Instruction/ maintenance manual of the product TD-1100 Bush Hog
Go to page of 18
BU S H H O G ® OPERA TION ● MAINTENANCE $4.00 Operator ’s Manual T ri-Deck Finishing Mower TD - 1 1 00 1299 Part No. 50024754.
CONGRA TULA TIONS! Y ou have invested in the best implement of its type on the market today . The care you give your Bush Hog implement will greatly determine your satisfaction with its performance and its service life.
TD 1 100 F inishing Mower T ABLE OF CONTENTS SECTION/P ARA P AGE W arranty .................................................2 Dealer Preparation Check List ...............3 Safety Precautions .................................4 Federal Laws and Regulations .
BUSH HOG ® LIMITED W ARRANTY ✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯✯ Bush Hog warrants to the original purchaser of any new Bush Hog equipment, p.
DEALER PREP ARA TION CHECK LIST T ri-Deck Finishing Mower TD- 1 1 0 0 BEFORE DELIVERING MACHINE — The following check list should be completed. Use the Operator ’s Manual as a guide. ❒ 1. Assembly completed. ❒ 2. Gearboxes filled with oil. ❒ 3.
IMPORT ANT SAFETY PRECAUTIONS This symbol is used to call attention to safe- ty precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety precautions could result in serious bodily injury.
IMPORT ANT FEDERAL LA WS AND REGULA TIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERA TIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as such).
SECTION I INTRODUCTION AND DESCRIPTION 1-1 INTRODUCTION We are pleased to have you as a Bush Hog cus- tomer. Your TD-1100 Finishing Mower has been carefully designed to give maximum service with minimum down time.
2-1 A TT ACHING T O TRACTOR IMPORTANT (540 RPM only) The minimum required PTO horsepower is 30 H P for the TD-1100. A. Adjust tractor drawbar length to dimension shown in Figure 2-1. Incorrect drawbar length will change angle of driveline causing possible damage to constant velocity joint.
F. Route control chain to convenient location and fasten to tractor. Be sure excess slack is removed from the chain to avoid entanglement with tractor tires or other moving parts. Make sure latch locking pins are in the stored positions so that latches can be released by pulling the chain.
3-3 OPERA TION A. Perform BEFORE EACH USE maintenance list in paragraph 4-1. B. Standard Models With Single Acting Cylinders - Start tractor. Lower cutter decks until it is supported by caster wheels and place hydraulic valve in “float” position. Models Equipped With Double Acting Hydraulic Cylinder Conversion Kit - Start tractor.
SECTION IV MAINTENANCE 4-1 MAINTENANCE CHECK LIST Perform scheduled maintenance as outlined below. Lower implement to ground, turn off tractor, and set parking brake before doing maintenance inspections or work. All bolts should be torqued as indicated in torque chart unless otherwise indicated.
Figure 4-1 B (5) 30 Shots Before Each Use (1) 3 Shots Before Each Use (5) 10 Shots Before Each Use - (Access through holes in shields of telescoping driveline) (9) 40 Hrs (7) 40 Hrs (3) Before Each Us.
4-5 BLADE REPLACEMENT A. Raise cutter using tractor hydraulic system and use transport locks before changing blades. B. Turn off tractor,set parking brake and remove key. WEAR HEAVY WORK GLOVES TO PRO- TECT HANDS FROM SHARP EDGES. WHEN TURNING BLADES, BE AWARE OF OPPOSITE BLADE APPROACHING.
SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge.
DECALS CONTINUED 82683 83105 14.
T ORQUE SPECIFICA TIONS Proper toque for American fasteners used on Bush Hog equipment. Recommended Torque in Foot Pounds (Newton Meters).* BOLT DIAMETER WRENCH (IN.
P .O. Box 1039 ● Selma, AL 36702-1039 T elephone (334) 874-2700 BUSH HOG ®.
An important point after buying a device Bush Hog TD-1100 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bush Hog TD-1100 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bush Hog TD-1100 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bush Hog TD-1100 you will learn all the available features of the product, as well as information on its operation. The information that you get Bush Hog TD-1100 will certainly help you make a decision on the purchase.
If you already are a holder of Bush Hog TD-1100, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bush Hog TD-1100.
However, one of the most important roles played by the user manual is to help in solving problems with Bush Hog TD-1100. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bush Hog TD-1100 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
