Instruction/ maintenance manual of the product LV-8320 Canon
Go to page of 81
MUL TIMEDIA PROJECT OR User ’ s M anu al.
2 Features and Design This Multimedia Projector is designed with the most advanced technology for portability , durability , and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology .
3 Each name of corporations or products in this book is either a registered trademark or a trademark of its respective corporation. Features and Design ..............
4 .
5 All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain th em for late r use.
6 Immediately turn the power off, unplug the projector , and contact your dealer under the following conditions, otherwise a fire or an electric shock may result. – If smoke comes out from it.
7 – Remove the batteries when they have been exhausted or not in use for an extended period of time. – Be sure to replace both batteries at the same time.
8 Openings in the cabinet are provided for ventilation. T o ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. Hot air is exhausted from the exhaust vent.
9 The AC Power C ord suppl ied with this projector meets the requirement for use in t he countr y you purchased it.
10 ⑭ ⑦ ⑩ ⑨ ⑥ ⑪ ⑬ ⑫ ⑧ ⑮ ① .
11 ③ ④ ① ⑤ ⑥ ⑪ ⑦ ⑨ ⑧ ⑩ ⑥ Connect the S-VIDEO output signal from video equipment to this jack (p.
12 ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑨ Lights yellow when the projection lamp reaches its end of life (pp.
13 T o ensure safe operation, please observe the following precautions: – Do not bend, drop or expose the remote controller to moisture or heat.
14 T o ensure safe operation, please observe the following precautions : ● Use two (2) AAA type batteries. ● Always replace batteries in sets. ● Do not use a new battery with a used battery .
15 For projector positioning, see the figures below . The projector should be set perpendicularly to the plane of the screen.
16 • VGA Cables (Mini D-sub 15 pin) * • Audio Cables • HDMI-DVI cable (*One cable is supplied; other cables are not supplied with the projector .
17 .
18 • When the AUDIO OUT is plugged-in, the projector's built-in speaker is not available.
19 Th is p r oj ec t or u se s no m in al i n pu t vo lt a ge s of 100 -24 0 V A C an d it a uto mat ica lly s ele cts t he correct input voltage.
20 The preparation display will disappear after 30 seconds. (See page 56 for Lamp mode status.) Connect the projector ’s AC power cord into an AC outlet. The POWER indicator lights red.
21 PIN (Personal Identification Number) code is a security code that allows the person who knows it to op erate t he pro jecto r . S ettin g a PIN co de prevents unauthorized use of the projector .
22 .
23 T h e p r o j e c t o r c a n b e a d j u s t e d o r s e t v i a t h e O n - S c r e e n M e n u .
24 Main Menu For detailed functions of each menu, see “Menu T ree” on pages 70-72. Main Menu ③ For both of comp.
25 Rotate the Zoom Ring to zoom in and out. Rotate the Focus Ring to adjust the focus of the image.
26 1 2 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select . Press the Point ► button or the OK button to access the submenu items. Press the VOLUME+/– buttons on the top control or on the remote controller to adjust the volume.
27 Using the remote controller for some frequently used operations is advisable.
28 Press the P-TIMER button on the remote controller to operate the Count up/Count down function. Refer to p.54 for detail of Setting for the P-timer function. T o stop the count time, press the P-TIMER button.
29 Choose either or by pressing the COMPUTER 1 or COMPUTER 2 button on the remote controller .
30 This projector automatically tunes to various types of computers with its Multi-scan system and Auto PC Adjustment.
31 Auto PC Adjustment function is provided to automatically adjust , .
32 Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector .
33 T o store the adjusted data, select and then press the Point ► button or the OK button. Move the highlight to one of the Mode 1 to 10 in which you want to store, and then press the OK button.
34 .
35 Reset Press the MENU button to display the On-Screen Menu.
36 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to select and then press the Point ► button or the OK button.
37 Select . The On-Screen Menu disappears and appears. Press the OK button to expand the image size.
38 Choose VIDEO or by pressing the INPUT button on the top control, or the VIDEO or the S-VIDEO button on the remote controller . Before using these buttons, correct input source should be selected through menu operation as described below .
39 Choose or by pressing the COMPONENT or the COMPUTER 1 button on the remote controller .
40 1 .
41 .
42 1 2 Press the Point ◄ button to decrease the contrast, press the Point ► button to increase the contrast (from 0 to 63). Press the Point ◄ button to decrease the brightness, press the Point ► button to increase the brightness (from 0 to 63).
43 An interlaced video signal can be displayed in progressive mode. Select one of the following options. ........ Disabled. L 1 ........ For an active picture. L 2 ........ For a still picture.
44 This projector has the picture screen resize function, which enables you to customize the image size. 1 2 Provide the image to fit the screen size while maintaining the aspect ratio of the input signal.
45 This function is used to adjust keystone distortion of the projected image. Use the Point ▲▼ buttons to choose the item you want to adjust. T o correct keystone distortion, press the OK button.
