Assemble the upper (B) and lower (C) support sections at the desired height (as calculated in step 3) using the supplied scr ews (G) as shown in g 13.
13 Installation Mounting the extractor to the ceiling: 1. Using the supplied template , drill four holes in the ceiling and t suitable wall plugs into the holes, if required . Note that plugs may not be required if the extractor is to be mounted directly to the ceiling joists.
14 Installation Mounting the extractor to the ceiling: 4. Recirculating mode: If the extractor is to be used as a recirculation device, ltering the air before recycling into the kitchen then the vent diverter needs to be tted. Fit the div erter(M) to the upper suppor t section using screw (I) and connect the ventilation pipe (H).
15 DOUBLE POLE SWITCHED FUSE SPUR OUTLET USE A 3 AMP FUSE Mains Electr icity Connection THIS APPLIANCE MUST BE CONNECTED T O THE MAINS SUPPL Y BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSE SPUR OUTLET AND PROTECTED BY A 3A FUSE.
16 NO TES:.
17 NO TES:.
18 NO TES:.
19 E & O E. All instructions, dimensions and illustrations are provided for guidance only . CD A reserve the right to change specifications without prior notice. Attribute Symbol Value Units Model Identification evpk90 Annual Energy Consumption AEC Hood 134.
20 Customer Care Department • The Group Ltd. • Harb y Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www.cda.eu Passionate about style T o contact our Customer Car e Depar tment, or for Service, please contact us on the details below .
An important point after buying a device CDA EVPK90 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought CDA EVPK90 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data CDA EVPK90 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, CDA EVPK90 you will learn all the available features of the product, as well as information on its operation. The information that you get CDA EVPK90 will certainly help you make a decision on the purchase.
If you already are a holder of CDA EVPK90, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime CDA EVPK90.
However, one of the most important roles played by the user manual is to help in solving problems with CDA EVPK90. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device CDA EVPK90 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
