Instruction/ maintenance manual of the product CI830 CDA
Go to page of 28
.
.
4 5 6 10 20 22 25 WARNINGS SPECIFICA TIONS INST ALLA TION AND ASSEMBL Y USING THE APPLIANCE. PRACTICAL TIPS MAINTENANCE AND CLEANING SAFETY AND TROUBLESHOOTING ENVIRONMENT AL WARNINGS washing machine .
4 war nings This washing machine comes with a manual that includes operating, maintenance and installation instructions. Please read all the instructions before using the washing machine.
Power cord Control panel Detergent dispenser Stainless steel drum Accessible filter 5 washing machine W ater inlet hose. specifications ACCESSORIES Drain hose Hatch Adjustable feet.
6 washing machine a Remove the screws holding the plastic covers to the back of the washing machine. b Loosen and remove the 3 blocking screws. c Cover the holes with the plastic covers you have just removed. installation and assembly Do not throw the blocking scr ews away .
7 CONNECTION TO THE MAINS W A TER SUPPL Y AND DRAINAGE The water supply hose is inside the drum: a Connect the bent end of the hose to the threaded inlet of the electr ovalve located at the rear of the washing machine. b Connect the other end of the hose to the water intake.
Important Use the adjustable feet to level the washing machine. This will reduce the noise level and prevent it fr om moving during use. Do not bring the feet too far out, you will achieve better stability . Y ou need to use a spanner for the models that have a nut.
PRE-CLEANING When your washing machine has been correctly installed, we r ecommend that you pre-clean the machine. This is to check that the installation, the connections and the drainage are all corr.
10 washing machine a Sort the clothes according to fabric and how they are made: We r ecommend using the delicate programmes for sensitive fabrics. Ther e is a special wool programme for woollens. b Sort clothes according to how soiled they are. • W ash lightly soiled garments using a short programme.
a Y our washing machine ’ s detergent dispenser has three compartments. b Put the detergent or additive into the detergent dispenser before starting the wash programme. c Liquid detergents may also be used in this washing machine. The level of liquid must never be higher than the MAX mark printed on the dispenser wall.
12 3 SELECTING THE W ASH PROGRAMME using the appliance and practical tips The procedur e for selecting the wash programme is as follows: a Activate the programme selector by pressing it to r elease it. b Select the wash programme by turning the programme selector dial (see programme table).
13 using the appliance and practical tips eco-note We r ecommend you choose a wash programme without pr ewash whenever possible. This will save you money and help protect the envir onment.
Cotton/Linen delicate colours very light soil Cotton/Linen whites/colours very light soil Cotton/Linen delicate colours light soil Cotton/Linen fast colours light soil Cotton/Linen fast colour medium .
15 0,15/46 0,20/30 0,40/49 0,65/49 1,02/49 1,90/55 1,45/60 0,15/55 0,30/55 0,60/55 0,95/50 0,50/60 0,05/25 0,05/0 0,00/0 60 30 82 91 80 120 105 55 55 60 70 40 23 10 2 _ _ NOTE: the KWh and litre consumptions and programme durations may vary depending on the type and amount of clothes, mains water pressure, etc.
16 4 SPIN SPEED SELECTION using the appliance and practical tips SPIN-DR YING The wash options must always be selected after choosing the wash programme. Any programme change during selection cancels the previously selected options. a Spin speed selection and anti-crease button The selected programme has its own particular spin speed.
17 using the appliance and practical tips Delay time selection button A delay of up to 24 hours can be selected. The delay must be selected after choosing the wash programme. T o select the hours of delay , press the clock button. Each time the button is pressed the start of washing is delayed by 1 more hour .
18 Start/Stop button a T o start up the washing machine you have to press the Start/Stop button . The minutes remaining until the end of washing and drying will appear on the display at all times.
PROGRAMME PHASES 19 When the programme is running, the programme phase and the time r emaining for it to end will appear on the display .. The active phases will appear successively at the top of the display as the programme progr esses. The time remaining until the end of the programme will also appear on the display .
20 washing machine maintenance and cleaning After each wash, leave the door open for a while to allow the air to circulate freely inside the machine. From time to time, depending on the hardness of your water , it is recommendable to run a full wash cycle using a decalcifying product.
CLEANING THE ACCESSIBLE FIL TER AND THE OUTSIDE maintenance and cleaning T o avoid burns, do not carry out this operation when the wash water is at a temperature of over 30 º C. When there have been spillages of detergent or additives from the dispenser onto the washing machine cabinet, clean them up right away as they are corr osive.
washing machine safety and tr oubleshooting 22 Important If you detect any problems with your washing machine, you will probably be able to r ectify them yourself by consulting the following instructions. If this is not the case, unplug the appliance and contact CDA CUSTOMER CARE.
safety and tr oubleshooting 23 Why doesn ’ t the washing machine take in water? Why doesn ’ t the washing machine drain or spin-dry? Why doesn ’ t the washing machine spin-dry? Why can ’ t I see any water in the drum during the wash? If no water is entering, F01 will appear on the display .
24 safety and tr oubleshooting Why is there still some water in the dispenser? Why can ’ t I open the hatch immediately after the wash has finished? Other indications This may be because the dispenser needs cleaning. This simple operation is described in Maintaining and cleaning the appliance.
When your appliance is of no further use, it should not be disposed of together with general domestic waste. It can be taken, free of charge, to a specific waste collection centre, run by your local authority , or dealers who provide this service.
.
.
04/07 LJ6A030Q9.
An important point after buying a device CDA CI830 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought CDA CI830 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data CDA CI830 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, CDA CI830 you will learn all the available features of the product, as well as information on its operation. The information that you get CDA CI830 will certainly help you make a decision on the purchase.
If you already are a holder of CDA CI830, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime CDA CI830.
However, one of the most important roles played by the user manual is to help in solving problems with CDA CI830. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device CDA CI830 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
