Instruction/ maintenance manual of the product MG6320 Canon
Go to page of 25
PIXMA MG6300 Setup Guide © CANON INC. 2012 series.
Setup Guide This guide provides information for setting up a network connection for the printer . Network Connection Wireless Connection Preparation for Connection Printer Setup Setup Procedure Select.
Network Connection W ireless Connection a Preparation for Connection Before Starting Wireless Connection Setup 1. Make sure that the printer is turned on.
2. Flick the screen left or right, then tap the WLAN setup icon. The (blue) Wi-Fi lamp (A) lights up when wireless connection is enabled. c Setup Procedure Selection The printer will automatically search for access points supporting WPS (Wi-Fi Protected Setup).
d -A Push Button Method d Connection Using WPS 1. Press and hold the WPS button on the access point. For details on pressing the WPS button, refer to the access point manual. 2. T ap Start setup on the printer within 2 minutes. The (blue) Wi-Fi lamp on the printer fl ashes while searching for or connecting to the access point.
d -B Standar d setup d Connection via Standard setup 1. T ap Standard setup. 2. T ap your access point. 3. One of the screens below will be displayed on the printer . 4. T ap the screen. 5. Enter the network password (WEP key or passphrase). Character entry is case-sensitive.
d -C WPS d Connection Using WPS 1. T ap WPS. 2. T ap Push button method. 3. T ap OK. 4. Press and hold the WPS button on the access point. For details on pressing the WPS button, refer to the access point manual. 5. T ap OK on the printer within 2 minutes.
d -D Other setup (Advanced setup) d Connection via Advanced setup 1. T ap Other setup. 2. T ap Advanced setup. 3. T ap your access point. 4. T ap the security protocol used by the access point. Disable 5. When the left screen appears, tap OK. The network connection setup is now complete.
WEP 5. T ap the WEP key number you want to use. 6. T ap the screen. 7. Enter the WEP key . Character entry is case-sensitive. 8. T ap Apply . 9. Make sure that the WEP key is correct. 10. T ap OK. 1 1. When the left screen appears, tap OK. The network connection setup is now complete.
WP A/WP A2 5. T ap the screen. 6. Enter the passphrase. Character entry is case-sensitive. 7. T ap Apply . 8. Make sure that the passphrase is correct. 9. T ap OK. 10. When the left screen appears, tap OK. The network connection setup is now complete.
W ired Connection a Preparation for Connection Before Starting Wired Connection Setup 1. Make sure that the printer is turned on. If the power is on, the POWER lamp (A) will be lit. Notes on Wired Connection Make sure that the computer and router (A) (or access point) are connected.
c Printer Setup 1. If the HOME button (A) on the printer is lit, touch the HOME button. 2. Flick the screen left or right, then tap Setup. 3. Flick the screen up or down, then tap Device settings. 4. T ap LAN settings. 5. T ap Change wireless/wired. 6.
Character Entr y Y ou can enter the characters when the keyboard is displayed on the printer . Follow the procedure below . 1. Y ou can enter the characters when the keyboard is displayed on the printer's LCD. Password entry is case sensitive. : T ap to switch between "lower case letters" and "numbers and symbols.
T roubleshooting Standar d setup The T arget Access Point is Not Detected Is the network device (router , etc.) turned on? If the network device is already turned on, turn it off, then turn it back on. Check the access point name/network name and network password of your access point or router .
When using multiple access points: T ap Use multiple AccessPoints. An Unknown Access Point is Displayed Access points in use nearby may also be detected. The Access Point Name is Not Displayed Properly Access point names with double-byte characters are not displayed properly .
WEP Failed to connect to the access point. Make sure that the WEP key entered for the access point is correct. In addition, when using WEP key number 2, 3 or 4 of the access point, set to use WEP key number 1, or select a WEP key number by entering wireless connection settings of the printer directly .
WP A/WP A2 Failed to connect to the access point. Make sure that the passphrase entered for the access point is correct. If the problem is not resolved, there may be other causes. See also the sections below: If the DHCP function of the access point is inactive, enable the DHCP function and confi gure wireless connection settings again.
T o perform Standard setup again 1. T ouch the HOME button (A). 2. Flick the screen left or right, then tap the WLAN setup icon. .
WPS Cannot connect. Connections are being attempted from multiple access points simultaneously . The screen appears when connections are being attempted from multiple access points simultaneously . W ait for a while, then confi gure WPS settings again.
Advanced setup The T arget Access Point is Not Detected Is the network device (router , etc.) turned on? If the network device is already turned on, turn it off, then turn it back on. Check the access point name/network name and network password of your access point or router .
When using multiple access points: T ap Use multiple AccessPoints. An Unknown Access Point is Displayed Access points in use nearby may also be detected. The Access Point Name is Not Displayed Properly Access point names with double-byte characters are not displayed properly .
WEP Failed to connect to the access point. Make sure that the WEP key entered for the access point is correct. In addition, when using WEP key number 2, 3 or 4 of the access point, set to use WEP key number 1, or select a WEP key number by entering wireless connection settings of the printer directly .
The device may not be able to connect to the network in the following cases: If the DHCP function of the access point is inactive, enable the DHCP function or specify the IP address (IPv4 only) of the printer and confi gure wireless connection settings again.
WP A/WP A2 Failed to connect to the access point. Make sure that the passphrase entered for the access point is correct. If the problem is not resolved, there may be other causes. See also the sections below: If the DHCP function of the access point is inactive, enable the DHCP function and confi gure wireless connection settings again.
T o perform Advanced setup again 1. T ouch the HOME button (A). 2. Flick the screen left or right, then tap the WLAN setup icon. .
An important point after buying a device Canon MG6320 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Canon MG6320 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Canon MG6320 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Canon MG6320 you will learn all the available features of the product, as well as information on its operation. The information that you get Canon MG6320 will certainly help you make a decision on the purchase.
If you already are a holder of Canon MG6320, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Canon MG6320.
However, one of the most important roles played by the user manual is to help in solving problems with Canon MG6320. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Canon MG6320 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
