Instruction/ maintenance manual of the product AL2710 Campbell Hausfeld
Go to page of 28
Airless Paint Systems Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.
2 Operating Instructions and Parts Manual Airless Paint Systems Description Airless paint sprayers are capable of spraying a wide variety of latex, oil- based, and alkyd paints, as well as stains, preservatives and other non- abrasive finishes.
Airless Paint Systems 3 Operating Instructions and Parts Manual General Safety Information (Cont.) 4. Do not smoke or eat when spraying paint, insecticides, or other flammable substances. 5. Always work in a clean environment. To avoid injury and damage to the workpiece, do not aim the spray gun at any dust or debris.
4 Operating Instructions and Parts Manual Airless Paint Systems General Safety Information (Cont.) ● Do not use pliers to tighten or loosen high pressure connections. ● Motor is equipped with an automatic thermal overload. Motor will restart without warning, after cooling.
Airless Paint Systems 5 Operating Instructions and Parts Manual Pr e-Operation (Cont.) is no pressure in the unit, and close the prime/pressure relief valve for storage. Never leave pump unattended while it is under pressure! 6. START UP AFTER STORAGE: Before using water-base paint, flush with soapy water and then a clean water flush.
6 Operating Instructions and Parts Manual Airless Paint Systems www.chpower.com Pr e-Operation (Cont.) NOTE: Do not use thread sealer on swivel unions as they are made to self- seal. Use thread seal on tapered male threads only. 2. Fill the Packing Nut/Wet Cup 1/3 full with Throat Seal Oil (TSO) supplied (see Figure 7).
7 Airless Paint Systems Operating Instructions and Parts Manual www.chpower.com Quadraflow TM Tip for painting (12" from surface) Fan Width (in.) (mm) .
8 Operating Instructions and Parts Manual Airless Paint Systems www.chpower.com Operation (Cont.) SPRAY TECHNIQUE Good Spray Gun Technique is at the core of any spray paint operation. Operator skill and efficiency is as important as good equipment and good paint.
9 Airless Paint Systems Operating Instructions and Parts Manual www.chpower.com Electrical System (Cont.) assembly (board) and is installed on the "P-ZR" terminals. If you are "Zero Calibrating" a pressure control assembly presently in the unit, remove jumper from single terminal P-ZR and place on both terminals P-ZR.
10 Operating Instructions and Parts Manual Airless Paint Systems www.chpower.com Electrical System (Cont.) REPLACEMENT OF ELECTRICAL COMPONENTS NOTE: Refer to Electrical System Diagram (page 20) and LCD Diagram (page 22). PRESSURE CONTROL ASSEMBLY (ELECTRICAL CONTROL BOARD) 1.
11 Airless Paint Systems Operating Instructions and Parts Manual www.chpower.com Service (Cont.) with a wrench since this could result in breaking the shaft.
12 Operating Instructions and Parts Manual Airless Paint Systems www.chpower.com Service (Cont.) Replace worn or damaged parts. 6. If gear grease needs replacing, replace with gear grease (Part No. 331-132) 7. Clean mating surfaces of cover and box thoroughly.
13 Airless Paint Systems Operating Instructions and Parts Manual www.chpower.com Maintenance (Cont.) 5. Place a 1/4” allen wrench into insert and unscrew insert from piston. Clean piston and seat, and then inspect them carefully for wear and damage.
Operating Instructions and Parts Manual Airless Paint Systems 14 www.chpower.com Unit does not prime Unit primes, but has no pressure or poor pressure Unit does not maintain good spraying pressure Unit does not run 1. Air leak due to: a. Loose suction nut.
15 Airless Paint Systems Operating Instructions and Parts Manual www.chpower.com Control Settings Fuse Power Source Thermal Overload Pressure Control Assembly (Board) Motor Sensor Pressure Control Kno.
Operating Instructions and Parts Manual 16 www.chpower.com AL2710 Spray Gun 2 1 3 4 5 6 7 9 9a 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 AL2710 For Replacement Parts, Call 1-800-626-4401 Plea.
