Instruction/ maintenance manual of the product RCD110B Caliber
Go to page of 17
CAR CD/MP3 PLA YER / RDS RECEIVER WITH USB INTERF ACE , SD INTERF ACE AU X U S B IN T 2 6 5 RD M 4 RP T 3 OP EN M EN U MO D E ID3 DI S P 1 BA N D PS PT Y AS M UT E 1. P ANEL RELEASE BUT TON 2. ENCODER VOLUME KNOB 3. SYSTEM MENU BUTTON 4. PRESET MEMORY BUTTONS 5.
E - 1 1. HANDLING COMP ACT DISCS MOISTURE CONDENSA TION NOTES ON CDs P . 2 P . 3 P . 4 P . 1 P . 5 P . 6 P . 7 1. 2. 3. 4. 5. NOTES ON DISCS There are paste residue. Ink is sticky (P .5). Stickers that are beginning to peel away , leaving a sticky residue (P .
2. INST ALLA TION 30° DIN FRONT/REAR-MOUNT - DIN FRONT -MOUNT (Method A) Installation the unit 1. Dashboard 2. Half Sleeve 3. Screw 1 7 4 2 3 5 6 1. Dashboard 2.
- DIN REAR-MOUNT (METHOD B) Installation using the screw holes on the sides of the unit. Fastening the unit to the factory radio mounting bracket. 1. Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned (are fitted) and tighten the screws at 2 places on each side.
E - 4 3. DET ACHABLE CONTROL P ANEL(D.C.P) 1. T o attach the front panel back to the unit chassis, firstly join the left guide block hole to the left cylinder ( ), then join the right guide block hole and the right cylinder ( ). T o remove the front panel: 1.
4. WIRING DIAGRAM E - 5 CONNECTOR ISO 1 2 1 2 3 4 7 5 6 8 7 5 3 8 6 4 CONNECTOR B Figure 2 CONNECTOR A ISO CONNECTOR WIRING CHART YELLOW WIRE COLOR VIOLET/BLACK GREY/BLACK GREEN/BLACK WHITE/BLACK VIOL.
Press this button to fold down the front panel. press POWER/MUTE button or any other button on the front of the radio (except Open / Eject) to turn the unit on.
6. AUDIO / MENU OPERA TIONS 3) AUDIO MENU ( MENU ) Press “ MENU ” button to access the Audio Menu. User can navigate thru the Audio Menu intems by pressing the MENU button. Once the desired menu item appears on the display , adjust that option by using the encoder volume knod within 5 seconds.
7. RADIO OPERA TIONS 11) RADIO SIGNAL STRENGTH METER (RSLM) This is use to indicate the signal strength of current radio station broadcast. When you choose RADIO mode, it will show on the display . 4) ST A TION PRESET BUTTONS (M1-M6) 1.Press these buttons briefly to recall the stored stations in the selected band.
8) PTY BUTTON Each time when this button is pressed, the PTY mode will toggle in the following order: PTY Music Group -> PTY Speech Group ->PTY Off Music Group Speech Group M1 POP , ROCK NEW.
M3) REPEA T BUTTON (RPT) Press this button, the current track will be played repeatedly until this button is pressed again. 12) EJECT BUTTON ( ) Press this button to eject the CD from the unit.
10. USB DRIVE OPERA TIONS ST AR T THE USB DEVICE MODE 2. Plug in the USB drive / device completely as indicated in picture 2 (P .2) and display will show “USB PLA Y” to indicate that the USB drive / device is being plugged in correctly & the download has begun.
Open button 11. SD OPERA TIONS 1.Press panel open button to release the front panel.(P .1) 3.The SD card slot is located on the unit as indicated in (P .4). 4. Insert the SD card into the card slot in the correct direction until a “CLICK” sound is heard.
Notes : L OADING DISC NAVIGA TING THROUGH DIRECTORIES AND TRACKS Insert the CD as usual, if it is an MP3 CD , the display will show “MP3 T01” then the message “READING” will appear , when disc scanning completed, the first track on the first directory will play .
(2) SEARCH DIRECTORY / TRACK NAME BY USING ENCODER VOLUME KNOB Under MP3 Play Mode, press AS/PS BUT TON twice, the display shows “ * “. Rotate the ENCODER VOLUME KNOB for selecting the character . In this Encoder Search mode, SELECT button use as move cursor .
E - 16 GENERAL Power Supply Polarity Speaker impedance Power Output Frequency Range Intermediate Frequency Usable Sensitivity Stereo Separation S/N Ratio DC 11 -14V Negative Ground 4 ohms 40W x 4 87.5-108 MHz 10.7 MHz Better than 15dB at S/N 30 dB 25 dB at 1KHz 50 dB 13.
14. TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer .
An important point after buying a device Caliber RCD110B (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Caliber RCD110B yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Caliber RCD110B - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Caliber RCD110B you will learn all the available features of the product, as well as information on its operation. The information that you get Caliber RCD110B will certainly help you make a decision on the purchase.
If you already are a holder of Caliber RCD110B, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Caliber RCD110B.
However, one of the most important roles played by the user manual is to help in solving problems with Caliber RCD110B. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Caliber RCD110B along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
