Instruction/ maintenance manual of the product 2010 CTS-V Cadillac
Go to page of 464
2010 Cadillac CTS/CTS-V Owner Manual M Keys, Doors and Windows . . . 1-1 Keys and Locks . . . . . . . . . . . . . . . 1-2 Doors . . . . . . . . . . . . . . . . . . . . . . . . 1-17 V ehicle Security . . . . . . . . . . . . . . 1-23 Exterior Mirrors . .
2010 Cadillac CTS/CTS-V Owner Manual M V ehicle Care . . . . . . . . . . . . . . . . . . 9-1 General Information . . . . . . . . . . . . 9-2 V ehicle Checks . . . . . . . . . . . . . . . . 9-4 Headlamp Aiming . . . . . . . . . . . . 9-34 Bulb Replacement .
Introduction iii GENERAL MOTORS, GM, the GM Emblem, CADILLAC, the CADILLAC Crest and Wreath, and the name CTS/CTS-V are registered trademarks of General Motors.
iv Introduction Canadian V ehicle Owners Propriétaires Canadiens A French language copy of this manual can be obtained from your dealer/retailer or from: On peut obtenir un exemplaire de ce guide en français auprès du concessionnaire ou à l'adresse suivante: Helm, Incorporated P .
Introduction v V ehicle Symbol Chart Here are some additional symbols that may be found on the vehicle and what they mean. For more information on the symbol, refer to the index.
vi Introduction 2 NOTES.
Keys, Doors and Windows 1-1 Keys, Doors and Windows Keys and Locks K e y s .......................... 1 - 2 Remote Keyless Entry (RKE) System . . . . . . . . . . . . . . . . . . . . . . 1-4 Remote Keyless Entry (RKE) System Operation (Key Access) . . .
1-2 Keys, Doors and Windows Keys and Locks Keys { W ARNING Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move.
Keys, Doors and Windows 1-3 One of the following keys comes with the vehicle. This key is used for the driver door , ignition, and glove box. This key , located inside the keyless access transmitter , is used for the driver door , glove box, and rear seat pass-through door .
1-4 Keys, Doors and Windows Notice: If the transmitter does not have a button near the base, do not pull on the chrome base of the transmitter . This type of transmitter does not have a key inside. Pulling on the base of this transmitter could damage it.
Keys, Doors and Windows 1-5 Remote Keyless Entry (RKE) System Operation (Key Access) The Remote Keyless Entry (RKE) transmitter functions work up to 20 m (65 feet) away from the vehicle. There are other conditions that can affect the performance of the transmitter .
1-6 Keys, Doors and Windows The vehicle comes with two transmitters. Each transmitter will have a number on top of it, “ 1 ” or “ 2 ” . These numbers correspond to the driver of the vehicle. For example, the memory seat position for driver 1 will be recalled when using the transmitter labeled “ 1 ” , if enabled through the DIC.
Keys, Doors and Windows 1-7 Remote Keyless Entry (RKE) System Operation (Keyless Access) The Keyless Access System transmitter functions will work up to 60 m (195 feet) away from the vehicle.
1-8 Keys, Doors and Windows With Remote Start Shown, Without Similar Q (Lock): Press once to lock the doors. The turn signal indicators flash. When Q is pressed twice, the turn signal indicators flash twice, and the horn sounds once to confirm locking.
Keys, Doors and Windows 1-9 The vehicle comes with two transmitters. Each transmitter will have a number on top of it, “ 1 ” or “ 2 ” . These numbers correspond to the driver of the vehicle. For example, the memory seat position for driver 1 will be recalled when using the transmitter labeled “ 1 ” , if enabled through the DIC.
1-10 Keys, Doors and Windows 8. Press the ignition control knob to exit programming mode. 9. Remove the transmitter from the transmitter pocket and press K on the keyless access transmitter two times. 10. T o program additional transmitters, repeat Steps 6 through 9.
Keys, Doors and Windows 1-1 1 13. A beep sounds once programming is complete. The DIC displays Ready T o Learn Electronic Key # 2. T o program additional transmitters, insert each transmitter in the pocket until a beep is heard and the DIC advances to the next electronic key number .
1-12 Keys, Doors and Windows 3. Insert the new battery , positive side facing down. Replace with a CR2032 or equivalent battery . 4. Snap the transmitter back together . Remote V ehicle Start This vehicle may have a remote starting feature that allows you to start the engine from outside the vehicle.
Keys, Doors and Windows 1-13 Extending Engine Run Time T o extend the engine run time by 10 minutes, repeat Steps 1 and 2 while the engine is still running. The engine run time can only be extended if it is the first remote start since the vehicle has been driven.
1-14 Keys, Doors and Windows Door Locks { W ARNING Unlocked doors can be dangerous. . Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. The chance of being thrown out of the vehicle in a crash is increased if the doors are not locked.
Keys, Doors and Windows 1-15 Central Door Unlocking System The vehicle has a central door unlocking feature. When unlocking the driver door , the other doors can be unlocked by holding the key in the turned position for a few seconds or by quickly turning the key twice in the lock cylinder .
1-16 Keys, Doors and Windows Lockout Protection If the power door lock switch is pressed when the key is in the ignition and a door is open, all the doors will lock and only the driver door will unlock. If the doors are closed, they can be locked by using the Remote Keyless Entry (RKE) transmitter .
Keys, Doors and Windows 1-17 Doors T runk (Sedan) { W ARNING Exhaust gases can enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled.
1-18 Keys, Doors and Windows Press the button to open the trunk. Y ou can also press the button with the trunk symbol on the Remote Keyless Entry (RKE) transmitter to open the trunk.
Keys, Doors and Windows 1-19 Emergency T runk Release Handle (Sedan Only) Notice: Do not use the emergency trunk release handle as a tie-down or anchor point when securing items in the trunk as it could damage the handle.
1-20 Keys, Doors and Windows The switch is located on the driver ’ s door . The vehicle must be in P (Park) to use the power feature. The taillamps flash when the power liftgate moves. { W ARNING Y ou or others could be injured if caught in the path of the power liftgate.
Keys, Doors and Windows 1-21 . Press the power liftgate button on the center of the mode switch, located on the driver ’ s door . . Press the touchpad switch on the liftgate outside handle to open the liftgate. . Press and release the power liftgate button on the liftgate adjacent to the latch to close the liftgate.
1-22 Keys, Doors and Windows The vehicle has pinch sensors located on the side edges of the liftgate. If an object is caught between the liftgate and the body and presses against this sensor , the liftgate will reverse direction and open fully . The liftgate will remain open until it is activated again or closed manually .
Keys, Doors and Windows 1-23 V ehicle Security V ehicle theft is big business, especially in some cities. This vehicle has theft-deterrent features, however , they do not make it impossible to steal. Anti-Theft Alarm System This vehicle has an anti-theft alarm system.
1-24 Keys, Doors and Windows How to Detect a T amper Condition If K is pressed and the horn sounds, an attempted break-in has occurred while the system was armed. If the alarm has been activated, the Theft Attempted message will appear on the DIC. See Key and Lock Messages on page 4 ‑ 42 for additional information.
Keys, Doors and Windows 1-25 If the engine still does not start with the other key , the vehicle needs service. If the vehicle does start, the first key may be damaged. See your dealer/retailer who can service the theft-deterrent system and have a new key made.
1-26 Keys, Doors and Windows The system has one or more keyless access transmitters that are matched to an immobilizer control unit in your vehicle. Only a correctly matched keyless access transmitter will start the vehicle. If the keyless access transmitter is ever damaged, you may not be able to start your vehicle.
Keys, Doors and Windows 1-27 Power Mirrors Controls for the outside power mirrors are located on the driver door . T o adjust each mirrors: 1. Press } or | to select the driver or passenger side mirror . 2. Press one of the four arrows located on the control pad to move the mirror to the desired direction.
1-28 Keys, Doors and Windows Automatic Dimming Mirror Operation Automatic dimming reduces the glare of headlamps from behind you. The dimming feature comes on and the indicator light illuminates each time the vehicle is started. Cleaning the Mirror Do not spray glass cleaner directly on the mirror .
Keys, Doors and Windows 1-29 W ARNING (Continued) killed if caught in the path of a closing window . Do not leave keys in a vehicle with children. When there are children in the rear seat use the window lockout button to prevent unintentional operation of the windows.
1-30 Keys, Doors and Windows Express Window Anti-Pinch Override { W ARNING If express override is activated, the window will not reverse automatically . Y ou or others could be injured and the window could be damaged. Before you use express override, make sure that all people and obstructions are clear of the window path.
Keys, Doors and Windows 1-31 Sun Visors Swing down the visor to block out glare. It can also be detached from the center mount and moved to the side to block glare from that direction. The driver visor may also have buttons for a built-in garage door opener .
1-32 Keys, Doors and Windows The passenger side switch operates the sunroof. Express-Open: T o open the sunroof, fully press and release the rear of the passenger side switch. The sunroof will automatically open. T o stop the sunroof partway , press the switch a second time.
Seats and Restraints 2-1 Seats and Restraints Head Restraints Head Restraints . . . . . . . . . . . . . . . 2-2 Active Head Restraints . . . . . . . . 2-3 Front Seats Seat Adjustment . . . . . . . . . . . . . . 2-3 Power Seat Adjustment . . . . . . . 2-4 Lumbar Adjustment .
2-2 Seats and Restraints Head Restraints The vehicle's front seats have adjustable head restraints in the outboard seating positions. The vehicle's rear seats have head restraints in the outboard seating positions, but they are not adjustable.
Seats and Restraints 2-3 Active Head Restraints Active Head Restraint System The vehicle has an active head restraint system in the front seating positions. These automatically tilt forward to reduce the risk of neck injury if the vehicle is hit from behind.
2-4 Seats and Restraints Power Seat Adjustment Power Seats On vehicles with power seats, the controls are located on the outboard side of the seats. . Move the seat forward or rearward by sliding the horizontal control forward or rearward. . Raise or lower the front part of the seat cushion by moving the front of the horizontal control up or down.
Seats and Restraints 2-5 A single beep will sound. The seat, outside mirrors, and steering wheel will move to the position previously stored for the identified driver . If the Remote Keyless Entry (RKE) transmitter is used to enter the vehicle and the remote recall memory feature is on, automatic seat and mirror movement occur .
2-6 Seats and Restraints Lumbar Adjustment The vehicle may have this feature. The driver and passenger seatback lumbar support can be adjusted by moving the control located on the outboard side of the seat cushions. T o increase or decrease support, hold the control forward or rearward.
Seats and Restraints 2-7 Thigh Support Adjustment On vehicles with this feature, adjust the manual leg extension by reaching under it, in the pocketed area. Press the release button and pull or push to lengthen or shorten it. Release the button to lock it in place.
2-8 Seats and Restraints T o return the seatback to an upright position: 1. Lift the lever fully without applying pressure to the seatback and the seatback will return to the upright position. 2. Push and pull on the seatback to make sure it is locked.
Seats and Restraints 2-9 Do not have a seatback reclined if the vehicle is moving. Heated and V entilated Front Seats { W ARNING If you cannot feel temperature change or pain to the skin, the seat heater may cause burns even at low temperatures.
2-10 Seats and Restraints Rear Seats Notice: Folding a rear seat with the safety belts still fastened may cause damage to the seat or the safety belts. Always unbuckle the safety belts and return them to their normal stowed position before folding a rear seat.
Seats and Restraints 2-1 1 T o return a seatback to the upright position: { W ARNING If either seatback is not locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always push and pull on the seatbacks to be sure they are locked.
2-12 Seats and Restraints In most states and in all Canadian provinces, the law requires wearing safety belts. Here is why: Y ou never know if you will be in a crash. If you do have a crash, you do not know if it will be a serious one. A few crashes are mild, and some crashes can be so serious that even buckled up, a person would not survive.
Seats and Restraints 2-13 Get it up to speed. Then stop the vehicle. The rider does not stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield.
2-14 Seats and Restraints or the safety belts! With safety belts, you slow down as the vehicle does. Y ou get more time to stop. Y ou stop over more distance, and your strongest bones take the forces.
Seats and Restraints 2-15 How to Wear Safety Belts Properly This section is only for people of adult size. Be aware that there are special things to know about safety belts and children.
2-16 Seats and Restraints Q: What is wrong with this? A: The shoulder belt is too loose. It will not give as much protection this way . { W ARNING Y ou can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury .
Seats and Restraints 2-17 { W ARNING Y ou can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen. This could cause serious or even fatal injuries. The lap belt should be worn low and snug on the hips, just touching the thighs.
2-18 Seats and Restraints Q: What is wrong with this? A: The belt is over an armrest. { W ARNING Y ou can be seriously injured if your belt goes over an armrest like this.
Seats and Restraints 2-19 { W ARNING Y ou can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury . Also, the belt would apply too much force to the ribs, which are not as strong as shoulder bones.
2-20 Seats and Restraints Q: What is wrong with this? A: The belt is twisted across the body . { W ARNING Y ou can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly , or ask your dealer/retailer to fix it.
Seats and Restraints 2-21 3. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure. If the belt is not long enough, see Safety Belt Extender on page 2 ‑ 25 . Position the release button on the buckle so that the safety belt could be quickly unbuckled if necessary .
2-22 Seats and Restraints Shoulder Belt Height Adjuster The vehicle has a shoulder belt height adjuster for the driver and right front passenger seating positions. Adjust the height so that the shoulder portion of the belt is centered on the shoulder .