46 Press the MENU button to display the On-Screen Menu. Press the Point ▲▼ buttons to select and press the Point ► button or the OK button to access the submenu items.
47 • During is in progress, If the MENU button or the POWER button is pressed, will stop.
48 This function decides whether to display On-Screen Displays. On ........................ Show all the On-Screen displays. Use this function when you want to project images after the lamp becomes bright enough. The factory default setting is in this option.
49 This function enables you to capture an image being projected to use it for a starting-up display or interval of presentations. Select and press the OK button.
50 Use the Point ▲▼ buttons to enter a number . Press the Point ◄► buttons to fix the number and move the red frame pointer to the next box. The number changes to .
51 The COMPUTER IN 2/MONITOR OUT terminal on the back of the projector is switchable for computer input or monitor output (p.
52 Select the Picture in Pictrue mode among P in P , and .
53 T ime left before Lamp is off. For reducing power consumption as well as maintaining the lamp life, the Power management mode function turns off the projection lamp when the projector is not operated for a certain period.
54 This function is available when operating the projector via network. .. Supply the power to the network function even after turning off the projector by pressing the POWER button on the remote controller .
55 Closed caption is a printed version of the program sound or other information displayed on the screen. If the input signal contains closed captions, you can turn on the feature and switch the channels.
56 This projector provides two different remote control codes: the factory-set initial code ( ) and the secondary code ( ).
57 .
58 Use the Point ▲▼ buttons to select , On 1 or On 2 , and then press the OK button to make a choice. Use the Point ▲▼ b u t t on s t o e n t e r a n u m b e r.
59 Choose the running speed of cooling fans from the following options according to the ground elevation under which you use the projector . ................ Normal speed. Set this function to when using the projector in non- high altitude environment.
60 This function returns all setting values except for the , , .
61 The Information Menu is used for checking the status of the image signal being projected and the operation of the projector .
62 The W ARNING indicator shows the state of the function which protects the projector . Check the state of the W ARNING indicator and the POWER indicator to take proper maintenance.
63 .
64 Unplug the AC power cord before cleaning.
65 When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and LAMP REPLACE indicator lights yellow .
66 T h is p r o j e c t o r u s e s a h i g h -p r e s s u r e l a m p w h i c h mu s t b e h a n d l e d c a r e f ul l y a n d properly . Improper handling may result in accidents, injury , or create a fire hazard.
67 – Solutions – Plug the power cord of the projector into the AC outlet. – See if the POWER indicator lights red.
68 – Check the connection between your computer or video equipment and the projector . See pages 16-18. – See if the input signal is correctly output from your computer . Some laptop computers may need to change the setting for monitor output when connecting to a projector .
69 – Check menu or menu and adjust them.
70 Menu T ree V olume Mute On/Of f 0-63 ANAL.
71 Auto 1080i 1035i 720p 575p 480p 575i 480i 0–63 0–63 Off (2) Auto P AL SECAM NTSC NTSC 4.
72 Check the indicators for projector condition. • • • green • • • red • • • off • • • blinks green. When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow . When this indicator lights yellow , replace the projection lamp with a new one promptly .
73 Basically this projector can accept the signal from all computers with the V -, H-Frequency mentioned below and less than 140 MHz of Dot Clock.
74 • The specifications are subject to change without notice. • Depending on your PC settings, the digital signals of your PC may not be projected correctly . In such a case, confirm your PC settings. • When you project a DVI signal, connect the cables, turn the projector on, then select the input.
75 Projector T ype Multi-media Projector Dimensions (W x H x D) 13.
76 Model No. L V -CA32 .
77 This projector is compliant with PJLink Standard Class 1 of JBMIA (Japan Business Machine and Information System Industries Association). This projector supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1.
78 .
79 Put the label below (supplied) on in a prominent place of the projector's body while it is locked with a PIN code. While the projector is locked with the PIN code.
80 Unit: mm(inch) Screw Holes for Ceiling Mount Screw: M4 Depth: 12.0(0.47) 67.9 (2.67) 212.4 (8.36) 216.5 (8.52) 350 (13.78) 176.3 (6.94) 79.7 (3.14) 254.4 (10.02) 256.0 (10.08) 91.4 (3.60) 109.
1 CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan U.S.A. CANON U.S.A. INC. One Canon Plaza, Lake Success, NY 11042-1198, U.S.A. For all inquires concerni ng this product, call toll free in the U.S. 1-800-OK-CANON CANADA CANON CANADA INC.
An important point after buying a device Canon LV-8320 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Canon LV-8320 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Canon LV-8320 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Canon LV-8320 you will learn all the available features of the product, as well as information on its operation. The information that you get Canon LV-8320 will certainly help you make a decision on the purchase.
If you already are a holder of Canon LV-8320, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Canon LV-8320.
However, one of the most important roles played by the user manual is to help in solving problems with Canon LV-8320. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Canon LV-8320 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
