Instruction/ maintenance manual of the product LAKE-TROLL Cannon
Go to page of 16
OWNER’S MANU AL NOTE: Do not return your CANNON® Do wnrigger to your retailer. Your retailer is not authorized t o repair or replace this unit. You may obtain service b y: • calling CANNON® at 1.
2 Parts Description 1. Reel This is used to spool the cable, available in length s ranging from 150 to 400 feet. 2. Boom This is used to extend the weight out from the body of the downrigger and has a pulley fixed to its end. Boom lengths range from 24 to 53 inches.
3 Downrigger Mounting on Boats A downrigger should be mounted where ever it is easy to operate and observe. You want to be able to see your fishing rod and to react quickly. So, choosing a good spot to mount your downrigger on your boat is 99% of the job.
4 Side Rail Mounting Side/Rail mounts can be mounted to a welded T-section. It can also be used at the two rail section butt joint. In both installations it is recommended to use a non-slip material, such as rubber or a thin wood sheet, between metal surfaces.
5 MOUNTING & SETUP Outboard Facing Note Locking Slots in Base Side or Gunwale Decks up to 7/16" Thick Base Wellnuts Decks Thicker T han 7/16" Base Rear or Stern Stern Facing Washer, Lock.
6 MOUNTING & SETUP Deck Up to 7/16" Thick Base Deck Thicker Than 7/16" Wellnut Cannon Deck Plate Low-Profile Swivel Base Washers, Scre w s, & Nuts Latch Decks thinner than 1/4" Use a Cannon Deck Plate to prevent deflection and add stability to decks thinner than 1/4".
7 Setting Up Y our Downrigger Attaching the Boom The boom inserts into the downrigger frame. Be sure that the boom is held securely by seating it firmly against the shoulder inside the fame and fastening the boom locking screw (#8 X 1” self tapping) so that it engages the hole in the boom.
8 Att aching the Crank Handle Assembly Make sure the thrust bearing is sandwiched between its two races. The thrust bearing spring should be oriented where the narrow end is toward the bearing. Slide the bearing with races and spring over the ratchet shaft.
9 Cannon Uni-Release The Cannon Uni-Release attaches directly to the downrigger weight. Attach fishing line to the clip at the end of the release, and then click through a series of increasing tension settings. The release can be used with any test line on salt or fresh water and may be adjusted from 2 to 22 pounds of grip tension on the line.
10 ATTACHING THE ROD HOLDER Recommended Area to Clamp Rod Holder Star Washer Placement Angled Shoulder Dual Rod Holder Assembly Single Rod Holder Assembly Att aching the Rod Holder The positive lock rod holder incorporates a locking disk that allows the rod holder to be aligned in 15 degree increments.
11 OPERATING YOUR DOWNRIGGER To Lower Weight To Raise Weight Operating Y our Downrigger After mounting the Cannon downrigger to your boat, release some line from your rod and reel so that the lure is anywhere from 5 to 100 feet behind the boat, this is called drop back.
12 Blowback Simply stated, blowback is what happens to the downrigger weight when you pull it through the water behind your boat. As your speed increases, so does the horizontal distance between the weight and your downrigger. The faster you go, the farther the weight is behind you.
13 Adjusting the Depth Meter The Cannon Depth Meter provides non-slip accuracy, plus easy resetting. To reset, just slide the meter away from the reel until the gears are disengaged. Spin meter gear to change setting. NOTE: Actual fishing depth may vary from depth shown on meter due to trolling speed and weight of cannon ball.
14 T en Good T r olling T ip s 1) Test your lures over the boat side before sending them down and back. Do this to make sure the lure wiggles and wobbles properly without going belly up or wandering off. Some lures can be adjusted, fine tuned actually, to impart maximum action.
15 LIMITED WARRANTY & SERVICE POLICY CANNON® LIMITED W ARRANTY Johnson Outdoors Inc. warrants to the original purchaser that if the accompanying product (see ex clusions below) proves to be defective in material or workmans hip within the following warranty periods, Johnson Outdoors Inc.
16 All CANNON Downriggers are covered by US Pat.D-269, 9 92. Co pyright 2006 Johnson Outdoors, Inc. All rights reserved. Conforms to 89/336/EEC (EMC) under standa rds EN 55022A, EN 50082-2 since 1996 LN V9677264 WA RN ING : This product contains chemic al(s) known to the state of California to cause cancer and/or r eproductive toxicity.
An important point after buying a device Cannon LAKE-TROLL (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cannon LAKE-TROLL yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cannon LAKE-TROLL - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cannon LAKE-TROLL you will learn all the available features of the product, as well as information on its operation. The information that you get Cannon LAKE-TROLL will certainly help you make a decision on the purchase.
If you already are a holder of Cannon LAKE-TROLL, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cannon LAKE-TROLL.
However, one of the most important roles played by the user manual is to help in solving problems with Cannon LAKE-TROLL. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cannon LAKE-TROLL along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