Seats and Restraints 2-23 Rear Safety Belt Comfort Guides This vehicle may have rear shoulder belt comfort guides. If not, they are available through your dealer/retailer . The guides may provide added safety belt comfort for older children who have outgrown booster seats and for some adults.
2-24 Seats and Restraints 3. Be sure that the belt is not twisted and it lies flat. The elastic cord must be under the belt and the guide on top. { W ARNING A safety belt that is not properly worn may not provide the protection needed in a crash. The person wearing the belt could be seriously injured.
Seats and Restraints 2-25 Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts.
2-26 Seats and Restraints Safety Belt Care Keep belts clean and dry . { W ARNING Do not bleach or dye safety belts. It may severely weaken them. In a crash, they might not be able to provide adequate protection. Clean safety belts only with mild soap and lukewarm water .
Seats and Restraints 2-27 Airbag System The vehicle has the following airbags: . A frontal airbag for the driver . . A frontal airbag for the right front passenger . . A seat-mounted side impact airbag for the driver . . A seat-mounted side impact airbag for the right front passenger .
2-28 Seats and Restraints { W ARNING Airbags inflate with great force, faster than the blink of an eye. Anyone who is up against, or very close to, any airbag when it inflates can be seriously injured or killed. Do not sit unnecessarily close to the airbag, as you would be if you were sitting on the edge of your seat or leaning forward.
Seats and Restraints 2-29 Where Are the Airbags? The driver's frontal airbag is in the middle of the steering wheel. The right front passenger frontal airbag is in the instrument panel on the passenger side.
2-30 Seats and Restraints Driver Side shown, Passenger Side similar The roof-rail airbags for the driver , right front passenger , and second row outboard passengers are in the ceiling above the side windows.
Seats and Restraints 2-31 When Should an Airbag Inflate? Frontal airbags are designed to inflate in moderate to severe frontal or near-frontal crashes to help reduce the potential for severe injuries mainly to the driver's or right front passenger's head and chest.
2-32 Seats and Restraints Seat-mounted side impact and roof-rail airbags are intended to inflate in moderate to severe side crashes. In addition, these roof-rail airbags are intended to inflate during a rollover or in a severe frontal impact.
Seats and Restraints 2-33 How Does an Airbag Restrain? In moderate to severe frontal or near frontal collisions, even belted occupants can contact the steering wheel or the instrument panel. In moderate to severe side collisions, even belted occupants can contact the inside of the vehicle.
2-34 Seats and Restraints The parts of the airbag that come into contact with you may be warm, but not too hot to touch. There may be some smoke and dust coming from the vents in the deflated airbags.
Seats and Restraints 2-35 . The vehicle has a crash sensing and diagnostic module which records information after a crash. See V ehicle Data Recording and Privacy on page 12 ‑ 15 and Event Data Recorders on page 12 ‑ 15 . . Let only qualified technicians work on the airbag systems.
2-36 Seats and Restraints The passenger sensing system works with sensors that are part of the right front passenger seat. The sensors are designed to detect the presence of a properly-seated occupant and determine if the right front passenger frontal airbag should be enabled (may inflate) or not.
Seats and Restraints 2-37 The passenger sensing system is designed to turn off the right front passenger airbag if: . The right front passenger seat is unoccupied. . The system determines an infant is present in a child restraint. . A right front passenger takes his/her weight off of the seat for a period of time.
2-38 Seats and Restraints If the On Indicator is Lit for a Child Restraint If a child restraint has been installed and the on indicator is lit: 1. T urn the vehicle off. 2. Remove the child restraint from the vehicle. 3. Remove any additional items from the seat such as blankets, cushions, seat covers, seat heaters, or seat massagers.
Seats and Restraints 2-39 If this happens, use the following steps to allow the system to detect that person and enable the right front passenger frontal airbag: 1. T urn the vehicle off. 2. Remove any additional material from the seat, such as blankets, cushions, seat covers, seat heaters, or seat massagers.
2-40 Seats and Restraints The on indicator may be lit if an object, such as a briefcase, handbag, grocery bag, laptop or other electronic device, is put on an unoccupied seat.
Seats and Restraints 2-41 In addition, the vehicle has a passenger sensing system for the right front passenger position, which includes sensors that are part of the passenger seat.
2-42 Seats and Restraints Airbag System Check The airbag system does not need regularly scheduled maintenance or replacement. Make sure the airbag readiness light is working. See Airbag Readiness Light on page 4 ‑ 21 for more information. Notice: If an airbag covering is damaged, opened, or broken, the airbag may not work properly .
Seats and Restraints 2-43 Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle's safety belts. The manufacturer's instructions that come with the booster seat, state the weight and height limitations for that booster .
2-44 Seats and Restraints According to accident statistics, children and infants are safer when properly restrained in a child restraint system or infant restraint system secured in a rear seating position. In a crash, children who are not buckled up can strike other people who are buckled up, or can be thrown out of the vehicle.
Seats and Restraints 2-45 Infants and Y oung Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints.
2-46 Seats and Restraints { W ARNING Never do this. Children who are up against, or very close to, any airbag when it inflates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat.
Seats and Restraints 2-47 { W ARNING T o reduce the risk of neck and head injury during a crash, infants need complete support. This is because an infant's neck is not fully developed and its head weighs so much compared with the rest of its body .
2-48 Seats and Restraints (B) Forward-Facing Child Seat A forward-facing child seat (B) provides restraint for the child's body with the harness. (C) Booster Seats A booster seat (C) is a child restraint designed to improve the fit of the vehicle's safety belt system.
Seats and Restraints 2-49 the LA TCH system. See Lower Anchors and T ethers for Children (LA TCH System) on page 2 ‑ 51 for more information. Children can be endangered in a crash if the child restraint is not properly secured in the vehicle.
2-50 Seats and Restraints A label on the sun visor says, “ Never put a rear-facing child restraint in the front. ” This is because the risk to the rear-facing child is so great, if the airbag deploys. { W ARNING A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inflates.
Seats and Restraints 2-51 Lower Anchors and T ethers for Children (LA TCH System) The LA TCH system holds a child restraint during driving or in a crash.
2-52 Seats and Restraints T op T ether Anchor A top tether (A, C) anchors the top of the child restraint to the vehicle. A top tether anchor is built into the vehicle.
Seats and Restraints 2-53 T o assist you in locating the lower anchors, each seating position with lower anchors has two labels, near the crease between the seatback and the seat cushion. For a wagon the lower anchors are beneath zippers, located near the labels.
2-54 Seats and Restraints Securing a Child Restraint Designed for the LA TCH System { W ARNING If a LA TCH-type child restraint is not attached to anchors, the child restraint will not be able to protect the child correctly . In a crash, the child could be seriously injured or killed.
Seats and Restraints 2-55 1. Attach and tighten the lower attachments to the lower anchors. If the child restraint does not have lower attachments or the desired seating position does not have lower anchors, secure the child restraint with the top tether and the safety belts.
2-56 Seats and Restraints If the position you are using does not have a headrest or head restraint and you are using a dual tether , route the tether over the seatback. If the position you are using has a fixed headrest or head restraint and you are using a dual tether , route the tether around the headrest or head restraint.
Seats and Restraints 2-57 Replacing LA TCH System Parts After a Crash { W ARNING A crash can damage the LA TCH system in the vehicle. A damaged LA TCH system may not properly secure the child restraint, resulting in serious injury or even death in a crash.
2-58 Seats and Restraints If the child restraint does not have the LA TCH system, you will be using the safety belt to secure the child restraint in this position. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say .
Seats and Restraints 2-59 5. T o tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt, and feed the shoulder belt back into the retractor .
2-60 Seats and Restraints A label on the sun visor says, “ Never put a rear-facing child seat in the front. ” This is because the risk to the rear-facing child is so great, if the airbag deploys. { W ARNING A child in a rear-facing child restraint can be seriously injured or killed if the front passenger airbag inflates.
Seats and Restraints 2-61 Y ou will be using the lap-shoulder belt to secure the child restraint in this position. Follow the instructions that came with the child restraint. 1. Move the seat as far back as it will go before securing the forward-facing child restraint.
2-62 Seats and Restraints 6. T o tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor .
Storage 3-1 Storage Storage Compartments Instrument Panel Storage . . . . 3-1 Glove Box . . . . . . . . . . . . . . . . . . . . 3-1 Cupholders . . . . . . . . . . . . . . . . . . . 3-1 Center Console Storage . . . . . . 3-1 Additional Storage Features Cargo Cover .
3-2 Storage Additional Storage Features Cargo Cover The cargo cover can be used to cover items in the cargo area of the vehicle. T o install the cargo cover: 1. Hold the cartridge so that the pull out shade faces backwards. 2. Align the cartridge over the pin (B) on both sides.
Storage 3-3 { W ARNING An improperly stored cargo cover could be thrown about the vehicle during a collision or sudden maneuver . Someone could be injured. If the cover is removed, always store it in the proper storage location. When it is replaced, always be sure that it is securely reattached.
3-4 Storage D-Ring Sliders There are four D-Ring sliders that move along rails on both sides of the cargo management area. These can be used as tie-downs when storing cargo. Installing D-Ring Sliders T o install the D-Ring slider (A), insert it into the channel (B) located in the middle of each rail.
Storage 3-5 1. There are four installation openings in the roof, two located in front of and two behind the rear seats. Insert the top corners of the cargo net into the large opening in the roof and secure by sliding them into the small opening. 2. There are four tether positions for the lower hook straps.
3-6 Storage 5. Pull on the straps to tighten the net. Put light loads behind the net to keep them from falling over or being thrown into the cabin during heavy braking. The net should not be overloaded or used to store heavy loads. Convenience Net (Sedan) Y our vehicle may have a convenience net in the rear of the vehicle.
Storage 3-7 For vehicles with a roof rack, the rack can be used to load items. For roof racks that do not have crossrails included, GM Certified crossrails can be purchased as an accessory .
3-8 Storage 3. Store the siderail covers in a place where it can be laid flat. Do not stack any items on top of the cover . 4. Identify front and rear crossrail by the size of the crossrail support. 5. The front crossrail support (A) is smaller than the rear crossrail support (B).
Storage 3-9 9. Levers must still be in the forward up position. For front crossbar , slide the crossrail assembly (A) forward until the crossrail end is past the channel cut-out area (B). For rear crossbar , slide the crossrail assembly (A) rearward until the entire crossrail support is in first position to the rear of the channel cut-out area (B).
3-10 Storage 2 NOTES.
Instruments and Controls 4-1 Instruments and Controls Instrument Panel Overview Instrument Panel Overview . . . . 4-4 Controls Steering Wheel Adjustment . . . 4-6 Steering Wheel Controls . . . . . . 4-7 Horn . . . . . . . . . . . . . . . . . . . . . .
4-2 Instruments and Controls V ehicle Messages V ehicle Messages . . . . . . . . . . . 4-36 Battery V oltage and Charging Messages . . . . . . . . . . . . . . . . . . 4-37 Brake System Messages . . . . 4-38 Compass Messages . . . . . . . . . 4-39 Cruise Control Messages .
Instruments and Controls 4-3 2 NOTES.
4-4 Instruments and Controls Instrument Panel Overview CTS Shown, CTS-V Similar.
Instruments and Controls 4-5 A. Air V ents on page 7 ‑ 6 . B. Driver Information Center (DIC) on page 4 ‑ 31 . C. Instrument Panel Illumination Control on page 5 ‑ 5 . D. T urn and Lane-Change Signals on page 5 ‑ 4 . E. Instrument Cluster on page 4 ‑ 15 .
4-6 Instruments and Controls Controls Steering Wheel Adjustment A tilt and telescope wheel lets the steering wheel be adjusted. Do not adjust the steering wheel while driving. The tilt and telescope lever is on the left side of the steering column. T o tilt and telescope the steering wheel, pull the lever down.
Instruments and Controls 4-7 Steering Wheel Controls Some audio steering wheel controls could differ depending on the vehicle's options. Controls that can be adjusted at the steering wheel may in.
4-8 Instruments and Controls Windshield Wiper/W asher Sedan Model shown Wagon Model shown The windshield wiper lever is on the right side of the steering column. Move the windshield wiper lever to select the wiper speed. 7 (Mist): Single wipe, briefly move the lever down and release.
Instruments and Controls 4-9 Windshield W asher { W ARNING In freezing weather , do not use your washer until the windshield is warmed. Otherwise the washer fluid can form ice on the windshield, blocking your vision. Sedan Model K (W asher Fluid): Press the button with this symbol, on the end of the windshield washer lever , to wash the windshield.
4-10 Instruments and Controls Z (Rear Wiper Delay Short): Sets a five second delay between wipes. 5 (Rear Wiper Delay Long): Sets a ten second delay between wipes. = (Rear W asher): Push the windshield wiper lever forward to spray washer fluid on the rear window .
Instruments and Controls 4-1 1 Compass The vehicle may have a compass in the Driver Information Center (DIC). Compass Zone The zone is set to zone eight. If you do not live in zone eight or drive out of the area, the variance needs to be changed to the appropriate zone.
4-12 Instruments and Controls T o calibrate the compass, use the following procedure: Compass Calibration Procedure 1. Before calibrating the compass, check that the compass is set to the correct variance zone. See “ Compass V ariance (Zone) Procedure ” earlier in this section.
Instruments and Controls 4-13 T o use an outlet, remove the protective cap. When not in use, always cover the outlet with the protective cap. The accessory power outlet is operational at all times. Notice: If electrical devices are left plugged into a power outlet, the battery may drain causing the vehicle not to start or damage to the battery .
