Instruction/ maintenance manual of the product 50AH024-096 Carrier
Go to page of 20
Manufacturer reserves the right to disco ntinue, or change at any time, specifications or de signs without notice and without inc urring obligations. Catalog No . 04-53500057-0 1 Printed in U. S.A. F orm 50AH-14SI Pg 1 5-10 Replaces: 50AH-12SI Installation, Star t-Up , and Ser vice Instructions CONTENTS SAFETY CONSIDERA T IONS .
2 Evaporator Confi g uration Factory-In s talled Option s 50AH AC 04 8 5 – – – – 2 1 XX 50AH – Horizont a l, Indoor S ingle-P a ck a ge Cooling Unit Packa g in g 1 – Dome s tic 2 – Expor.
3 DET AIL A CLEARANCE HOLE FOR 3 /8" HANGING ROD TYP 8 PL S AIR IN COIL ACCE SS FRONT TOP RIGHT REAR LEFT RETURN AIR S UPPL Y AIR AIR OUT MOT OR ACCE SS ELECT BO X ACCE SS BLOWER ACCE SS EV AP S .
4 64 1/2 6 1/ 8 1 83 /4 1 3 /4 16 1/ 8 1 1/2 3 1 3 /16 1 15/16 44 1/ 8 3 7/ 8 38 1/ 8 6 1/16 24 3 /4 38 1/2 5 15/16 3 1/4 3 1/4 5 7/ 8 1 3 5/ 8 9 5/16 12 3 / 8 6 7/16 2 1/4 5 7/ 8 12 0 lb s . Fig. 3 — Unit Dimensions — 50AH024-060 Units wi th F actory-Instal led Air -Side Economizer a50-8548 NO TES: 1.
5 DET AIL A CLEARANCE HOLE FOR 3 /8" HANGING ROD TYP 8 PL S DET AIL "A" AIR IN MOT OR ACC ELECT BOX ACCE SS COIL ACCE SS COMPRE SS OR ACCE SS FIL TER ACCE SS CONDEN S A TE DRAIN 7/8&quo.
6 1 3 7/16 16 1/16 6 7/16 1 8 3 /4 6 5/ 8 70 1/2 3 1/4 2 1/4 5 7/ 8 22 1/ 8 21 7/16 1 8 15/16 10 7/ 8 3 1/4 5 15/16 1 1/2 72 1/2 1 15/16 61 1/ 8 3 7/ 8 4 3 1/ 8 6 1/16 42 1/2 29 3 /4 12 NO TES: 1. Dimensions are in inches. 2. Economizer weight is 200 l b s.
7 Table 1 — Physical Data LEGEND * Shipping weigh ts include b ase unit plus packag ing. †If componen ts are to b e split, addi tional refrigera nt will b e needed.
8 Table 1 — Ph ysical Data (cont) LEGEND * Shipping weigh ts include b ase unit plus packag ing. †If componen ts are to b e split, addi tional refrigera nt will b e needed.
9 Condensing section must be located in same plane as, or above, evaporator section to main tain the liquid refrigerant seal at the expansion device. This permits expansion device to feed liquid refrigerant to evaporator coil properly . T o split sections (some of the following steps may be eliminated depending on particular application): 1.
10 of the tubing. Use a 1 / 4 -in. hole to mount the valve. Clean and debur the tubing before doing any brazing to ensure that no chips or debris are left in the refrigerant circuit. Remove the Schrader valve cap and core before doing any brazing. 5. After brazing the tubing to the self-sealing coupling halves, evacuate each line to 500 microns.
11 Table 2B — Electrica l Data — Upgrade 1 Evapora tor Motor with Standar d Condenser Motor Table 2C — Electrica l Data — Upgrade 2 Evapora tor Motor with Standar d Condenser Motor LEGEND UNIT.
12 Table 2D — Electrical Data — Upgra de 3 Evaporator Motor with Sta ndard Condenser Motor Table 2E — Electric al Data — Standard Evaporator Moto r with Upgrade 1 Condenser Motor LEGEND UNIT 5.
13 Table 2F — Elect rical Data — Upg rade 1 Eva porator Motor with Upgr ade 1 Condenser Motor Table 2G — Electric al Data — Upgrade 2 Evapo rator Motor with Upgrade 1 Condenser Motor LEGEND UN.
14 Table 2H — Electrical Data — Upg rade 3 Ev aporator Mo tor with Upg rade 1 Con denser Moto r Table 2I — Electrica l Data — Standard Evapo rator Motor with Upgrade 2 Condenser Motor LEGEND U.
15 Table 2J — Electrical Data — Upgrade 1 Eva porator Motor with Upgrade 2 Condense r Motor Table 2K — Electrical Data — Upg rade 2 Evap orator Mot or with Upgr ade 2 Conde nser Motor LEGEND U.
16 Table 2L — Elect rical Data — Upgrad e 3 Evaporator Moto r with Upgrade 2 Cond enser Motor LEGEND Table 3 — Evaporator-Fan Performa nce LEGEND NO TES: 1. Refer to T a b le 1 f or ev aporator f an motor and dr ive inf ormation. 2. Upgrade 1 Static Motor is required for boldface valu es.
17 Table 4 — Co ndenser-Fan Performance LEGEND NO TES: 1. Refer to T a b le 1 f or condenser fan motor and drive inf or mation. 2. Upgrade 1 Static Motor is required for boldface valu es.
18 Blower Belt Adjustment — Inspect blower belt for wear , proper belt tension, and pulley alignment as conditions require or at the beginning of each heating and air conditioning season. Make sure that fan shafts and motor shafts are parallel and level.
.
Manufacturer reserves the right to disco ntinue, or change at any time, specificatio ns or designs without notice and without inc urring obligations. Catalog No .
An important point after buying a device Carrier 50AH024-096 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Carrier 50AH024-096 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Carrier 50AH024-096 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Carrier 50AH024-096 you will learn all the available features of the product, as well as information on its operation. The information that you get Carrier 50AH024-096 will certainly help you make a decision on the purchase.
If you already are a holder of Carrier 50AH024-096, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Carrier 50AH024-096.
However, one of the most important roles played by the user manual is to help in solving problems with Carrier 50AH024-096. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Carrier 50AH024-096 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
