Instruction/ maintenance manual of the product RCD 266 Caliber
Go to page of 10
.
EN-2 LOCA TION OF P ARTS AND CONTROLS 1. POWER ON/OFF ( ) 2. FUNCTION SELECT BUTT ON: BASS/TREBLE/BALANCE/F ADER / T A SEEK/PI SOUND/ RETUNE/MASK DPI/EON/BEEP/T A VOL/ADJ TIME/AUDIO DSP (SEL) 3. VOL UP/VOL DOWN FOR BASS/TREBLE/BALANCE/F ADER 4. PRESET ST A TIONS (1,2,3,4,5,6) 5.
EN-3 53mm 182mm 3 2 182 mm 53m m 1 2 1 3 4 Bend these claws, if necessay release screw and bracket ISO CONNECTOR RCA Jack Line Out: Red (right) White (left) CONNECTOR A 4. MEMORY +12V 5. AUTO ANTENNA OUTPUT 7. +12V (TO IGNITION KEY) 8. GROUND Note: (connector A no.
EN-4 10 7 1 2 3 4 4 4 5 5 6 6 8 9 Dashboard TO SUPPORT THE UNIT Detaching and attaching the front panel The front panel of this unit can be detached in order to prevent the unit from being stolen. FOLDING DOWN AND DET ACHING/A TT ACHING THE FRONT P ANEL Before detaching the front panel, be sure to press the button (1) OFF rst.
EN-5 OPERA TION INSTRUCTIONS 1. POWER ON/OFF ( ) By pressing this key , the unit is on and off. This unit is turned on by pressing any key . 2. FUNCTION SELECT BUTTON: BASS/TREBLE/BALANCE/F ADER / T A.
EN-6 EON MODE (2) When press the SEL button for more than 2 seconds, it is activated as selecting mode of these function. When the EON function is switched on the radio switches to traf c radio or PTY groups if the T A or PTY function has been activated.
EN-7 USING THE RDS FUNCTION What is RDS? The RDS (Radio Data System) is a digital information system developed by the EBU (European Broadcast Union). Piggy-backed on normal FM broadcasts, RDS offers a variety of information services and automatic retuning functions for RDS-compatible car stereos.
EN-8 14. MUTE BUTT ON ( ) Press this button to mute the sound at once. Press again to return to previous volume level. 15. LCD DISPLA Y The Liquid Crystal Display will display the current state of the unit. 16. OPEN THE FRONT P ANEL Press button and the front panel will open.
EN-9 • Press “VOL” knob longer than 2 sec. • The song which has same character you selected is displayed. • With “VOL VOL VOL / VOL VOL VOL ” knob, you can select the song you want. • Press “VOL” knob, then the song you selected will start.
EN-10 TECHNICAL SPECIFICA TIONS CD/MP3/WMA PLA YER SECTION Signal to Noise Ratio > 60 dB Channel Separation > 50 dB (1kHz) Frequency Response 20 Hz - 20 kHz TUNER FM Frequency Range 87.5-108 MHz Intermediate Frequency 10.7 MHz Sensitivity 2.8 µV Stereo Separation 30 dB Signal to Noise Ratio 50 dB Channel Step 50 kHz LINE-OUT Output 1.
An important point after buying a device Caliber RCD 266 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Caliber RCD 266 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Caliber RCD 266 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Caliber RCD 266 you will learn all the available features of the product, as well as information on its operation. The information that you get Caliber RCD 266 will certainly help you make a decision on the purchase.
If you already are a holder of Caliber RCD 266, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Caliber RCD 266.
However, one of the most important roles played by the user manual is to help in solving problems with Caliber RCD 266. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Caliber RCD 266 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