4-14 Instruments and Controls Ashtrays The vehicle may have two removable ashtrays. One ashtray can be placed into the instrument panel storage compartment and the other into the center console rear compartment. T o empty the ashtrays, hold on to the edges of the bin and pull straight out.
Instruments and Controls 4-15 Instrument Cluster United States Automatic T ransmission Cluster Shown, Canada and Manual Similar.
4-16 Instruments and Controls United States V -Series Automatic T ransmission Cluster Shown, Canada and Manual Similar.
Instruments and Controls 4-17 Speedometer The speedometer shows the vehicle's speed in both kilometers per hour (km/h) and miles per hour (mph). Odometer The odometer shows how far the vehicle has been driven, in either kilometers or miles. If this vehicle has to have a new odometer installed, the new one may read the correct mileage.
4-18 Instruments and Controls The Fuel Level Low message appears in the Driver Information Center (DIC) and a single chime sounds. See Fuel System Messages on page 4 ‑ 42 for more information. Here are four things that some owners ask about. None of these show a problem with your fuel gage: .
Instruments and Controls 4-19 Engine Speed Limiter This feature prevents the engine speed from reaching an unsafe level. If the level is too high, the throttle closes or limits the fuel supply until the engine speed returns to a safe level. Throttle operation and fuel supply returns to normal when engine speed is lowered.
4-20 Instruments and Controls A reading outside the normal operating range may be caused by a dangerously low oil level or some other problem causing low oil pressure. Oil should be checked as soon as possible. See Oil Pressure Low Stop Engine under Driver Information Center (DIC) on page 4 ‑ 31 and Engine Oil on page 9 ‑ 10 .
Instruments and Controls 4-21 Safety Belt Reminders Driver Safety Belt Reminder Light There is a driver safety belt reminder light on the instrument panel cluster . When the engine is started this light and a chime come on and stay on for several seconds to remind drivers to fasten their safety belts.
4-22 Instruments and Controls The airbag readiness light comes on and stays on for several seconds when the vehicle is started. Then the light goes out. { W ARNING If the airbag readiness light stays on after the vehicle is started or comes on while driving, it means the airbag system might not be working properly .
Instruments and Controls 4-23 If, after several seconds, both status indicator lights remain on, or if there are no lights at all, there may be a problem with the lights or the passenger sensing system.
4-24 Instruments and Controls If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent.
Instruments and Controls 4-25 An emission system malfunction might be corrected. . Make sure the fuel cap is fully installed. See Filling the T ank on page 8 ‑ 52 . The diagnostic system can determine if the fuel cap has been left off or improperly installed.
4-26 Instruments and Controls . The vehicle will not pass this inspection if the OBD II (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection.
Instruments and Controls 4-27 For vehicles with the Electric Park Brake (EPB), this red brake warning light comes on when the park brake is applied. If the light continues flashing after the park brake is released, or while driving, there is a problem with the Electric Parking Brake system.
4-28 Instruments and Controls Then start the engine again to reset the system. If the ABS light stays on, or comes on again while driving, the vehicle needs service. If the regular brake system warning light is not on, the vehicle still has brakes, but not antilock brakes.
Instruments and Controls 4-29 See T raction Control System (TCS) on page 8 ‑ 37 and StabiliT rak System on page 8 ‑ 38 for more information. Engine Coolant T emperature W arning Light The engine coolant temperature warning light comes on briefly when the engine is started.
4-30 Instruments and Controls Engine Oil Pressure Light { W ARNING Do not keep driving if the oil pressure is low . The engine can become so hot that it catches fire. Someone could be burned. Check the oil as soon as possible and have the vehicle serviced.
Instruments and Controls 4-31 Fog Lamp Light The fog lamp light comes on when the fog lamps are in use. The light goes out when the fog lamps are turned off. See Fog Lamps on page 5 ‑ 5 for more information. Lamps on Reminder This light comes on when the taillamps are on.
4-32 Instruments and Controls If a problem is detected, a warning message appears on the display . T ake any message that appears on the display seriously and remember that clearing the message only makes the message disappear , and does not correct the problem.
Instruments and Controls 4-33 Fuel Range This display shows the approximate number of remaining miles (mi) or kilometers (km) you can drive without refilling the fuel tank. This estimate is based on the current driving conditions and changes if the driving conditions change.
4-34 Instruments and Controls Speedometer This display shows a digital speedometer in the DIC. The speed displays in either miles per hour (mph) or kilometers per hour (km/h). T o change the units from English to metric, see “ Units ” later in this section.
Instruments and Controls 4-35 information button again until the DIC displays Rear Tire PSI (kPa) Left ## Right ##. If a low tire pressure condition is detected by the system while driving, a message advising you to add air to a specific tire appears in the display .
4-36 Instruments and Controls 4. T o learn additional transmitters at this time, repeat Step 3. Each vehicle can have a maximum of eight learned transmitters.
Instruments and Controls 4-37 The following are the possible messages that can be displayed and some information about them. Battery V oltage and Charging Messages Battery Saver Active This message displays when the system detects that the battery voltage is dropping below expected levels.
4-38 Instruments and Controls Brake System Messages Park Brake Released For vehicles with the Electric Parking Brake, this message displays when the parking brake has been released from the set position.
Instruments and Controls 4-39 Brake System Warning Light on page 4 ‑ 26 for more information. This message may also be displayed for other brake system problems.
4-40 Instruments and Controls Rear Access Open (Wagon) This message displays when the liftgate is not closed completely . Make sure that the liftgate is closed completely . Right Rear Door Open This message displays when the passenger side rear door is not closed completely .
Instruments and Controls 4-41 When you reset the Change Engine Oil Soon message by clearing it from the display , you still must reset the engine oil life system separately . For more information on resetting the engine oil life system, see Engine Oil Life System on page 9 ‑ 12 .
4-42 Instruments and Controls Fuel System Messages Fuel Level Low This message displays when the vehicle is low on fuel. Refill the fuel tank as soon as possible. A chime may sound when this message displays. See Filling the T ank on page 8 ‑ 52 . Tighten Gas Cap This message displays when the fuel cap has not been fully tightened.
Instruments and Controls 4-43 If moving the transmitter to different locations within the vehicle does not help, place the transmitter in the center console transmitter pocket with the buttons facing the front of the vehicle and then start the vehicle.
4-44 Instruments and Controls Press Start Control T o Learn Keys If the vehicle has the keyless access system, this message displays when matching new transmitters to the vehicle.
Instruments and Controls 4-45 See Adaptive Forward Lighting (AFL) on page 5 ‑ 4 for more information. Automatic Light Control Off This message displays when the automatic headlamps are turned off. Automatic Light Control On This message displays when the automatic headlamps are turned on.
4-46 Instruments and Controls Service All Wheel Drive This message displays if a problem occurs with the All-Wheel Drive (A WD) system. The vehicle will run in 2WD. This could be caused by: . An electronics problem . An A WD system oil overheat . Worn out or overheated clutch plates .
Instruments and Controls 4-47 Adjust your driving accordingly . See “ Competitive Driving Mode ” under T raction Control System (TCS) on page 8 ‑ 37 for more information. Stabilitrak Not Ready This message may display after first driving the vehicle and exceeding 30 km/h (19 mph) for 30 seconds.
4-48 Instruments and Controls Airbag System Messages Service Air Bag This message displays when there is a problem with the airbag system. Have the vehicle serviced by your dealer/retailer immediately . See Airbag Readiness Light on page 4 ‑ 21 for more information.
Instruments and Controls 4-49 comes on and stays on, there may be a problem with the TPMS. See your dealer/retailer . Tire Learning Active This message displays when the T ire Pressure Monitor System (TPMS) is re-learning the tire positions on the vehicle.
4-50 Instruments and Controls Service T ransmission This message displays when there is a problem with the vehicle's transmission. Have the vehicle serviced by your dealer/retailer .
Instruments and Controls 4-51 V ehicle Personalization V ehicle customization allows certain features to be programmed for one preferred setting. Only the customization options available will be displayed on the DIC. The default settings were preset when the vehicle left the factory , but may have been changed.
4-52 Instruments and Controls No Change: No change will be made to this feature. The current setting will remain. T o select a setting, press the set/reset button while the desired setting is displayed on the DIC. Auto Door Lock This feature allows you to select when the vehicle's doors will automatically lock.
Instruments and Controls 4-53 T o select a setting, press the set/reset button while the desired setting is displayed on the DIC. Remote Door Lock Feedback This feature allows you to select the type o.
4-54 Instruments and Controls Press the customization button until Remote Door Unlock appears on the DIC display . Press the set/reset button once to access the settings for this feature.
Instruments and Controls 4-55 No Change: No change will be made to this feature. The current setting will remain. T o select a setting, press the set/reset button while the desired setting is displayed on the DIC. Factory Settings This feature allows you to set all of the customization features back to their factory default settings.
4-56 Instruments and Controls Press the customization button until Keyless Locking appears on the DIC display . Press the set/reset button once to access the settings for this feature. Then press the menu up/down button to scroll through the following settings: Off (default): The keyless locking feature will be disabled.
Instruments and Controls 4-57 Press the customization button until Chime V olume appears on the DIC display . Press the set/reset button once to access the settings for this feature. Then press the menu up/ down button to scroll through the following settings: Normal: The chime volume will be set to a normal level.
4-58 Instruments and Controls The automatic easy exit seat movement will only occur one time after the key is removed from the ignition. If the automatic movement has already occurred, and you put the.
Instruments and Controls 4-59 OnStar ® System OnStar ® uses several innovative technologies and live advisors to provide a wide range of safety , security , navigation, diagnostics, and calling services.
4-60 Instruments and Controls The OnStar system can record and transmit vehicle information. This information is automatically sent to an OnStar call center when Q is pressed, ] is pressed, or if the airbags or ACR system deploy .
Instruments and Controls 4-61 Universal Remote System See Radio Frequency Statement on page 12 ‑ 16 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and RSS-210/21 1 of Industry and Science Canada.
4-62 Instruments and Controls Programming the Universal Home Remote System For questions or help programming the Universal Home Remote System, call 1 ‐ 800 ‐ 355 ‐ 3515 or go to www .homelink.com. Programming a garage door opener involves time-sensitive actions, so read the entire procedure before starting.
Instruments and Controls 4-63 3. At the same time, press and hold both the Universal Home Remote button to be used to control the garage door and the hand-held transmitter button. Do not release the Universal Home Remote button or the hand-held transmitter button until Step 4 has been completed.
4-64 Instruments and Controls 6. After Steps 1 through 5 have been completed, locate inside the garage the garage door opener receiver (motor-head unit). Locate the “ Learn ” or “ Smart ” button. The name and color of the button may vary by manufacturer .
Instruments and Controls 4-65 Gate Operator and Canadian Programming If you have questions or need help programming the Universal Home Remote System, call 1-800-355-3515 or go to www .homelink.com. Canadian radio-frequency laws require transmitter signals to time out or quit after several seconds of transmission.
4-66 Instruments and Controls Erasing Universal Remote Buttons All programmed buttons should be erased when the vehicle is sold or the lease ends. T o erase all programmed buttons on the Universal Remote device: 1. Press and hold down the two outside buttons until the indicator light begins to flash, after 20 seconds.
Lighting 5-1 Lighting Exterior Lighting Exterior Lamp Controls . . . . . . . . 5-1 Exterior Lamps Off Reminder . . . . . . . . . . . . . . . . . . . . 5-2 Headlamp High/Low-Beam Changer . . . . . . . . . . . . . . . . . . . . . 5-2 Flash-to-Pass . . .
5-2 Lighting ; (Parking Lamps): T urns on the parking lamps together with the following: . Sidemarker Lamps . T aillamps . License Plate Lamps . Instrument Panel Lights 5 (Headlamps): T urns on the headlamps, together with the previously listed lamps and lights.
Lighting 5-3 Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day . Fully functional daytime running lamps are required on all vehicles first sold in Canada.
5-4 Lighting Adaptive Forward Lighting (AFL) The Adaptive Forward Lighting System (AFL) pivots the headlamps horizontally to provide greater road illumination while turning. T o enable AFL, set the exterior lamp switch on the multifunction lever to the AUTO position.
Lighting 5-5 Fog Lamps Use the fog lamps for better vision in foggy or misty conditions. The fog lamp control is located on the turn signal/multifunction lever . # (Fog Lamps): T urn the fog lamp band on the lever up to # and release it, to turn the fog lamps on or off.
5-6 Lighting Lighting Features Entry Lighting The entry lighting system turns on the reading and dome lamps and the backlighting to the exterior lamp control, when a door is opened or if the transmitter unlock button is pressed. If activated by the transmitter , the lighting stays on for about 25 seconds.
Lighting 5-7 This is because the generator (alternator) may not be spinning fast enough at idle to produce all the power that is needed for very high electrical loads.
5-8 Lighting 2 NOTES.
Infotainment System 6-1 Infotainment System Introduction Introduction . . . . . . . . . . . . . . . . . . . 6-1 Theft-Deterrent Feature . . . . . . . 6-2 Operation . . . . . . . . . . . . . . . . . . . . . 6-2 Radio AM-FM Radio . . . . . . . . . . . .
6-2 Infotainment System Navigation/Radio System For vehicles with a navigation radio system, see the separate Navigation System manual. Theft-Deterrent Feature THEFTLOCK ® is designed to discourage theft of the vehicle's radio by learning a portion of the V ehicle Identification Number (VIN).
Infotainment System 6-3 Partial View of Radio with DVD Audio, Hard Drive Device (HDD), and USB The vehicle may have one of these radios as its audio system. If the vehicle does not have one of these radio systems, it may have a navigation radio system.
