Instruction/ maintenance manual of the product RCD272DBTi Caliber
Go to page of 18
RCD 2 7 2 B T i manual • GB •.
RCD 2 7 2 B T i manual 3 PANEL CONTROLS 1. - Power / Mute 2. - Previous / next track - Seek + / - (long press) 3. - SRC - TUNER - Disc play (when disc inserted) - USB (when USB connected) - AUX - BLUETOOTH(when BT connected) - iPod (when iPod connected) 4.
RCD 2 7 2 B T i manual 4 OTHER INSTRUCTIONS Press the button to open the panel. 1. SD/MMC card slot 2. Disc eject 3. Reset hole Note: Pressing the RESET hole will erase the clock setting and stored stations. 4. Panel status indicator Lights up when you ip the panel down; Twinkles when you remove the panel.
RCD 2 7 2 B T i manual 5 RADIO OPERATIONS Select tuner as playing source Press [SRC] button once or more to enter RADIO mode. Selecting the radio band Press the [ BAND / ] button on the panel to select one radio band among FM1, FM2, FM3, AM. Manual tuning During manual tuning, the frequency will be changed in steps.
RCD 2 7 2 B T i manual 6 Radio Data System This unit has a built-in “Radio Data System” decoder system that supports broadcast stations transmitting “Radio Data System” data. When using the “Radio Data System” function, always set the radio to FM mode.
RCD 2 7 2 B T i manual 7 CD/MP3/WMA OPERATIONS This unit can playback MP3/WMA les Notes: • If yo u pla y a WMA file with active DRM (Digital Rights Management), there will be no audio .
RCD 2 7 2 B T i manual 8 track advances ahead to the beginning of the next track. 3. For MP3/WMA disc, press and hold the [ 6 ] button (1 sec.) to move ahead to +10 tracks. Track-down 1. Press the [ ] button to move back to the beginning of the current track.
RCD 2 7 2 B T i manual 9 Repeat play This function allows you to play the current track repeatedly or play a track currently being played in the MP3/WMA folder repeatedly. CD: 1. Press the [ 3 ] button once or more until “ RPT ON ” appears on the LCD to perform repeat play.
RCD 2 7 2 B T i manual 10 Press the [ EQ ] button to enter sound effect setting mode. First press shows current EQ. Rotate the knob to changes DSP EQ in this order: OFF -> POP -> ROCK -> CLAS.
RCD 2 7 2 B T i manual 11 iPod & iPhone OPERATIONS Connect Connect an iPod or iPhone to the USB connector. When connecting a device, the unit will read the les automatically.
RCD 2 7 2 B T i manual 12 BLUETOOTH OPERATIONS The Bluetooth allows you to utilize your car’s built-in audio system for wireless mobile phone or music handsfree communication. Some Bluetooth mobile phones have the audio features, and some portable audio players support Bluetooth feature.
RCD 2 7 2 B T i manual 13 Note: • Some mobile phones may not be able to transfer data of Phonebook. • TransferCall You can switch Handsfree call and mobile phone call. Press the [ BAND / ] button during call. • Answeringacall You can answer an incoming call by pressing the [BAND / ] button.
RCD 2 7 2 B T i manual 14 In any mode, press and hold [ DISP ] button to enter system setup. Press [ ] or [ ] button to select options, rotate the [ V OLU M E] knob to adjust. CLOCK Press the [V OLU M E] knob, time display blinks. Press [ ] or [ ] to c hoose hour or minute .
RCD 2 7 2 B T i manual 15 ELECTRICAL CONNECTIONS Wiring Diagram MIC SWC Light Orange.
RCD 2 7 2 B T i manual 16 INSTALLATION GUIDE Installation Opening This unit can be installed in any dashboard having an opening as shown below. The dashboard should be 4.75mm - 5.56mm thick in order to be able to support the unit. If the opening is too small, carefully cut or le as necessary until the sleeve easily slides into the opening.
RCD 2 7 2 B T i manual 17 TROUBLESHOOTING The following checklist can help you solve some problems which you may encounter when using the unit. Before consulting it, check the connections and follow the instructions in the user manual.
RCD 2 7 2 B T i manual 18 SPECIFICATION General Power supply: 12V DC (11V-16V) Test voltage 14.4V, negative ground Maximum power output: 75Wx4 channels Continuous power output: 20Wx4 channels (4 ,10% T.H.D.) Suitable speaker impedance: 4-8 ohm Pre-Amp output voltage: 2.
WWW .CaliBER.nl CaliBER HEaD OffiCE • The Netherlands • Fax: +31 (0)416 69 90 01 • E-mail: info@caliber .nl.
An important point after buying a device Caliber RCD272DBTi (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Caliber RCD272DBTi yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Caliber RCD272DBTi - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Caliber RCD272DBTi you will learn all the available features of the product, as well as information on its operation. The information that you get Caliber RCD272DBTi will certainly help you make a decision on the purchase.
If you already are a holder of Caliber RCD272DBTi, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Caliber RCD272DBTi.
However, one of the most important roles played by the user manual is to help in solving problems with Caliber RCD272DBTi. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Caliber RCD272DBTi along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
