Instruction/ maintenance manual of the product Ultra 2 Bunn
Go to page of 14
UL TRA-1 UL TRA-2 INST ALLA TION & OPERA TING GUIDE BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX: (217) 529-6644 T o ensure you have .
2 40563 041108 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor . 2) Electronic circuit and/or control boards: parts and labor for 3 years.
3 INTRODUCTION This equipment dispenses granita-type and cold liquid drinks on demand from separate hoppers. Operating controls are accessible only through password protection. CONTENTS Introduction & Warranty .....................................
4 INITIAL SETUP CAUTION – The dispenser is ver y heavy! Use care when lifting or moving it. Use at least two people to lift or move the dispenser . 3. Remove the rear plastic plug from the trim strip between the ho pp er dr ip tr ay s an d loo sen th e auger motor cover screws.
5 11. Thoroughly rinse the hoppers an d ins tal l th em over the auge rs and cooling drums. 15. Set the lid(s) on the hopper(s). Lift slightly and slide back or front for filling. 16. Plug in the hopper lid lamp cord(s). 17. Assemble the drip tray . INITIAL SETUP (CONT .
6 P3678 Set Consistency This function allows the operator to adjust the ice consistency , or torque of each auger when answered YES (“ICE”). T wo screens will appear for left and right. The operator can scroll through a range of a minimum of 1 (UL TRA) to a maximum of 16 (ICE).
7 Set Time and Date Selecting YES (ICE) allows the operator to set the DA TE (YY MM DD) and TIME (HR MIN SEC) for display on the Home Screen. SET DA TE TIME ? NO Y E S YEAR 2005 (-) NEXT (+) MONTH 1 (.
8 OPERA TING CONTROLS UL TRA-1 There are three of these switches that will be used for the operation of the dispenser . 1. switch (upper left corner of the control pad) This switch is the ON/OFF toggle switch which powers up the dispenser and the LCD display .
9 OPERA TING CONTROLS UL TRA-2 There are five of these switches that will be used for the operation of the dispenser . 1. switch (upper left corner of the control pad) This switch is the ON/OFF toggle switch which powers up the dispenser and the LCD display .
10 USING THE DISPENSER FOR GRANIT A-TYPE PRODUCTS 1. Lift the lid slightly for the selected hopper and slide back to gain access to the hopper . 2. Place the pre-mixed liquid product in the selected hopper . 3. a. Press and release the (ON/OFF) switch to power on the dispenser .
11 OTHER RECOMMENDA TIONS FOR YOUR DISPENSER • Whetherliquidconcentrateorgranulatedpowder ,allproductmustbethoroughlymixedBEFOREaddingit to the hoppers. • Forbestresultswithgranita-typeproducts,useonlyproductswithan apparentbrixof12orhigher .
12 10. Place all parts in a clean sink with mild hot water (120°F) and sanitizer solution. Allow all parts to soak for at least 5 minutes. Carefully wash all components with a clean wash cloth in the hot water and sanitizer solu- tion. Use a clean, soft bristle brush as needed for the smaller components and tight areas.
13 1. Install the seal(s) over the flange at the rear of the cooling drum(s) and press the seal(s) firmly into place as shown. 2. Ali gn the auge r sha ft( s) with the auger(s). Push the auger(s) as far as they will go and rotate so the flat face of the auger shaft is aligned with the flat face of the auger nose.
14 USER NOTICES Carefully read and follow all notices on the equipment and in this manual. They were written for your protec- tion. All notices are to be kept in good condition. Replace any unreadable or damaged labels. 27442.0000 32162.0000 (UL TRA-2) 00986.
An important point after buying a device Bunn Ultra 2 (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bunn Ultra 2 yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bunn Ultra 2 - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bunn Ultra 2 you will learn all the available features of the product, as well as information on its operation. The information that you get Bunn Ultra 2 will certainly help you make a decision on the purchase.
If you already are a holder of Bunn Ultra 2, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bunn Ultra 2.
However, one of the most important roles played by the user manual is to help in solving problems with Bunn Ultra 2. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bunn Ultra 2 along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
