Instruction/ maintenance manual of the product RCD264 Caliber
Go to page of 18
.
Page CONTENTS 01 Contents 02 Installation 04 Using the detachable front panel 05 Wiring iagram 06 Operations 06 07 General perations 0 Radio perations CD/MP3 perations 1 Mixed- CD perations 1 USB pera.
Notes: - Choose the mounting location where the unit will not interfere with the normal driving function of the driver . - Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly .
7. Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables. 8. Slide the unit into the sleeve until it locks into place. 9. T o further secure the unit, use the supplied metal strap to secure the back of the unit in place.
If your vehicle is a Nissan, T oyota, follow this mounting instruction. Use the screw holes marked T (T oyota), N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle. Fasten the unit to the factory radio mounting brackets.
Wiring diagram L R 15 ISO CONNECT OR ISO connector: Part A: A1: A2: A3: A4: A5: A6: A7: A8: Part B: B1: B2: B3: B4: B5: B6: B7: B8: No Connect No Connect No Connect Battery B+ (Y ellow) Antenna (Blue).
Operations Location and function of controls Front panel: 27 28 (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (1 1) (12) (13) Power on/off Button ( ), Mute Button V olume Control, Audio/Menu Selector (SEL).
Reset the unit Power on/off 1.T urn off the unit power . 2. () - Rotate the volume control to adjust volume level. - Press the button short and repeatedly to select the volume, bass, treble, balance and fader.
“RETUNE L or RETUNE S” RETUNE L mode: - RETUNE S mode: “MASK DPI or MASK ALL”: - MASK DPI mode: MASK ALL mode: (long/short retune): This function allows you to set the duration after which the automatic search for traffic information or a station with an identical PI should be carried out.
CT -> FREQUENCY -> PTY NONE-> In CDP/USB/SD mode: CT -> FREQUENCY -> PTY NONE -> T rack or file number and Running time The selected information is displayed for 5 seconds, then the radio goes back to the first display mode after 5 seconds.
Short pressing the button, the radio searches for each preset station that saved in the memories of the current band. If the field strength level is more than the threshold level, the radio will hold .
Listening to Traffic Announcement The RDS data are the PI, PS, TP , PTY , T A and AF data. PI PS PTY TP TA AF (Program identification): Code for identifying the radio station. (Program service): Name of the radio station. (Program type): T ype of program such as news, Pop music, sports etc.
Repeat playback Shuffle playback Select the track or file for playback in MP3 or WMA format In CD or MP3/WMA file playback, briefly press the button to Press again to stop repeat playback and resume normal playback.
The unit is equipped with a USB port on the front panel of the unit, you can connect a USB stick through the USB port. When you insert a USB stick through the port, the unit will search the MP3 files and start to play it automatically . If insert a disc into the disc slot while read the file in the USB device, the unit will playing the disc first.
- Do not warp discs. - A disc should always be kept in its case when not in use to prevent from damage. - Do not place discs in the following places: 1. Direct sunlight. 2. Dirty , dusty and damp areas. 3. Near car heaters. 4. On the seats or dashboard.
T rouble shooting Symptom Cause Solution No power The car ignition switch have not turn on. If the power supply is connected to the car accessory circuits, but the engine is not moving, switch the ignition key to “ACC”. The fuse has been blown. Replace a new one.
1. GENERAL 2. CD PLA YER 3. RADIO FM Power Supply Requirements DC 12 V olts, Negative Ground Chassis Dimensions 178(W)x160(D)x 50(H) mm T one Controls -B a s s( a t1 0 0H z ) ± 1 0d B - T reble (at 10 kHz) ±10 dB Maximum Output Power 4x75 watts Current Drain 15 Ampere (max.
W W W . C A L I B E R . N L CALIBER HEAd OffICE • The Netherlands • Fax: +31 (0)416 69 90 01 • E-mail: info@caliber .nl.
An important point after buying a device Caliber RCD264 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Caliber RCD264 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Caliber RCD264 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Caliber RCD264 you will learn all the available features of the product, as well as information on its operation. The information that you get Caliber RCD264 will certainly help you make a decision on the purchase.
If you already are a holder of Caliber RCD264, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Caliber RCD264.
However, one of the most important roles played by the user manual is to help in solving problems with Caliber RCD264. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Caliber RCD264 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
