Instruction/ maintenance manual of the product MM801 AEC
Go to page of 12
Installation Guide 1 MM801 8.4" LCD OVERHEAD MONITOR I nstallation G uide POW ER ME NU/ ENT ER ON OFF A UTO.
Installation Guide 2 Import ant Notice An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation.
Installation Guide 3 MA TERIALS INCLUDED IN THIS P ACKAGE: 1) MM801 Video Monitor (P/N 136D3649) – 1pc 2) T rim Ring (P/N 102C4007) – 1pc 3) Remote Control (P/N : 136B3650) – 1pc 4) Hardware Pac.
Installation Guide 4 GENERAL INST ALLA TION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what component s, VCP , T uner , RF Modulator/external amp, remote headphones, DVD, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups.
Installation Guide 5 VEHICLE PREP ARA TION: 1) Locate an accessory power source (+12v when key is in the ACC. and run positions, and 0v when key is of f). Also locate a good ground wire. Generally , these wires can be found at the ignition switch or fuse-box.
Installation Guide 6 TRIM RING INST ALLA TION: This page only covers special installation considerations for the trim ring installation. If the video monitor is to be installed in a vehicle with the trim ring, it may need to be trimmed to fit the contour of the vehicle headliner .
Installation Guide 7 Roof Roof Support Headliner 5"x9"x3/4" Plywood Block (4) #8x1" self drilling screws T rim Ring Video Unit (4) #8 flat washers (4) #8x3/4" self tapping scr.
Installation Guide 8 1) Insert the Circular Mini-Din Connector of the source Component Harness through the wire tie loop on the main PCB and into the Mini-Din Connector on the main PCB. 2) Pull the wire tie loop tight and cut off the excess. 3) Connect the Power Harness to the mating connector on the Video Monitor .
Installation Guide 9 Red / black - Lamp on Black / red - Lamp common Violet / brown - Lamp Auto T o 3 pin connector on Monitor To constant +12vdc To constant +12vdc Factory Door ajar switch or Body Co.
Installation Guide 10 T roubleshooting: SYMPT OM: No power at Video Monitor Power but no video or sound Picture, but no sound REMEDY : -V erify +12 VDC on Red wire at 2 pin Power Harness behind video monitor .
Installation Guide 11 This Page Intentionally Left Blank.
© Copyright 2004 AEC 150 Marcus Blvd. Hauppauge, NY 1 1788 128-7036.
An important point after buying a device AEC MM801 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought AEC MM801 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data AEC MM801 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, AEC MM801 you will learn all the available features of the product, as well as information on its operation. The information that you get AEC MM801 will certainly help you make a decision on the purchase.
If you already are a holder of AEC MM801, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime AEC MM801.
However, one of the most important roles played by the user manual is to help in solving problems with AEC MM801. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device AEC MM801 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
