Instruction/ maintenance manual of the product ECP72 CDA
Go to page of 20
Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .
2 Important The CD A Group L td cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CD A reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment.
3 safety (L VD) and Electromagnetic interference compatibility (EMC). IMPORT ANT INFORMA TION FOR CORRECT DISPOSAL OF THE PRODUCT IN A CCORD ANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer providing appliance recycling services.
4 • This extractor has been designed to be used in a room with a volume of less than 36m. • Steam cleaners must not be used when cleaning this appliance.
5 Using your Extractor For best performance, you should switch on the extractor 15 minutes before starting to cook and leave it to run for appro ximately 15 minutes after the end of cooking. Control Panel A - Power o button B - Speed level buttons C - Light button T o switch the extractor light on or o • Press button “C” .
6 Care and Maintenance IMPORT ANT : DO NOT PERFORM MAINTENANCE OR CLEANING OF THE EXTRA CT OR WITHOUT FIRST SWIT CHING OFF THE ELECTRICITY SUPPL Y . Cleaning Y ou should use a nonabrasive cleaner . Any abrasive cleaner (including Cif ) will scratch the surface and could erase the control panel markings.
7 prevent damage from other items in the dishwasher . T o remove the grease filter , push in the button on the handle and then pull down on the filter at the front as shown in figure 2. When you have released it at the front, then you can pull the filter out completely .
8 Fig. 3 C D Model Lightbulbs required ECP/ECN 12V G4 type Changing the Light IMPORT ANT : DO NO T PERFORM MAINTENANCE OR CLEANING OF THE EXTRA CT OR WITHOUT FIRST SWIT CHING OFF THE ELECTRICITY SUPPL Y . DO NO T CHANGE THE LIGHT BULB IMMEDIA TEL Y AFTER USE AS THE BULB WILL BE HO T .
9 Model Lightbulbs required ECP/ECN 12V G4 type Bulb replacement is not covered by the guarantee. Only use bulbs recommended for your extractor . Do not fit bulbs of a higher power rating. Bulbs of a lower power rating may be adequate for use, generally last longer and use less energy .
10 correspond with the coloured markings identifying the terminals connecting to the fuse spur , proceed as follows: • The wire which is coloured green and yellow must be connected to the terminal marked E (Earth) or coloured green. • The wire which is coloured blue must be connected to the terminal marked N (Neutral) or coloured black.
11 Electrical Information Mains electrical voltage: 230 – 240V ac T otal rated power consumption: 140W T roubleshooting Please note: Y our extractor is equipped with a motor protection device that will switch o the motor to prevent damage from overheating.
12 Mounting your Extractor When the extractor is to be installed above an electric hob, the minimum distance between the hob and extractor must ex ceed 600mm (650mm is recommended). When the extractor is to be installed above a gas hob, the minimum distance between the hob and extractor must ex ceed 700mm (750mm is recommended).
13 IN THE ABSENCE OF ANY INSTRUCTIONS SUPPLIED WITH THE GAS HOB, THE MINIMUM DIS T ANCE BETWEEN THE HOB AND EXTRA CT OR MUST BE A T LEAS T 760mm. The width of any hob must not be greater than the width of the extractor installed above it.
14 Fig. 5 Figu re 2 - M ar k wal l a s r eq ui re d ( s ee ta bl e 1) Fig. 7 Figu re 3 - D ri l l h o l es Fig. 9 Fig. 10 Figu re 5 - Se c ur e hoo d ( t igh t en a ll scr ews) Figu re 6 - Fi t d uc t.
15 Fig. 12 Fig. 13 Fig. 14 Mount upper and lower chimney brackets Fix ducting (seal joint) Figu re 7 - Mo u n t ch im ne y b ra c ke ts Figu re 8 - F i x d uc t ing (s ea l j o in t) Figu re 9 - Mo u nt t h e c h im ne y Figu re 10 - Adj u st an d s e c u re t h e ch im ne y Mount the chimney Adjust and secure the chimney Fig.
16.
17.
18.
19 E & O E. All instructions, dimensions and illustrations are provided for guidance only . CDA reserve the right to change specifications without prior notice. Attribute Symbol Units Model Identification ecn62/72/92 ecp62/72/82 ecp92/102/112 Annual Energy Consumption AEC Hood 84.
Please contact our Customer Care Department, or for Service on the details below . Customer Care Department • The Group Ltd. • Harby R oad • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer .care@cda.eu W : www.
An important point after buying a device CDA ECP72 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought CDA ECP72 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data CDA ECP72 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, CDA ECP72 you will learn all the available features of the product, as well as information on its operation. The information that you get CDA ECP72 will certainly help you make a decision on the purchase.
If you already are a holder of CDA ECP72, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime CDA ECP72.
However, one of the most important roles played by the user manual is to help in solving problems with CDA ECP72. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device CDA ECP72 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