6-4 Infotainment System 4. T o decrease the highlighted setting, do one of the following: . T urn the TUNE/TONE knob counterclockwise. . Press the s REV button. . Press the © SEEK button. T o quickly adjust bass, midrange, or treble to the middle position, press the softkey under the BASS, MID, or TREB tab for more than two seconds.
Infotainment System 6-5 The DSP settings available are: . Normal : Select for normal mode, this provides the best sound quality for all seating positions. . Driver : Select to adjust the audio for the driver to receive the best possible sound quality .
6-6 Infotainment System Speed Compensated V olume (SCV) A Radio with SCV automatically adjusts the sound to compensate for road and wind noise as the vehicle speeds up or slows down, so that the volume is consistent while driving. T o activate SCV: 1.
Infotainment System 6-7 Dolby and the double-D symbol are trademarks of Dolby Laboratories. Manufactured under license from Dolby Laboratories. Gracenote ® Database Gracenote Music Recognition Service, Music recognition technology , and related data are provided by Gracenote ® .
6-8 Infotainment System Y ou agree that your non-exclusive license to use the Gracenote Data, the Gracenote Software, and Gracenote Servers will terminate if you violate these restrictions. If your license terminates, you agree to cease any and all use of the Gracenote Data, the Gracenote Software, and Gracenote Servers.
Infotainment System 6-9 Radio AM-FM Radio Control Buttons The buttons used to control the radio are: FM/AM: Press to choose between FM and AM. m : Press to choose the XM ™ band (if equipped). TUNE: T urn to search for stations. MENU/SELECT : Turn clockwise or counterclockwise to scroll through the station list.
6-10 Infotainment System Storing a Radio Station as a Favorite Drivers are encouraged to set up their radio station favorites while the vehicle is stopped. Tune to favorite stations using the presets, favorites button, and steering wheel controls, if the vehicle has this feature.
Infotainment System 6-1 1 T o resume playback from the current pause point, press r / j again. The radio will no longer be playing “ live ” radio. Instead, time shifted content is being played from the buffer .
6-12 Infotainment System Control Buttons The buttons used to control the radio are: m : Press to choose the XM ™ band (if equipped). TUNE: T urn to search for stations. MENU/SELECT : Turn clockwise or counterclockwise to scroll through the category list.
Infotainment System 6-13 m : Press to switch to XM mode. T urn the TUNE/TONE knob to select from a list of available XM stations. T urn the TUNE/TONE knob until the desired station is highlighted. Press the TUNE/TONE knob to select the highlighted station.
6-14 Infotainment System XM Messages XL (Explicit Language Channels): These channels, or any others, can be blocked at a customer's request, by calling 1-800-852-XMXM (9696). XM Updating: The encryption code in the receiver is being updated, and no action is required.
Infotainment System 6-15 XM Not A vailable: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer/ retailer .
6-16 Infotainment System Audio Players CD Player The Infotainment system's CD player can play audio CDs and MP3 CDs. CDs that are 8 cm (3 in.) in diameter will not work in the CD player .
Infotainment System 6-17 FWD (Fast Forward): Press and hold to advance playback quickly within a track. ^ (Load) : Press to load CDs into the Six-Disc CD player . Z (Eject): Press to eject the disc. For the Six-Disc CD player , press and hold for two seconds to eject all discs.
6-18 Infotainment System The CD begins playback of the first track on the selected disc. As each new track starts to play the track number displays in the left and center of the screen. Playing a CD Selecting a CD T rack T racks can be selected using the seek buttons, TUNE/TONE knob, or the MENU/SELECT knob.
Infotainment System 6-19 . The road is very rough. When the road becomes smoother , the disc should play . . The disc is dirty , scratched, wet, or upside down. . The air is very humid. If so, wait about an hour and try again. . There could have been a problem while burning the disc.
6-20 Infotainment System The use of disc lens cleaners for discs is not advised, due to the risk of contaminating the lens of the disc optics with lubricants internal to the CD/DVD player mechanism.
Infotainment System 6-21 Press the ¨ SEEK button to go to the next track. If © SEEK or ¨ SEEK is held, or pressed multiple times, the player continues moving backward or forward through the tracks on the CD. T o use the TUNE/TONE knob: T urn the TUNE/TONE knob to highlight the desired track then press the TUNE/TONE knob to select the track.
6-22 Infotainment System T o use the MENU/SELECT knob: Press the softkey under the Menu tab to display a list of all Groups. T o change Groups, turn the MENU/ SELECT knob to highlight the desired Group. Press the MENU/ SELECT knob to select it. Playback begins from track 1 of the highlighted Group.
Infotainment System 6-23 Check the DSP settings to determine if a 5.1 surround sound Audio Stream is playing. See Operation on page 6 ‑ 2 for more information. Press the DSP tab to see if the 5.1 + Normal or 5.1 + Rear settings are available for selection.
6-24 Infotainment System Creating an MP3/WMA Disc When creating a MP3/WMA disc: . Make sure the MP3/WMA files are recorded on a CD-R or CD-RW disc. . Do not mix standard audio and MP3/WMA files on one disc. . Make sure the CD does not have more than a maximum of 50 folders and playlists, and 255 files to read and play .
Infotainment System 6-25 Empty Directory or Folder If a root directory or a folder exists somewhere in the file structure that contains only folders/subfolders and no compressed files directly beneath them, the player advances to the next folder in the file structure that contains compressed audio files.
6-26 Infotainment System Playlists can be selected using the previous and next folder buttons. T racks can be changed by pressing the seek buttons or turning the tune knob. Songs are played sequentially; press the s REV or FWD to reverse or advance through the playing song.
Infotainment System 6-27 Searching for MP3 T racks T racks can be searched for by using the menu system. T o use the menu system: 1. Press the MENU/SELECT knob to display the MP3 Menu. 2. T urn the MENU/SELECT knob to highlight an option from the MP3 Menu.
6-28 Infotainment System Copy Protected CD(s) Make sure the disc is not copy-protected. The radio does not copy a copy-protected CD to the HDD. Deleting a Recorded Song or Category DEL (Delete): Press the DEL button to delete the track that is currently playing or select a track from one of the song lists.
Infotainment System 6-29 Songs recorded with “ NO INFO ” to the HDD will be hard to sort, identify , and select. T o make HDD navigation easier , CDs with “ NO INFO ” can first be converted to MP3 format with T ag information on a home computer and then recorded to the HDD from an MP3 disc or USB device.
6-30 Infotainment System USB Host Support The USB connector uses the USB standards, 1.1 and 2.0. USB Supported Devices . USB Flash Drives . Portable USB Hard Drives Playing From the Hard Drive Device HDD (Hard Drive Device): Press the HDD button to start playing tracks from the HDD.
Infotainment System 6-31 HDD Menu 1. Press the MENU/SELECT knob to display the HDD Menu. 2. T urn the MENU/SELECT knob to highlight an option from the HDD Menu. The available options are: . Shuffle Songs . Playlist . Artists . Albums . Song T itles . Genres .
6-32 Infotainment System HDD Categories The HDD category mode can be used to select a song by a particular artist, album, or genre for playback. As an example, the HDD Menu displays a layout such as: .
Infotainment System 6-33 Saving HDD Favorites Press the F A V button to change between favorite modes during HDD playback. The following favorite modes are supported: . Playlists . Artists . Albums . Genres Favorites can be saved by pressing and holding the softkey under the favorites selection.
6-34 Infotainment System Press r / j (play/pause) T o pause the radio. The radio display will show the Time Shift buffer status bar . The status bar shows the amount of content that is stored in the buffer and the current pause point. T o resume playback from the current pause point, press r / j again.
Infotainment System 6-35 Auxiliary Devices The 3.5mm (1/8 in.) input jack and the USB port (if equipped), located in the center console bin, allows portable devices to connect to the vehicle. This is not an audio output; do not plug headphones into the auxiliary input jack.
6-36 Infotainment System Connecting an iPod T o connect the iPod, connect one end of the special iPod connection cable to the iPod ’ s dock connector . Connect the other end to both the USB port and the auxiliary input jack located in the center console.
Infotainment System 6-37 Phone Bluetooth V ehicles with a Bluetooth system can use a Bluetooth capable cell phone with a Hands Free Profile to make and receive phone calls. The system can be used while the ignition is in ON/RUN or ACC/ ACCESSORY position.
6-38 Infotainment System Pairing Information: . Up to five cell phones can be paired to the in-vehicle Bluetooth system. . The pairing process is disabled when the vehicle is moving. . The in-vehicle Bluetooth system automatically links with the first available paired cell phone in the order the phone was paired.
Infotainment System 6-39 Listing All Paired and Connected Phones 1. Press and hold b g for two seconds: . For vehicles without a navigation system, the system responds with “ Ready ” followed by a tone. . For vehicles with a navigation system, the system responds with a tone.
6-40 Infotainment System 3. Say “ Change phone ” . The system responds with “ Please wait while I search for other phones ” . . If another phone is found, the response will be “ <Phone name> is now connected ” . . If another phone is not found, the original phone remains connected.
Infotainment System 6-41 5. Say a name tag for the phone number . The name tag is recorded and the system responds with “ About to store <name tag>. Does that sound OK? ” . . If the name tag does not sound correct, say “ No ” and repeat Step 5.
6-42 Infotainment System Using the Directory Command The directory command lists all of the name tags stored by the system. T o use the directory command: 1. Press and hold b g for two seconds: . For vehicles without a navigation system, the system responds with “ Ready ” followed by a tone.
Infotainment System 6-43 Using the Delete All Name T ags Command The delete all name tags command deletes all stored phone book name tags and route name tags for OnStar (if present). T o use the delete all name tags command: 1. Press and hold b g for two seconds: .
6-44 Infotainment System 3. Say the entire number without pausing. . If the system recognizes the number , it responds with “ OK, Dialing ” and dials the number . . If the system does not recognize the number , it confirms the numbers followed by a tone.
Infotainment System 6-45 3. Say the name tag of the person to call. . If the system clearly recognizes the name tag it responds with “ OK, calling, <name tag> ” and dials the number . . If the system is unsure it recognizes the right name tag, it confirms the name tag followed by a tone.
6-46 Infotainment System Three-W ay Calling Three-W ay Calling must be supported on the Bluetooth phone and enabled by the wireless service carrier to work. 1. While on a call press b g . The system responds with “ Ready ” followed by a tone. 2. Say “ Three-way call ” .
Infotainment System 6-47 T o T ransfer Audio to the In-V ehicle Bluetooth System The cellular phone must be paired and connected with the Bluetooth system before a call can be transferred. The connection process can take up to two minutes after the ignition is turned to the ON/RUN or ACC/ACCESSORY position.
6-48 Infotainment System 3. Say the number to send. . If the system clearly recognizes the number it responds with “ OK, Sending Number ” and the dial tones are sent and the call continues. . If the system is not sure it recognized the number properly , it responds “ Dial Number , Please say yes or no? ” followed by a tone.
Climate Controls 7-1 Climate Controls Climate Control Systems Dual Automatic Climate Control System . . . . . . . . . . . . . . . . . . . . . . 7-1 Air V ents Air Vents . . . . . . . . . . . . . . . . . . . . . . 7-6 Maintenance Passenger Compartment Air F i l t e r .
7-2 Climate Controls Automatic Operation AUTO (Automatic): The system automatically controls fan speed, air delivery , and air conditioning in order to heat or cool the vehicle to the desired temperature. When the indicator light is on, the system is in full automatic operation.
Climate Controls 7-3 If the airflow seems low when the fan speed is at the highest setting, the passenger compartment air filter might need to be replaced. For more information, see Passenger Compartment Air Filter on page 7 ‑ 6 and Scheduled Maintenance on page 10 ‑ 3 .
7-4 Climate Controls Recirculation is not available in the defrost mode and automatically turns off 10 minutes after defog is selected. This helps to limit window fogging in the vehicle. Using recirculation for long periods of time could cause the air inside the vehicle to become too dry or stuffy .
Climate Controls 7-5 Sensors The solar sensor located on the instrument panel, near the windshield, monitors the solar heat. The interior temperature sensor located on the instrument panel to the right of the steering wheel, measures the temperature of the air inside the vehicle.
7-6 Climate Controls Under certain conditions, the air quality sensor will not activate recirculation, such as during cold weather or with odors, like skunk. T o limit odors manually , press M until the condition has passed. The air quality sensor system does not protect against carbon monoxide (CO), which you cannot see or smell.
Climate Controls 7-7 The passenger compartment air filter is located under the hood below the windshield wiper arm and the screen on the passenger side of the vehicle. See Engine Compartment Overview on page 9 ‑ 6 for more information on location. T o replace the passenger compartment air filter: 1.
7-8 Climate Controls 2 NOTES.
Driving and Operating 8-1 Driving and Operating Driving Information Driving for Better Fuel Economy . . . . . . . . . . . . . . . . . . . . 8-2 Defensive Driving . . . . . . . . . . . . . 8-3 Drunk Driving . . . . . . . . . . . . . . . . . 8-3 Control of a V ehicle .
8-2 Driving and Operating Fuel Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 8-49 Recommended Fuel . . . . . . . . . 8-49 Gasoline Specifications . . . . . . 8-50 California Fuel Requirements . . . . . . . . . . . . . . 8-50 Fuels in Foreign Countries .
Driving and Operating 8-3 Defensive Driving Defensive driving means “ always expect the unexpected. ” The first step in driving defensively is to wear your safety belt, see Safety Belts on page 2 ‑ 1 1 . { W ARNING Assume that other road users (pedestrians, bicyclists, and other drivers) are going to be careless and make mistakes.
