Instruction/ maintenance manual of the product MCD 165 Caliber
Go to page of 18
INSTR UCTION MANU AL C AR CD/MP3 PLA YER / RDS RECEIVER MCD 165.
BAND 1 2 3 4 5 6 DISP This unit is equipped with the most advanced “TOUCH SENSE P ANEL ” which is easy and convenient to use. And here is some tips on how to use this touch sense panel: Tips The pressing or activating of each button actually all you need is a very light touch, even not really necessary to “PRES S” it.
E - 2 1. HANDLING COMP ACT DISCS MOISTURE CONDENSA TION NOTES ON CDs P . 2 P . 3 P . 4 P . 1 P . 5 P . 6 P . 7 1. 2. 3. 4. 5. NOTES ON DISCS There are paste residue. Ink is sticky (P .5). Stickers that are beginning to peel away , leaving a sticky residue (P .
2. INST ALLA TION Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and system work properly . Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
DIN REAR-MOUNT (METHOD B) Installation using the screw holes on the sides of the unit. Fastening the unit to the factory radio mounting bracket. 1. Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned (are fitted) and tighten the screws at 2 places on each side.
3. DET ACHABLE CONTROL P ANEL (D .C.P .) Removing The Detachable Control Panel (D.C.P .). 1. T urn the power off 2. Press the D .C.P . release button 3. Remove the D .C.P . P ANEL RELEASE BUTTON B A 2 Attaching the DCP CAUTION 1. Attach the panel at the right side first, with point B on the main unit touching point A on the D .
4. WIRING DIAGRAM AMP CONNECTOR ISO FEMALE WITH MALE TERMINAL ISO CONNECTOR 4 PIN+8 PIN 1 1 2 3 7 5 7 5 3 8 6 4 2 4 6 8 (See Figure 1) Figure 1 ISO CONNECTOR WIRING CHART GROUND POWER ANTENNA BATTERY(.
Press this button to remove the control panel. 5. BASIC OPERA TIONS 1) P ANEL RELEASE BUT TON (REL) 11) DISP BUTTON(DISP) 13) POWER ON/OFF BUTTON ( ) Press the POWER button on the front of the unit to turn on the unit. Long press the POWER button to turn Off the unit.
6. MENU OPERA TIONS TIME SET (CLK) The time on the clock is set to “12:00” by default, Rotate the encoder volume knob to adjust the minutes and hours.Press AUDIO/MENU button to select the hour or minutes. Note: Time format can not to set up, it should be follow the tunner area to change, when is in U .
7. RADIO OPERA TIONS 9) RADIO SIGNAL STRENGTH METER (RSLM) This is use to indicate the signal strength of current radio station broadcast. When you choose RADIO mode, it will show on the display . 7) ST ATION PRESET BUTTONS (M1-M6) 1.Press these buttons briefly to recall the stored stations in the selected band.
17)T A BUT TON When pressed short, it is activated as T A mode on or off When T A mode is on and traffic announcement is transmittude - When the unit is in CD mode, it will switch to radio mode temporarily . - If the volume lever was under the threshold point, it will be raised to the threshold point.
OVERVIEW OF THE RDS FUNCTION Radio Data System (RDS) is a broadcasting service that allows FM stations to send additional digital information along with the regular radio program signal.
PROGRAMMABLE OPTIONALS - T A SEEK , T A ALARM T o determine what action will the radio take if the newly tuned station does not receive TP information for 5 seconds. T A SEEK The radio retunes to a different station which contains TP information. T A ALARM The radio does not retune but beeps will come out.
9.CD OPERA TIONS 4) CD SL OT Insert the disc into CD slot. The CD will begin to play . M1) P AUSE BUTTON (P AU) Press this button to pause CD play , press again to release pause.
Notes : L OADING DISC NAVIGA TING THROUGH DIRECTORIES AND TRACKS Insert the CD as usual, if it is an MP3 CD , the display will show “MP3 T01” then the message “READING” will appear , when disc scanning completed, the first track on the first directory will play .
(2) SEARCH DIRECTORY / TRACK NAME B Y USING ENCODER VOLUME KNOB Under MP3 Play Mode, press MP3 MENU BUTTON twice, the display shows “ * “. Rotate the ENCODER VOLUME KNOB for selecting the character . In this Encoder Search mode, SELECT button use as move cursor .
GENERAL AM/MW Power Supply Polarity Speaker impedance Power Output Frequency Range Intermediate Frequency Usable Sensitivity Stereo Separation S/N Ratio DC 11 -14V Negative Ground 4 ohms 7 5W x 4 87.5-108 Mhz 10.7 MHz Better than 15dB at S/N 30 dB 25 dB at 1KHz 50 dB 11.
12.TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer .
An important point after buying a device Caliber MCD 165 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Caliber MCD 165 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Caliber MCD 165 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Caliber MCD 165 you will learn all the available features of the product, as well as information on its operation. The information that you get Caliber MCD 165 will certainly help you make a decision on the purchase.
If you already are a holder of Caliber MCD 165, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Caliber MCD 165.
However, one of the most important roles played by the user manual is to help in solving problems with Caliber MCD 165. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Caliber MCD 165 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
