Instruction/ maintenance manual of the product 502 D AEG
Go to page of 16
502 D Extractor Hood Installation and Operating Instructions.
3 Contents Electrical connections .......................................................... 4 Safety w ar nings f or electricians .............................................. 4 Appliances with 2 wires ...............................................
4 It must be ensured that the voltage and current indicated on the rating plate agree with the voltage of the user to electricity supply. If the appliance has been equipped with a mains lead with a moulded-on type plug, the following regulations must be comply with: The plug moulded on to the lead incorporates a fuse.
5 The appliance must be connected to fix ed wir ing with a double pole s witched fused spur outlet with or without pilot lamp . W e strongly recommend the appliance to be connected only b y a qualified electrician who is a member of the NICEIC who will comply with the IEE and an y local regulations.
6 When the unit is used in its extractor version, a sufficiently large ventilation hole must be provided, with dimensions that are approximately the same as the outlet hole. The air outlet must not be connected to chimney flues or combus- tion gas ducts.
7 When used as an extractor unit, the hood must be fitted with a 100mm diameter hose. If the fumes must be forced out through the wall, you must obtain a MKZ sizable wall exhaust pipe (with external exhaust and air intake), E-Nr.- 610 899 004 (Ø 120 mm) which is one of our optional parts.
8 Cooking vapours are cleaned by the charcoal filter (Special accessories) and ducted back into the kitchen. The AEG original KF-Plus charcoal filter is necessary for the recirculating mode (see paragraph “Special accessories”). For the recirculating mode proceed as follows: a) Remove the grid by turning knob A (fig.
9 Description of the appliance 1) Light switch 2) Motor switch 3) Work surface lamp 4) Grid 4 3 Technical details Model 502 D Net weight: 5 kg Height 145 mm Width 520 mm Depth 285 mm Absorbed power: 1.
10 After having adjusted the hood for the version required, it may be installed. This appliance is designed for fitting in a cabinet or some other support. The opening to be made on the bottom of the wall-hung cabinet must correspond with the measurements shown in fig.
11 The hood is fitted with one variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on a for approximately 5-15 minutes after having finished, thus ensuring that all that cooking odours are eliminated.
12 Hood Operation A B The hood is fitted with a variable speed motor. The most effective use of the hood is obtained by switching it on a few minutes before you start cooking and leaving it on a for approximately 15 minutes after you have finished, thus ensuring all cooking odours are eliminated.
13 Before performing any maintenance operation, disconnect the hood from the electricity. The hood has a metal grease filter. To clean the filter, proceed as follows: Open the grill by turning knob A (fig. 2). Pull the two plastic stops B as shown by the arrows (fig.
14 The charcoal filter must be changed at least every 4 months. The charcoal filter cannot be washed or regenerated. The hood can only work well in the recirculating mode if the AEG recommended filter has been used, the filter is changed as recommended in this section and if the hood is cleaned and maintained as instructed in this booklet.
15 Always turn off the electricity before replacing lamps! 1) Remove the grid (Fig. 2) in order to check the lamps and replace them if necessary. 2) Unscrew the lamps that do not work and replace them with 40W max lamps (E14). If the light does not function, check that the lamps are properly screwed before contacting a customers’ service centre.
16 See AEG price-list for wallbox and hose accessories. KF-Plus charcoal filter E-Nr. 942 118 620 Technical assistance service You are welcome to telephone our technical assistance service (see list of technical assistance centres) whenever you need information or in the unlikely event of a fault.
AEG Hausgeräte AG Postfach 1036 D-90327 Nürnberg © Copyright by AEG H 259 226 140 L 650A.
An important point after buying a device AEG 502 D (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought AEG 502 D yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data AEG 502 D - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, AEG 502 D you will learn all the available features of the product, as well as information on its operation. The information that you get AEG 502 D will certainly help you make a decision on the purchase.
If you already are a holder of AEG 502 D, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime AEG 502 D.
However, one of the most important roles played by the user manual is to help in solving problems with AEG 502 D. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device AEG 502 D along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