8-4 Driving and Operating spinal cord, or heart. This means that when anyone who has been drinking — driver or passenger — is in a crash, that person's chance of being killed or permanently disabled is higher than if the person had not been drinking.
Driving and Operating 8-5 If the engine ever stops while the vehicle is being driven, brake normally but do not pump the brakes. If the brakes are pumped, the pedal could get harder to push down. If the engine stops, there will still be some power brake assist but it will be used when the brake is applied.
8-6 Driving and Operating Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and find a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Driving and Operating 8-7 tire contacts the pavement edge. Then turn the steering wheel to go straight down the roadway . Loss of Control Let us review what driving experts say about what happens when.
8-8 Driving and Operating Competitive Driving Competitive driving may affect the vehicle warranty . See the warranty book before using the vehicle for competitive driving. Notice: If you use your vehicle for competitive driving, the engine may use more oil than it would with normal use.
Driving and Operating 8-9 Hydroplaning Hydroplaning is dangerous. Water can build up under your vehicle's tires so they actually ride on the water . This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road.
8-10 Driving and Operating { W ARNING Coasting downhill in N (Neutral) or with the ignition off is dangerous. The brakes will have to do all the work of slowing down and they could get so hot that they would not work well. Y ou would then have poor braking or even none going down a hill.
Driving and Operating 8-1 1 Blizzard Conditions Being stuck in snow can be a serious situation. Stay with the vehicle unless there is help nearby . If possible, use the Roadside Service on page 12 ‑ 6 . T o get help and keep everyone in the vehicle safe: .
8-12 Driving and Operating Repeat this until help arrives but only when you feel really uncomfortable from the cold. Moving about to keep warm also helps. If it takes some time for help to arrive, now and then when you run the engine, push the accelerator pedal slightly so the engine runs faster than the idle speed.
Driving and Operating 8-13 T wo labels on the vehicle show how much weight it may properly carry , the T ire and Loading Information label and the Certification label. { W ARNING Do not load the vehicle any heavier than the Gross V ehicle Weight Rating (GVWR), or either the maximum front or rear Gross Axle Weight Rating (GAWR).
8-14 Driving and Operating Steps for Determining Correct Load Limit 1. Locate the statement “ The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs ” on your vehicle's placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.
Driving and Operating 8-15 Example 2 A. V ehicle Capacity Weight for Example 2 = 453 kg (1,000 lbs). B. Subtract Occupant Weight @ 68 kg (150 lbs) × 5 = 340 kg (750 lbs). C. Available Cargo Weight = 1 13 kg (250 lbs). Example 3 A. V ehicle Capacity Weight for Example 3 = 453 kg (1,000 lbs).
8-16 Driving and Operating The GVWR includes the weight of the vehicle, all occupants, fuel, and cargo. Never exceed the GVWR for the vehicle, or the Gross Axle Weight Rating (GA WR) for either the front or rear axle. If the vehicle is carrying a heavy load, it should be spread out.
Driving and Operating 8-17 Starting and Operating New V ehicle Break-In Follow these recommended guidelines during the first 2 414 km/1,500 miles of driving this vehicle. Parts have a break-in period and performance will be better in the long run. For the first 2 414 km/1,500 miles: .
8-18 Driving and Operating Ignition Positions (Key Access) The key can be turned to four different positions. T o shift out of P (Park), the ignition must be in the ON/RUN or ACC/ ACCESSORY and the brake pedal must be applied. Notice: Using a tool to force the key from its cylinder could cause damage or break the key .
Driving and Operating 8-19 Ignition Positions (Keyless Access) Y ou can turn the ignition control knob to four different positions. T o shift out of P (Park), ignition must be in the ON/RUN or ACC/ ACCESSORY and the regular brake pedal must be applied.
8-20 Driving and Operating Power to the windows or sunroof will work up to 10 minutes or until any door is opened. For an additional 10 minutes of operation, close all the doors and turn the key to ON/RUN and then back to LOCK/OFF . Starting the Engine Place the transmission in the proper gear .
Driving and Operating 8-21 Starting Procedure 1. With your foot off the accelerator pedal, turn the ignition key to ST ART . If the vehicle has the keyless access system, push the ignition control knob in and rotate the knob to the ST ART position. When the engine starts, let go of the ignition.
8-22 Driving and Operating Engine Coolant Heater V ehicles with the engine coolant heater can use this option in cold weather conditions at or below − 18°C (0°F) for easier starting and better fuel economy during engine warm-up. Plug in the coolant heater at least four hours before starting your vehicle.
Driving and Operating 8-23 2. Move the shift lever into P (Park) by holding in the button on the shift lever and pushing the lever all the way toward the front of the vehicle. 3. T urn the ignition key to LOCK/OFF . 4. For vehicles with key access, remove the key and take it with you.
8-24 Driving and Operating . Prevent movement of the shift lever out of P (Park), unless the ignition is in ON/RUN or ACC/ ACCESSORY and the brake pedal is applied. The shift lock release is always functional except in the case of an uncharged or low voltage (less than 9 volt) battery .
Driving and Operating 8-25 Engine Exhaust { W ARNING Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death.
8-26 Driving and Operating { W ARNING It can be dangerous to get out of the vehicle if the automatic transmission shift lever is not fully in P (Park) with the parking brake firmly set. The vehicle can roll. Do not leave the vehicle when the engine is running unless you have to.
Driving and Operating 8-27 the shift lever button before you can shift from P (Park) when the ignition key is in ON/RUN. If you cannot shift out of P (Park), ease pressure on the shift lever and push the shift lever all the way into P (Park) as you maintain brake application.
8-28 Driving and Operating M (Manual Mode): This position allows the driver to select the range of gears appropriate for current driving conditions. See Driver Shift Control (DSC) later in this section. Notice: Spinning the tires or holding the vehicle in one place on a hill using only the accelerator pedal may damage the transmission.
Driving and Operating 8-29 T o use the DSC feature with the steering wheel paddles (if equipped): 1. Move the shift lever to the right from D (Drive) to M (Manual Mode). 2. The paddles are on the back of the steering wheel. T ap the left paddle to downshift, and the right paddle to upshift.
8-30 Driving and Operating If shifting is prevented for any reason, the currently selected gear will flash multiple times, indicating that the transmission has not shifted gears. While in the DSC mode, the CTS automatic transmission will automatically downshift when the vehicle comes to a stop.
Driving and Operating 8-31 2 (Second): Press the clutch pedal as you let up on the accelerator pedal and shift into 2 (Second). Then, slowly let up on the clutch pedal as you press the accelerator pedal. 3 (Third), 4 (Fourth), 5 (Fifth) and 6 (Sixth): Shift into 3 (Third), 4 (Fourth), 5 (Fifth) and 6 (Sixth) the same way you do for 2 (Second).
8-32 Driving and Operating Up-Shift Light CTS vehicles with a manual transmission have an up-shift light on the instrument panel. This light shows when to shift to the next higher gear for the best fuel economy . When this light comes on, you can shift to the next higher gear if weather , road, and traffic conditions allow .
Driving and Operating 8-33 Brakes Antilock Brake System (ABS) This vehicle has the Antilock Brake System (ABS), an advanced electronic braking system that helps prevent a braking skid. When the engine is started and the vehicle begins to drive away , ABS checks itself.
8-34 Driving and Operating Parking Brake (Manual) The parking brake pedal is located on the lower portion of the instrument panel to the left of the steering wheel. T o set the parking brake, hold the brake pedal down, then push the parking brake pedal down.
Driving and Operating 8-35 Parking Brake (Electric) { W ARNING On vehicles with a manual transmission, releasing the clutch and pressing the accelerator will release the Electric Parking Brake. If the vehicle is not in a gear , the vehicle could move, and you or others could be injured.
8-36 Driving and Operating If the EPB is applied while the vehicle is in motion, a chime will sound, and the DIC message “ Release Park Brake Switch ” will be displayed. The vehicle will decelerate as long as the switch is held in the up position.
Driving and Operating 8-37 Automatic EPB Release The EPB will automatically release if the vehicle is running, placed into gear and an attempt is made to drive away . Avoid rapid acceleration when the EPB is applied, to preserve park brake lining life.
8-38 Driving and Operating The TCS/StabiliT rak warning light flashes when the traction control system is limiting wheel spin. The TCS/StabiliT rak warning light comes on if there is a problem with the traction control system. When the TCS/StabiliT rak warning light is on, the system will not limit wheel spin.
Driving and Operating 8-39 When the system activates, the T raction Control System (TCS)/ StabiliT rak warning light flashes on the instrument panel. A noise may be heard or a vibration may be felt in the brake pedal. This is normal. Continue to steer the vehicle in the intended direction.
8-40 Driving and Operating Competitive Driving Mode Competitive Driving Mode T o select this optional handling mode, press the TCS/StabiliTrak button quickly two times and ST ABILITRAK COMPETITIVE MODE displays in the Driver Information Center (DIC).
Driving and Operating 8-41 The Driver Information Center (DIC) briefly displays SUSPENSION MODE TOURING or SUSPENSION MODE SPORT on vehicle startup or when a new mode is selected. Press and release this button, located in the center of the instrument panel, to change modes.
8-42 Driving and Operating CTS Shown, CTS-V Similar The cruise control buttons are located on the left side of the steering wheel. I (On/Off): Press to turn the system on or off. The indicator light on the button turns on when cruise control is on. + RES (Resume/Accelerate): Press to make the vehicle accelerate or resume to a previously set speed.
Driving and Operating 8-43 The vehicle goes back to the previously set speed and stays there. Increasing Speed While Using Cruise Control T o increase the cruise speed while using cruise control: . Press and hold the +RES button on the steering wheel until the desired speed is reached, then release it.
8-44 Driving and Operating Object Detection Systems Ultrasonic Parking Assist For vehicles with the Ultrasonic Rear Parking Assist (URP A) system, it assists the driver with parking and avoiding objects while in R (Reverse). URP A operates at speeds less than 8 km/h (5 mph), and the sensors on the rear bumper detect objects up to 2.
Driving and Operating 8-45 How the System Works URP A comes on automatically and the display briefly illuminates to indicate the system is working when the shift lever is moved into R (Reverse). If the vehicle is traveling faster then 8 km/h (5 mph) in reverse, the red light on the rear display flashes.
8-46 Driving and Operating When the System Does Not Seem to Work Properly If the URP A system will not activate due to a temporary condition, the message P ARK ASSIST OFF will be displayed on the DIC and a red light will be shown on the rear URP A display when the shift lever is moved into R (Reverse).
Driving and Operating 8-47 W ARNING (Continued) speed backing maneuvers or where there could be cross-traffic. Y our judged distances using the screen will differ from actual distances. So if you do not use proper care before backing up, you could hit a vehicle, child, pedestrian, bicyclist, or pet, resulting in vehicle damage, injury , or death.
8-48 Driving and Operating The area displayed by the camera is limited and does not display objects that are close to either corner or under the bumper . The area displayed can vary depending on vehicle orientation or road conditions. The distance of the image that appears on the screen differs from the actual distance.
Driving and Operating 8-49 Fuel Use of the recommended fuel is an important part of the proper maintenance of this vehicle. T o help keep the engine clean and maintain optimum vehicle performance, we recommend the use of gasoline advertised as TOP TIER Detergent Gasoline.
8-50 Driving and Operating unleaded gasoline with an octane rating of 87 or higher . If 87 octane fuel is used, do not perform any aggressive driving maneuvers such as wide open throttle applications. Y ou might also hear audible spark knock during acceleration.
Driving and Operating 8-51 However , some gasolines contain only the minimum amount of additive required to meet U.S. Environmental Protection Agency regulations.
8-52 Driving and Operating Filling the T ank { W ARNING Fuel vapor burns violently and a fuel fire can cause bad injuries. T o help avoid injuries to you and others, read and follow all the instructions on the fuel pump island. T urn off the engine when refueling.
Driving and Operating 8-53 The diagnostic system can determine if the fuel cap has been left off or improperly installed. This would allow fuel to evaporate into the atmosphere. See Malfunction Indicator Lamp on page 4 ‑ 23 . { W ARNING If a fire starts while you are refueling, do not remove the nozzle.
8-54 Driving and Operating T owing General T owing Information Only use towing equipment that has been designed for the vehicle. Contact your dealer/retailer or trailering retailer for assistance with preparing the vehicle for towing a trailer . See the following trailer towing information in this section: .
Driving and Operating 8-55 Pulling A T railer Here are some important points: . There are many laws, including speed limit restrictions that apply to trailering. Check for legal requirements with state or provincial police. . Do not tow a trailer at all during the first 1 600 km (1,000 miles) the new vehicle is driven.
8-56 Driving and Operating Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving the vehicle without a trailer . This can help to avoid situations that require heavy braking and sudden turns. Passing More passing distance is needed when towing a trailer .
Driving and Operating 8-57 When towing at high altitude on steep uphill grades, consider the following: Engine coolant will boil at a lower temperature than at normal altitudes. If the engine is turned off immediately after towing at high altitude on steep uphill grades, the vehicle may show signs similar to engine overheating.
8-58 Driving and Operating Maintenance When T railer T owing The vehicle needs service more often when pulling a trailer . See this manual's Maintenance Schedule or Index for more information.
Driving and Operating 8-59 the vehicle, it will reduce the tongue weight the vehicle can carry , which will also reduce the trailer weight the vehicle can tow . If towing a trailer , the tongue load must be added to the GVW because the vehicle will be carrying that weight, too.