Operating Instructions and Parts Manual 17 www.chpower.com AL2710 AL2710 Spray Gun Ref. No. Description Part Number Qty. 1 Rev-guard AL2245 1 2* Rev-tip AL22xx 1 3 Rev-tip seal-metal 561-025 1 4 Rev-t.
Operating Instructions and Parts Manual 18 www.chpower.com AL2710 4 5 6, 7, 8, & 9 21 23 22 18 20 24 25 19 17 16 15 14 12 10 13 1 2 11 3 Airless Paint Sprayer Model AL2710 33 27 28 29 30 31 32.
Operating Instructions and Parts Manual 19 www.chpower.com AL2710 AL2710 Airless Paint Sprayer Ref. No. Description Part Number Qty. 1 Pail hook 331-336 1 2 Screw 100-390 2 3 Cover 331-234 1 4 Frame 331-273 1 5 Motor cover 331-199 1 6 0.
Operating Instructions and Parts Manual 20 www.chpower.com AL2710 Electrical System.
Operating Instructions and Parts Manual 21 www.chpower.com AL2710 Ref. No. Description Part Number Qty. 1 Electrical power cord 331-168 1 2 Strain relief 331-185 1 3 Screw 331-138 1 4 Toggle switch 331-311 1 5 Fuse 20A Slow Blow 331-328 1 6 Fuse holder 331-312 1 7 0.
Operating Instructions and Parts Manual 22 www.chpower.com AL2710 LCD Display 1 2 3 4 5 6 7 Ref. No. Description Part Number Qty. 1 Screw 100-362 4 2 Mylar Label-Clear 101-270 1 3 Window 331-360 1 4 S.
Operating Instructions and Parts Manual 23 www.chpower.com AL2710 Manifold Filter Part No. 111-200-99 1 2 3 4 5 6 7 8 9 10 8 111-200-99 Ref. No. Description Part Number Qty.
Operating Instructions and Parts Manual 24 www.chpower.com AL2710 Gearbox Sleeve Bearing Replacement 1 2 3 Ref. No. Description Part Number Qty. 1 Sleeve bearing 331-061 1 2 Washers 331-103 2 3 Screws 331-197 2 NOTE: When replacing item 1, cover the outside of the sleeve with clear silicone prior to inserting into cover assembly.
Operating Instructions and Parts Manual 25 www.chpower.com AL2710 Ref. No. Description Part Number Qty. 1 Pump body 331-011 1 2 Retainer 331-029 1 3 Ball 1/2” Diameter 331-030 1 4 O-ring Teflon 106-.
Operating Instructions and Parts Manual 26 www.chpower.com Ref. No. Description Part Number Qty. 1 Cover 331-234 1 2 Bearing 331-046 1 3 Crosshead assembly 331-038 1 4 Gear crank 331-407 1 5 Bearing 3.
Operating Instructions and Parts Manual 27 www.chpower.com 331-236 Ref. No. Description Part Number Qty. - Packing kit 331-210 1 1 Packing nut 331-037 1 2 Seal holder 331-019 1 3* O-ring Viton-Black 1.
28 Operating Instructions and Parts Manual www.chpower.com Limited Warranty 1. DURATION: From the date of purchase by the original purchaser as follows: Standard Duty Paint Application Systems and all Paint Application Accessories - 1 year, Serious Duty Paint Application Systems - 3 years, Extreme Duty Paint Application Systems - 5 years.
An important point after buying a device Campbell Hausfeld AL2710 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Campbell Hausfeld AL2710 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Campbell Hausfeld AL2710 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Campbell Hausfeld AL2710 you will learn all the available features of the product, as well as information on its operation. The information that you get Campbell Hausfeld AL2710 will certainly help you make a decision on the purchase.
If you already are a holder of Campbell Hausfeld AL2710, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Campbell Hausfeld AL2710.
However, one of the most important roles played by the user manual is to help in solving problems with Campbell Hausfeld AL2710. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Campbell Hausfeld AL2710 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