8-60 Driving and Operating Safety Chains Always attach chains between the vehicle and the trailer . Cross the safety chains under the tongue of the trailer to help prevent the tongue from contacting the road if it becomes separated from the hitch. Leave enough slack so the rig can turn.
V ehicle Care 9-1 V ehicle Care General Information General Information . . . . . . . . . . . 9-2 California Proposition 65 Warning . . . . . . . . . . . . . . . . . . 9-3 California Perchlorate Materials Requirements . . . . . . . . . . . . . . . 9-3 Accessories and Modifications .
9-2 V ehicle Care Wheels and Tires T ires . . . . . . . . . . . . . . . . . . . . . . . . . 9-58 Winter Tires . . . . . . . . . . . . . . . . . . 9-59 Low-Profile Tires . . . . . . . . . . . . . 9-59 T ire Sidewall Labeling . . . . . . . 9-60 T ire Designations .
V ehicle Care 9-3 California Proposition 65 W arning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems, many fluids, and some component wear by-products contain and/or emit these chemicals.
9-4 V ehicle Care V ehicle Checks Doing Y our Own Service Work { W ARNING Y ou can be injured and the vehicle could be damaged if you try to do service work on a vehicle without knowing enough about it. . Be sure you have sufficient knowledge, experience, the proper replacement parts, and tools before attempting any vehicle maintenance task.
V ehicle Care 9-5 Hood T o open the hood: 1. Pull the hood release lever with this symbol on it. It is located inside the vehicle on the lower left side of the instrument panel. 2. Then go to the front of the vehicle and find the secondary hood release lever .
9-6 V ehicle Care Engine Compartment Overview CTS 3.6 L V6 Engine shown, 3.0 L V6 Engine similar.
V ehicle Care 9-7 A. Windshield Washer Fluid Reservoir . See Washer Fluid on page 9 ‑ 25 . B. Engine Compartment Fuse Block (CTS) on page 9 ‑ 41 or Engine Compartment Fuse Block (CTS-V) on page 9 ‑ 45 or Engine Compartment Fuse Block (CTS Wagon) on page 9 ‑ 48 .
9-8 V ehicle Care CTS-V 6.2 L V8 Engine.
V ehicle Care 9-9 A. Windshield Washer Fluid Reservoir . See Washer Fluid on page 9 ‑ 25 . B. Engine Compartment Fuse Block (CTS) on page 9 ‑ 41 or Engine Compartment Fuse Block (CTS-V) on page 9 ‑ 45 or Engine Compartment Fuse Block (CTS Wagon) on page 9 ‑ 48 .
9-10 V ehicle Care 4. Lift and remove the engine cover . 5. Reverse Steps 1 through 4 to reinstall engine cover . Engine Cover (CTS-V) T o remove: The engine cover consists of two pieces. Only the larger front piece needs to be removed to access the engine oil and power steering fill caps.
V ehicle Care 9-1 1 Notice: Do not add too much oil. If the engine has so much oil that the oil level gets above the cross-hatched area that shows the proper operating range, the engine could be damaged. See Engine Compartment Overview on page 9 ‑ 6 for the location of the engine oil fill cap.
9-12 V ehicle Care Substitute Engine Oil: When adding oil to maintain engine oil level, oil meeting GM Standard GM4718M might not be available. Y ou can add substitute oil designated SAE 5W-30 with the starburst symbol at all temperatures. Substitute oil not meeting GM Standard GM4718M should not be used for an oil change.
V ehicle Care 9-13 How to Reset the Engine Oil Life System Reset the system whenever the engine oil is changed so that the system can calculate the next engine oil change. T o reset the system: 1. T urn the ignition to ON/RUN with the engine off. 2. Fully press and release the accelerator pedal three times within five seconds.
9-14 V ehicle Care Change the fluid and filter at the intervals listed in Scheduled Maintenance on page 10 ‑ 3 , and be sure to use the fluid listed in Recommended Fluids and Lubricants on page 10 ‑ 7 . Manual T ransmission Fluid It is not necessary to check the manual transmission fluid level.
V ehicle Care 9-15 Engine Air Cleaner/Filter The engine air cleaner/filter is in the engine compartment on the driver side of the vehicle, near the front.
9-16 V ehicle Care 6. Remove the three air cleaner housing cover screws. 7. Move the air cleaner housing cover and remove the cover from the air cleaner housing.
V ehicle Care 9-17 How to Reinstall Engine Air Cleaner/Filter 1. Install the air cleaner into the air cleaner housing. The outer air cleaner filter seal must be fitted properly in the air cleaner housing. 2. Align the air cleaner housing cover tabs to the air cleaner housing.
9-18 V ehicle Care Cooling System The cooling system allows the engine to maintain the correct working temperature. When you decide it is safe to lift the hood, here is what you will see: A.
V ehicle Care 9-19 What to Use { W ARNING Adding only plain water to the cooling system can be dangerous. Plain water , or some other liquid such as alcohol, can boil before the proper coolant mixture will. The vehicle's coolant warning system is set for the proper coolant mixture.
9-20 V ehicle Care If the engine is warm or hot, the coolant level should be at or above the FROID/FULL COLD line on the side of the coolant surge tank. If the engine is cold, the coolant level should be near the FROID/FULL COLD line on the side of the coolant surge tank.
V ehicle Care 9-21 2. Then keep turning the pressure cap slowly and remove it. 3. Fill the coolant surge tank with the proper mixture, to slightly above the FROID/FULL COLD line on the side of the coolant surge tank.
9-22 V ehicle Care Checking Coolant in the Intercooler System (CTS-V) The vehicle must be on a level surface when checking the coolant level. The super charged engine intercooler coolant fill neck is located in the engine compartment on the passenger side of the vehicle.
V ehicle Care 9-23 Notice: If the pressure cap is not tightly installed, coolant loss and possible engine damage may occur . Be sure the cap is properly and tightly secured. If the coolant is not at the proper level when the system cools down again, see your dealer/retailer .
9-24 V ehicle Care If No Steam Is Coming From The Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: . Climbs a long hill on a hot day .
V ehicle Care 9-25 Power Steering Fluid See Engine Compartment Overview on page 9 ‑ 6 for the location of the power steering fluid reservoir . When to Check Power Steering Fluid It is not necessary to regularly check power steering fluid unless you suspect there is a leak in the system or you hear an unusual noise.
9-26 V ehicle Care Adding W asher Fluid The W asher Fluid Low Add Fluid message will appear on the Driver Information Center (DIC) when the fluid level is low . See Driver Information Center (DIC) on page 4 ‑ 31 for more information. Open the cap with the washer symbol on it.
V ehicle Care 9-27 Some driving conditions or climates can cause a brake squeal when the brakes are first applied or lightly applied. This does not mean something is wrong with the brakes. Properly torqued wheel nuts are necessary to help prevent brake pulsation.
9-28 V ehicle Care . A fluid leak in the brake hydraulic system can also cause a low fluid level. Have the brake hydraulic system fixed, since a leak means that sooner or later the brakes will not work well. Do not top off the brake fluid. Adding fluid does not correct a leak.
V ehicle Care 9-29 Battery The battery is in the trunk, behind the trim panel, on the passenger side of the vehicle. Refer to the replacement number shown on the original battery label when a new battery is needed.
9-30 V ehicle Care All-Wheel Drive If your vehicle is equipped with all-wheel-drive, this is an additional system that needs lubrication. T ransfer Case When to Check Lubricant It is not necessary to regularly check the transfer case fluid unless you suspect there is a leak or you hear an unusual noise.
V ehicle Care 9-31 How to Check Lubricant T o get an accurate reading, the vehicle should be on a level surface. If the level is below the bottom of the filler plug hole, located on the rear axle, you'll need to add some lubricant. Add enough lubricant to raise the level to the bottom of the filler plug hole.
9-32 V ehicle Care Automatic T ransmission Shift Lock Control System Check { W ARNING When you are doing this inspection, the vehicle could move suddenly . If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle.
V ehicle Care 9-33 Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake. . T o check the parking brake's holding ability: With the engine running and the transmission in N (Neutral), slowly remove foot pressure from the regular brake pedal.
9-34 V ehicle Care 6. Replace the blade with a new one. 7. Reinstall the wiper blade assembly by sliding it over the wiper arm to engage the J-hooked end. Pull up on the assembly to lock it into place. 8. Repeat the steps for the other wiper . Headlamp Aiming The vehicle has a visual optical headlamp aiming system.
V ehicle Care 9-35 T o adjust the vertical aim: 1. Open the hood. See Hood on page 9 ‑ 5 for more information. Halogen Headlamps High Intensity Discharge Headlamps 2. Locate the aim dot on the lens of the low-beam headlamp. 3. Record the distance from the ground to the aim dot on the low-beam headlamp.
9-36 V ehicle Care Notice: Do not cover a headlamp to improve beam cut-off when aiming. Covering a headlamp may cause excessive heat build-up which may cause damage to the headlamp. 6. T urn on the low-beam headlamps and place a piece of cardboard or equivalent in front of the headlamp not being aimed.
V ehicle Care 9-37 Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 9 ‑ 39 . For any bulb changing procedure not listed in this section, contact your dealer/retailer . Halogen Bulbs { W ARNING Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb.
9-38 V ehicle Care 4. Remove the bulb socket from the lamp housing by turning the bulb socket one-quarter turn counterclockwise. 5. Pull the old bulb from the lamp housing keeping the bulb straight as you pull it out. 6. Install a new bulb. 7. Reinstall the electrical connector by pushing in the two plastic clips.
V ehicle Care 9-39 License Plate Lamp (W agon) T o replace one of these bulbs: 1. Open the liftgate. See Liftgate (Wagon) on page 1 ‑ 19 for more information. Passenger side shown, driver side similar 2. Push the left end of the lamp assembly towards the right.
9-40 V ehicle Care Electrical System Electrical System Overload The vehicle has fuses and circuit breakers to protect against an electrical system overload. When the current electrical load is too heavy , the circuit breaker opens and closes, protecting the circuit until the current load returns to normal or the problem is fixed.
V ehicle Care 9-41 Fuses and Circuit Breakers The wiring circuits in the vehicle are protected from short circuits by a combination of fuses and circuit breakers. This greatly reduces the chance of damage caused by electrical problems. T o check a fuse, look at the silver-colored band inside the fuse.
9-42 V ehicle Care Mini-Fuses Usage A/C CL TCH Air Conditioning Clutch ABS Antilock Braking System (ABS) AFS Adaptive Forward Lighting System Mini-Fuses Usage AIRBAG IGN Airbag Switch AQS/ ISRVM/ REAR.
V ehicle Care 9-43 Mini-Fuses Usage DRL/WSW Daytime Running Lamps/Windshield W asher Pump ECM Engine Control Module (ECM) ECM/ TCM IGN ECM, T ransmission Control Module (TCM), Instrument Panel Cluster.
9-44 V ehicle Care J-Case Fuses Usage F AN 1 Cooling Fan 1 F AN 2 Cooling Fan 2 REAR DEFOG Rear Defogger STRTR Starter SP ARE Spare WSW/HTR Not Used Relays Usage A/C CMPRSR Air Conditioning Compressor.
V ehicle Care 9-45 Engine Compartment Fuse Block (CTS-V) The underhood fuse block is located on the passenger side of the engine compartment. Lift the fuse block cover to access the fuses. Notice: Spilling liquid on any electrical components on the vehicle may damage it.
9-46 V ehicle Care Mini-Fuses Usage BCM 2 Body Control Module 2 BCM 3 Body Control Module 3 BCM 4 Body Control Module 4 BCM 5 Body Control Module 5 BCM 6, BCM 7 Body Control Module 6 and 7 DISPL Y Dis.
V ehicle Care 9-47 J-Case Fuses Usage ABS MTR ABS Motor BL WR Blower EPB Electric Park Brake F AN 1 Cooling Fan 1 F AN 2 Cooling Fan 2 MRTD MR Ride/ Suspension Control REAR DEFOG Rear Defogger STRTR S.
9-48 V ehicle Care Engine Compartment Fuse Block (CTS W agon) The underhood fuse block is located on the passenger side of the engine compartment. Lift the fuse block cover to access the fuses. Notice: Spilling liquid on any electrical components on the vehicle may damage it.
V ehicle Care 9-49 Mini-Fuses Usage A WD All-Wheel Drive BCM 1 Body Control Module 1 BCM 2 Body Control Module 2 BCM 3 Body Control Module 3 BCM 4 Body Control Module 4 BCM 5 Body Control Module 5 BCM.
9-50 V ehicle Care Mini-Fuses Usage PWR MODING PassKey Module, Body Control Module PWR OUTLET Console Auxiliary Power Outlet RT HI BEAM Right High-Beam Headlamp RT LO BEAM Right Low-Beam Headlamp RT L.
V ehicle Care 9-51 Relays Usage LO BEAM (W/O HID) L T DRL (HID) Low-Beam (without High Intensity Discharge), Left Daytime Running Lamp (High Intensity Discharge) PWR/TRN Powertrain REAR DEFOG Rear Def.
9-52 V ehicle Care Relays Usage REAR/FOG Not Used RT/POS/LP Not Used STOP/LP Not Used TRUNK/ RELSE T runk Release UNLCK Unlock Mini-Fuses Usage AIRBAG Airbag System AMP Amplifier AUX/ OUTLET Auxiliary.
V ehicle Care 9-53 Circuit Breakers Usage DRV/ PWR/SEA T Left Front Power Seat L T/ REAR/ WNDW Left Rear Window PWR CLMN Power Steering Column PWR/ WNDW Power Window P ASS/ PWR/SEA T Right Front Power.
9-54 V ehicle Care Relays Usage REAR/FOG Not Used RT/POS/LP Not Used STOP/LP Not Used TRUNK/ RELSE T runk Release UNLCK Unlock Mini-Fuses Usage AIRBAG Airbag System AMP Amplifier AUX/ OUTLET Auxiliary.
V ehicle Care 9-55 Circuit Breakers Usage DRV/ PWR/SEA T Left Front Power Seat L T/ REAR/ WNDW Left Rear Window P ASS/ PWR/SEA T Right Front Power Seat PWR CLMN Power Steering Column PWR/ WNDW Power W.
9-56 V ehicle Care Relays Usage REAR/FOG Not Used RT/POS/LP Not Used STOP/LP Not Used TRUNK/ RELSE T runk Release UNLCK Unlock Mini-Fuses Usage AIRBAG Airbag System AMP Amplifier Mini-Fuses Usage AUX/.
V ehicle Care 9-57 Mini-Fuses Usage RKE/ P ASS-KEY/ MDL Remote Keyless Entry System, Pass-Key Theft Deterrent Feature Module RT/POS/LP Not Used RT/POS/LP Right Position Lamp RVC/SNSR Regulated V oltag.
9-58 V ehicle Care Wheels and Tires Tires Y our new vehicle comes with high-quality tires made by a leading tire manufacturer . If you ever have questions about your tire warranty and where to obtain service, see your vehicle W arranty booklet for details.
V ehicle Care 9-59 Winter Tires If you expect to drive on snow or ice covered roads often, you may want to get winter tires for your vehicle. All season tires provide good overall performance on most surfaces but they may not offer the traction you would like or the same level of performance as winter tires on snow or ice covered roads.
9-60 V ehicle Care Summer Performance Tires Many General Motors high performance models come factory-equipped with tires that are optimized for maximum dry and wet road performance while still retaining satisfactory tread life, excellent durability , and low noise levels.
V ehicle Care 9-61 The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture. (E) Tire Ply Material : The type of cord and number of plies in the sidewall and under the tread.
9-62 V ehicle Care (E) Tire Inflation : The temporary use tire or compact spare tire should be inflated to 420 kPa (60 psi). For more information on tire pressure and inflation see Tire Pressure on page 9 ‑ 66 .
V ehicle Care 9-63 (E) Rim Diameter : Diameter of the wheel in inches. (F) Service Description : These characters represent the load index and speed rating of the tire. The load index represents the load carry capacity a tire is certified to carry . The speed rating is the maximum speed a tire is certified to carry a load.
9-64 V ehicle Care GA WR FRT : Gross Axle Weight Rating for the front axle. See V ehicle Load Limits on page 8 ‑ 12 . GA WR RR : Gross Axle Weight Rating for the rear axle. See V ehicle Load Limits on page 8 ‑ 12 . Intended Outboard Sidewall : The side of an asymmetrica l tire, that must always face outward when mounted on a vehicle.
V ehicle Care 9-65 Radial Ply Tire : A pneumatic tire in which the ply cords that extend to the beads are laid at 90 degrees to the centerline of the tread. Rim : A metal support for a tire and upon which the tire beads are seated. Sidewall : The portion of a tire between the tread and the bead.
9-66 V ehicle Care Tire Pressure T ires need the correct amount of air pressure to operate effectively . Notice: Do not let anyone tell you that under-inflation or over-inflation is all right. It is not. If your tires do not have enough air (under-inflation), you can get the following: .
V ehicle Care 9-67 How to Check Use a good quality pocket-type gage to check tire pressure. Y ou cannot tell if your tires are properly inflated simply by looking at them. Radial tires may look properly inflated even when they are under-inflated. Check the tire's inflation pressure when the tires are cold.
9-68 V ehicle Care When you end this high-speed driving, return the tires to the cold tire inflation pressure shown on the T ire and Loading Information label.
V ehicle Care 9-69 Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.
9-70 V ehicle Care When a low tire pressure condition is detected, the TPMS illuminates the low tire pressure warning light located on the instrument panel cluster . A DIC warning message to check the pressure in a specific tire is also shown on the DIC display screen.
V ehicle Care 9-71 TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle.
9-72 V ehicle Care The TPMS sensors can also be matched to each tire/wheel position by increasing or decreasing the tire's air pressure. If increasing the tire's air pressure, do not exceed the maximum inflation pressure indicated on the tire's sidewall.
V ehicle Care 9-73 Tire Inspection We recommend that you regularly inspect your vehicle's tires, including the spare tire, if the vehicle has one, for signs of wear or damage. See When It Is Time for New Tires on page 9 ‑ 74 for more information.
9-74 V ehicle Care After the tires have been rotated, adjust the front and rear inflation pressures as shown on the Tire and Loading Information label. See Tire Pressure on page 9 ‑ 66 and V ehicle Load Limits on page 8 ‑ 12 . Reset the Tire Pressure Monitor System.
V ehicle Care 9-75 The vehicle needs new tires if any of the following statements are true: . Y ou can see the indicators at three or more places around the tire. . Y ou can see cord or fabric showing through the tire's rubber . . The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric.
9-76 V ehicle Care GM's exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of your vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance.
V ehicle Care 9-77 { W ARNING If you use bias-ply tires on the vehicle, the wheel rim flanges could develop cracks after many miles of driving. A tire and/or wheel could fail suddenly , causing a crash. Use only radial-ply tires with the wheels on the vehicle.
9-78 V ehicle Care Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width.
V ehicle Care 9-79 T raction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete.
9-80 V ehicle Care Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air , replace it (except some aluminum wheels, which can sometimes be repaired).
V ehicle Care 9-81 Tire Chains { W ARNING Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts.
9-82 V ehicle Care A rear blowout, particularly on a curve, acts much like a skid and may require the same correction you would use in a skid. In any rear blowout remove your foot from the accelerator pedal. Get the vehicle under control by steering the way you want the vehicle to go.
V ehicle Care 9-83 W ARNING (Continued) 3. T urn off the engine and do not restart while the vehicle is raised. 4. Do not allow passengers to remain in the vehicle. T o be certain the vehicle will not move, put blocks at the front and rear of the tire farthest away from the one being changed.
9-84 V ehicle Care Tire Sealant and Compressor Kit { W ARNING Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death.
V ehicle Care 9-85 This vehicle may have one of the following tire sealant and compressor kits. The kit includes: A. Selector Switch (Sealant/Air or Air Only) B. On/Off Button C. Pressure Gage D. Pressure Deflation Button (If equipped) E. Tire Sealant Canister F .
9-86 V ehicle Care Using the Tire Sealant and Compressor Kit to T emporarily Seal and Inflate a Punctured Tire Follow the directions closely for correct sealant usage. When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for 5 minutes.
V ehicle Care 9-87 Always do a safety check first. See If a Tire Goes Flat on page 9 ‑ 81 . Do not remove any objects that have penetrated the tire. 1.
9-88 V ehicle Care 10. Inflate the tire to the recommended inflation pressure using the pressure gage (C). The recommended inflation pressure can be found on the T ire and Loading Information label. See Tire Pressure on page 9 ‑ 66 . The pressure gage (C) may read higher than the actual tire pressure while the compressor is on.
V ehicle Care 9-89 16. If the flat tire was able to inflate to the recommended inflation pressure, remove the maximum speed label from the sealant canister (E) and place it in a highly visible location. The label is a reminder not to exceed 90 km/h (55 mph) until the damaged tire is repaired or replaced.
9-90 V ehicle Care Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured) T o use the air compressor to inflate a tire with air only and not sealant: Always do a safety check first. See If a Tire Goes Flat on page 9 ‑ 81 .
V ehicle Care 9-91 3. Place the kit on the ground. Make sure the tire valve stem is positioned close to the ground so the hose will reach it. 4. Remove the tire valve stem cap from the flat tire by turning it counterclockwise. 5. Attach the air only hose (G) onto the tire valve stem by turning it clockwise until it is tight.
9-92 V ehicle Care 14. Replace the air only hose (G) and the power plug (H) and cord back in its original location. 15. Place the equipment in the original storage location in the vehicle.
V ehicle Care 9-93 4. Remove the tire sealant and compressor kit (A) from the foam container (B). Tire Sealant and Compressor Kit with Pressure Deflation Button 1. Open the trunk. See T runk (Sedan) on page 1 ‑ 17 . 2. Remove the retainer that holds the tire sealant and compressor kit in place.
9-94 V ehicle Care Tire Changing Removing the Spare Tire and T ools (Sedan) Sedan A. Wing Nut B. Spare Tire C. Jack D. Wheel Wrench E. Extension F . Strap T o access the spare tire and jacking equipment: 1. Remove the spare tire cover . 2. Remove the stow rod cap by pulling it straight up off of the rod.
V ehicle Care 9-95 A. Wing Nut B. Spare Tire C. Jack D. Subwoofer E. Wheel Wrench F . Extension G. Cable T o access the spare tire and jacking equipment: 1. Remove the spare tire cover . 2. Remove the subwoofer (D), if the vehicle has one. T o remove the subwoofer: 2.
9-96 V ehicle Care Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before proceeding. See If a Tire Goes Flat on page 9 ‑ 81 for more information. 2. Loosen the wheel nuts, but do not remove them yet, using the wheel wrench.
V ehicle Care 9-97 { W ARNING Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for changing a flat tire.
9-98 V ehicle Care 9. Remove all the wheel nuts and the flat tire. { W ARNING Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time.
V ehicle Care 9-99 13. T ighten each wheel nut by turning it clockwise with your hand until the wheel is held against the hub. 14. Lower the vehicle by turning the wheel wrench counterclockwise. Lower the jack completely . { W ARNING Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off.
9-100 V ehicle Care 4. Route the loop end of the strap (C) through one of the cargo tie-downs (A) located in the rear of the vehicle. 5. Route the hook (B) through the loop (C). 6. Pull the strap to tighten it around the cargo tie-down (A). 7. Route the hook end of the strap through the wheel.
V ehicle Care 9-101 5. Slide both D-rings (E) on each side of the vehicle as far rearward as they will go. 6. Route one hook (A) under the wheel spoke (C) and place the hook into the slot in the cargo rail on the driver side of the vehicle. 7. Slide the D-ring (E) on that side forward to engage the hook.
9-102 V ehicle Care Compact Spare Tire and T ools (W agon) Use the following diagram as a guide for storing the compact spare tire and tools in the rear compartment area: A.
V ehicle Care 9-103 convenience. Of course, it is best to replace the spare with a full-size tire as soon as possible. The spare tire will last longer and be in good shape in case it is needed again. Notice: When the compact spare is installed, do not take the vehicle through an automatic car wash with guide rails.
9-104 V ehicle Care 2. Get the vehicles close enough so the jumper cables can reach, but be sure the vehicles are not touching each other . If they are, it could cause a ground connection you do not want. Y ou would not be able to start your vehicle and the bad grounding could damage the electrical systems.
V ehicle Care 9-105 Notice: If you connect a negative cable to the Engine Control Module (ECM), ECM mounting bracket, or any cables that attach to the ECM bracket, you may damage the ECM.
9-106 V ehicle Care Do not connect positive (+) to negative ( − ) or you will get a short that would damage the battery and maybe other parts too. And do not connect the negative ( − ) cable to the negative ( − ) terminal on the dead battery because this can cause sparks.
V ehicle Care 9-107 Notice: If the jumper cables are connected or removed in the wrong order , electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty . Always connect and remove the jumper cables in the correct order , making sure that the cables do not touch each other or other metal.
9-108 V ehicle Care T owing T owing the V ehicle Consult your dealer/retailer or a professional towing service if the disabled vehicle needs to be towed. See Roadside Service on page 12 ‑ 6 . T o tow the vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see Recreational V ehicle T owing following.
V ehicle Care 9-109 Notice: If the vehicle is towed with all four wheels on the ground, the drivetrain components could be damaged. The repairs would not be covered by the vehicle warranty . Do not tow the vehicle with all four wheels on the ground. The vehicle was not designed to be towed with all four wheels on the ground.
9-1 10 V ehicle Care Dolly T owing (All-Wheel-Drive V ehicles) Notice: T owing an all-wheel-drive vehicle with all four wheels on the ground, or even with only two of its wheels on the ground, will damage drivetrain components. Do not tow an all-wheel-drive vehicle with any of its wheels on the ground.
V ehicle Care 9-1 1 1 Notice: Machine compounding or aggressive polishing on a basecoat/clearcoat paint finish may damage it. Use only non-abrasive waxes and polishes that are made for a basecoat/clearcoat paint finish on the vehicle.
9-1 12 V ehicle Care Rinse the vehicle well, before washing and after to remove all cleaning agents completely . If they are allowed to dry on the surface, they could stain. Dry the finish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting.
V ehicle Care 9-1 13 The surface of these wheels is similar to the painted surface of the vehicle. Do not use strong soaps, chemicals, abrasive polishes, abrasive cleaners, cleaners with acid, or abrasive cleaning brushes on them because the surface could be damaged.
9-1 14 V ehicle Care Finish Damage Any stone chips, fractures or deep scratches in the finish should be repaired right away . Bare metal will corrode quickly and may develop into major repair expense. Minor chips and scratches can be repaired with touch-up materials available from your dealer/retailer .
V ehicle Care 9-1 15 Y our dealer/retailer has products for cleaning the vehicle's interior . When cleaning the vehicle's interior , only use cleaners specifically designed for the surfaces that are being cleaned. Permanent damage can result from using cleaners on surfaces for which they were not intended.
9-1 16 V ehicle Care Fabric/Carpet Use a vacuum cleaner with a soft brush attachment to remove dust and loose dirt. A canister vacuum with a beater bar in the nozzle may only be used on floor carpet and carpeted floor mats. For soils, always try to remove them first with plain water or club soda.
V ehicle Care 9-1 17 Instrument Panel, Vinyl, and Other Plastic Surfaces T o remove dust, a soft cloth dampened with water can be used. If a more thorough cleaning is necessary , a clean soft cloth dampened with a mild soap solution can be used to gently remove dust and dirt.
9-1 18 V ehicle Care 2 NOTES.
Service and Maintenance 10-1 Service and Maintenance General Information General Information . . . . . . . . . . 10-1 Scheduled Maintenance Scheduled Maintenance . . . . . 10-3 Recommended Fluids, Lubricants, and Parts Recommended Fluids and Lubricants .
10-2 Service and Maintenance { W ARNING Performing maintenance work can be dangerous. Some jobs can cause serious injury . Perform maintenance work only if you have the required know-how and the proper tools and equipment. If in doubt, see your dealer/retailer to have a qualified technician do the work.
Service and Maintenance 10-3 Scheduled Maintenance When the Change Engine Oil Soon Message Displays Change engine oil and filter . See Engine Oil on page 9 ‑ 10 . An Emission Control Service. When the “ Change Engine Oil Soon ” message displays, service is required for the vehicle as soon as possible, within the next 1 000 km/ 600 miles.
10-4 Service and Maintenance . Brake system inspection (or every 12 months, whichever occurs first). . Steering and suspension inspection. Visual inspection for damaged, loose, or missing parts or signs of wear . . Body hinges and latches, key lock cylinders, folding seat hardware, and sunroof (if equipped) lubrication.
Service and Maintenance 10-5 First Engine Oil Change After Every 40 000 km/25,000 Miles . Fuel system inspection for damage or leaks. . Passenger compartment air filter replacement (or every 12 months, whichever occurs first). More frequent replacement may be required if vehicle is driven regularly under dusty conditions.
10-6 Service and Maintenance . CTS-V only: Rear axle fluid change (severe service only) for vehicles mainly driven in hilly or mountainous terrain, when frequently towing a trailer , used for high speed or competitive driving, or used for taxi, police, or delivery service.
Service and Maintenance 10-7 Recommended Fluids, Lubricants, and Parts Recommended Fluids and Lubricants Usage Fluid/Lubricant Engine Oil The engine requires a special engine oil meeting GM Standard GM4718M. Oils meeting this standard can be identified with the American Petroleum Institute (API) Certified for Gasoline Engines starburst symbol.
10-8 Service and Maintenance Usage Fluid/Lubricant Manual Transmission (CTS-V) Manual Transmission Fluid (GM Part No. U.S. 88861800, in Canada 88861801). Automatic Transmission DEXRON ® -VI Automatic Transmission Fluid. Rear Drive Module and T ransfer Case (All-Wheel Drive) T ransfer Case Fluid (GM Part No.
Service and Maintenance 10-9 Maintenance Replacement Parts Replacement parts identified below by name, part number , or specification can be obtained from your retailer . Part GM Part Number ACDelco Part Number Engine Air Cleaner/Filter 3.0L V6 Engine 15875795 A3096C 3.
10-10 Service and Maintenance Part GM Part Number ACDelco Part Number Wiper Blades — Except CTS-V Driver Side – 56.5 cm (22 in) 15890062 — Passenger Side – 53.3 cm (21 in) 15890064 — Wiper Blades — CTS-V Driver Side – 56.5 cm (22 in) 20791461 — Passenger Side – 53.
Service and Maintenance 10-1 1 Maintenance Records After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided.
10-12 Service and Maintenance Maintenance Record (cont'd) Date Odometer Reading Serviced By Maintenance Stamp Services Performed.
Service and Maintenance 10-13 Maintenance Record (cont'd) Date Odometer Reading Serviced By Maintenance Stamp Services Performed.
10-14 Service and Maintenance Maintenance Record (cont'd) Date Odometer Reading Serviced By Maintenance Stamp Services Performed.
T echnical Data 1 1-1 T echnical Data V ehicle Identification V ehicle Identification Number (VIN) . . . . . . . . . . . . . . 1 1-1 Service Parts Identification L a b e l ....................... 1 1 - 1 V ehicle Data Capacities and Specifications . .
1 1-2 T echnical Data V ehicle Data Capacities and Specifications The following approximate capacities are given in metric and English conversions. See Recommended Fluids and Lubricants on page 10 ‑ 7 for more information.
T echnical Data 1 1-3 Application Capacities Metric English Fuel T ank 68.1 L 18.0 gal T ransfer Case — AWD 1.0 L 1.1 qt T ransmission Fluid (Pan Removal and Filter Replacement) 3.0L V6 Engine, 6-Speed Automatic 6.3 L 6.7 qt 3.6L V6 Engine, 6-Speed Automatic 6.
1 1-4 T echnical Data Engine Specifications Engine VIN Code T ransmission Spark Plug Gap 3.0L V6 Engine G Automatic Manual 1.1 mm (0.043 in) 3.6L V6 Engine V Automatic Manual 1.1 mm (0.043 in) 6.2L V8 Engine P Automatic Manual 1.0 mm (0.040 in) Engine Drive Belt Routing CTS 3.
Customer Information 12-1 Customer Information Customer Information Customer Satisfaction Procedure . . . . . . . . . . . . . . . . . . 12-1 Customer Assistance Offices . . . . . . . . . . . . . . . . . . . . . 12-3 Customer Assistance for T ext T elephone (TTY) Users .
12-2 Customer Information STEP TWO: If after contacting a member of dealership management, it appears your concern cannot be resolved by the dealership without further help, in the United States, call the Cadillac Customer Assistance Center , 24 hours a day , at 1-800-458-8006.
Customer Information 12-3 STEP THREE (Canadian Owners): General Motors Participation in the Mediation/Arbitration Program In the event that you do not feel your concerns have been addressed after the following the procedure outlined in Steps One and T wo.
12-4 Customer Information From Puerto Rico: 1-800-496-9992 (English) 1-800-496-9993 (Spanish) From U.S. Virgin Islands: 1-800-496-9994 Canada — Customer Assistance General Motors of Canada Limited Canadian Cadillac Customer Communication Centre, CA1-163-005 1908 Colonel Sam Drive Oshawa, Ontario L1H 8P7 www .
Customer Information 12-5 Other Helpful Links: Cadillac — www .cadillac.com Cadillac Merchandise — www .cadillaccollection.com Help Center — www .cadillac.com/ helpcenter . F AQ . Contact Us My GM Canada (Canada) — www.gm.ca My GM Canada is a password-protected section of www .
12-6 Customer Information Roadside Service In the United States or Canada, call 1-800-882-1 1 12 . T ext T elephone (TTY), U.S. only , call 1-888-889-2438 . Service is available 24 hours a day , 365 days a year. Calling for Assistance When calling Roadside Assistance, have the following information ready: .
Customer Information 12-7 It is your responsibility for the repair or replacement of the tire if it is not covered by the warranty . . Battery Jump Start: Service is provided to jump start a dead battery . . T rip Routing Service: Detailed maps of North America are provided when requested either with the most direct route or the most scenic route.
12-8 Customer Information . T rip Interruption Benefits and Assistance: Pre-authorization, original detailed receipts, and a copy of the repair orders are required. Once authorization has been received, the Roadside Assistance advisor will help you make arrangements and explain how to receive payment.
Customer Information 12-9 T ransportation Options W arranty service can generally be completed while you wait. However , if you are unable to wait, GM helps to minimize your inconvenience by providing several transportation options.
12-10 Customer Information Additional Program Information All program options, such as shuttle service, may not be available at every dealer . Please contact your dealer for specific information about availability . All Courtesy T ransportation arrangements will be administered by appropriate dealer personnel.
Customer Information 12-1 1 Aftermarket parts are not covered by your GM New V ehicle Limited W arranty , and any vehicle failure related to such parts are not covered by that warranty . Repair Facility We recommend that you choose a collision repair facility that meets your needs before you ever need collision repairs.
12-12 Customer Information . V ehicle Identification Number (VIN) . Insurance company and policy number . General description of the damage to the other vehicle Choose a reputable repair facility that uses quality replacement parts. See “ Collision Parts ” earlier in this section.
Customer Information 12-13 In-Portfolio: Includes a Portfolio, Owner Manual, and Warranty Booklet. RET AIL SELL PRICE: $35.00 (U.S.) plus processing fee Without Portfolio: Owner Manual only .
12-14 Customer Information However , NHTSA cannot become involved in individual problems between you, your dealer , or General Motors. T o contact NHTSA, you may call the V ehicle Safety Hotline toll-free at 1-888-327-4236 (TTY : 1-800-424-9153); go to http://www .
Customer Information 12-15 V ehicle Data Recording and Privacy Y our GM vehicle has a number of sophisticated computers that record information about the vehicle ’ s performance and how it is driven.
12-16 Customer Information GM will not access this data or share it with others except: with the consent of the vehicle owner or , if the vehicle is leased, with the consent of the lessee; in response.
INDEX i-1 A Accessories and Modifications . . . . . . . . . . . . . . . . . . 9-3 Accessory Power . . . . . . . . . . . . . . 8-19 Adaptive Forward Lighting (AFL) . . . . . . . . . . . . . . . . . 5-4 Add-On Electrical Equipment . . . . . . . . . . . .
i-2 INDEX B Battery . . . . . . . . . . . . . . . . . . . . . . . . 9-29 Exterior Lighting Battery Saver . . . . . . . . . . . . . . . . . . . . . . . . 5-7 Jump Starting . . . . . . . . . . . . . . . 9-103 Load Management . . . . . . . . . . . . . 5-6 Power Protection .
INDEX i-3 Cleaning Exterior Care . . . . . . . . . . . . . . . .9-1 10 Interior Care . . . . . . . . . . . . . . . . .9-1 14 Climate Control Systems Dual Automatic . . . . . . . . . . . . . . . . 7-1 Clock . . . . . . . . . . . . . . . . . . . . . . .
i-4 INDEX Driving (cont.) Off-Road Recovery . . . . . . . . . . . . 8-6 V ehicle Load Limits . . . . . . . . . . . 8-12 Winter . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Dual Automatic Climate Control System . . . . . . . . . . . . . . . . 7-1 DVD/CD Player .
INDEX i-5 Front Seats Adjustment . . . . . . . . . . . . . . . . . . . . 2-3 Heated and V entilated . . . . . . . . . 2-9 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-49 Additives . . . . . . . . . . . . . . . . . . . . . 8-50 Economy Driving .
i-6 INDEX Heater Engine Coolant . . . . . . . . . . . . . . . 8-22 High-Beam On Light . . . . . . . . . . . 4-30 High-Speed Operation . . . . . . . . . 9-67 Highway Hypnosis . . . . . . . . . . . . . . 8-9 Hill and Mountain Roads . . . . . . . . 8-9 Hood .
INDEX i-7 Lights (cont.) Safety Belt Reminders . . . . . . . . 4-21 Security . . . . . . . . . . . . . . . . . . . . . . 4-30 T ire Pressure . . . . . . . . . . . . . . . . . 4-29 T raction Control System (TCS)/StabiliT rak ® . . . . . . . . . . 4-28 Up-Shift .
i-8 INDEX N Navigation System V ehicle Data Recording and Privacy . . . . . . . . . . . . . . . 12-16 Net Cargo . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Net, Convenience . . . . . . . . . . . . . . 3-6 New Vehicle Break-In . . . . . . .
INDEX i-9 R Radio Frequency Identification (RFID) . . . . . . . . 12-16 Statement . . . . . . . . . . . . . . . . . . 12-16 Radios AM-FM Radio . . . . . . . . . . . . . . . . . . 6-9 CD/DVD Player . . . . . . . . . . . . . . . 6-19 Reception . . . . .
i-10 INDEX Safety System Check . . . . . . . . . . 2-25 Satellite Radio . . . . . . . . . . . . . . . . . 6-1 1 Scheduled Maintenance . . . . . . . 10-3 Scheduling Appointments . . . . . . 12-8 Sealant Kit, Tire . . . . . . . . . . . . . . . 9-84 Seats Adjustment, Front .
INDEX i-1 1 T T achometer . . . . . . . . . . . . . . . . . . . . 4-17 T ext T elephone (TTY) Users . . . 12-4 Theft-Deterrent Systems . . . . . . . . . . . . . . . 1-24, 1-25 Immobilizer . . . . . . . . . . . . . . . . . . . 1-24 Thigh Support Adjustment .
i-12 INDEX U Ultrasonic Parking Assist . . . . . . 8-44 Uniform Tire Quality Grading . . . . . . . . . . . . . . . . . . . . . . 9-78 Universal Remote System . . . . . 4-61 Operation . . . . . . . . . . . . . . . . . . . . . 4-65 Programming . . . . .
An important point after buying a device Cadillac 2010 CTS-V (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Cadillac 2010 CTS-V yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Cadillac 2010 CTS-V - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Cadillac 2010 CTS-V you will learn all the available features of the product, as well as information on its operation. The information that you get Cadillac 2010 CTS-V will certainly help you make a decision on the purchase.
If you already are a holder of Cadillac 2010 CTS-V, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Cadillac 2010 CTS-V.
However, one of the most important roles played by the user manual is to help in solving problems with Cadillac 2010 CTS-V. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Cadillac 2010 CTS-V along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
