Instruction/ maintenance manual of the product TB3 Series Bunn
Go to page of 11
TB3 Series Including: TB3; TB3-LP; TB3Q; TB3Q-LP ST ARTING WITH SERIAL NUMBER: TU000200000 INST ALLA TION & OPERA TING MANUAL BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS .
Page 2 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) All equipment other than as specified below: 2 years parts and 1 year labor . 2) Electronic circuit and/or control boards: parts and labor for 3 years.
Page 3 W ARNING ! Fill water tank before turning - on - thermostat or connecting appliance to power sour ce. Use only on a pr operly pr otected circuit capab le of the rated load. Electrically gr ound the chassis. Follow national/local electrical codes.
Page 4 ELECTRICAL REQUIREMENTS CAUTION - The brewer must be disconnected from the power source until specified in Initial Set-Up. 120V model brewers require 2-wire, grounded service rated 120 volts ac, 15 amp, single phase, 60 Hz. "A" model brewers require 2-wire, grounded service rated 230 volts ac, 10 amp, single phase, 50 Hz.
Page 5 120V MODELS These brewers must be connected to a cold water system with operating pressure between 20 and 90 psi (138 and 620 kPa) from a ½˝ or larger supply line.
Page 6 o o o o ADJUSTING BREW VOLUMES NOTE: Check that the brewer is connected to water supply , the tank is properly filled, and a funnel and server are in place, prior to setting or modifying batch sizes.
Page 7 INITIAL SET -UP (TB3Q/TB3Q-LP ONL Y) CAUTION - The brewer must be disconnected from the power source throughout the Initial Set-Up, except when specified in the instructions. 1. Remove the top lid from the brewer . 2. Rotate the control thermostat knob fully counterclockwise to the "OFF" position and replace the top lid.
Page 8 INITIAL SET -UP (TB3/TB3-LP ONL Y) CAUTION - The brewer must be disconnected from the power sour ce throughout the initial set-up, except when specified in the instructions. 1. Remove the top lid from the brewer . 2. Rotate the control thermostat knob fully counterclockwise to the "OFF" position and replace the top lid.
Page 9 AUTO SWEETENER SET -UP CAUTION - The brewer must be disconnected from the power source throughout the Initial Set-Up, except when specified in the instructions. 1. Remove the top lid and both rear panels. 2. Make sure the brewer water supply is off.
Page 10 41465 082208 OPERA TING CONTROLS A. ON/OFF Switch ON - Placing the switch in the left position allows the start switch to activate a timed brew cycle for three gallons of tea. OFF - Placing the switch in the right position stops the brew cycle.
Page 11 41465 082208 CLEANING CAUTION - CLEAN AND SANITIZE YOUR ICED TEA BREWER DAIL Y 1. Remove and thoroughly clean the entire brew funnel. The funnel tip and screen must be free from any tea particles or residue. Reassemble the funnel. 2. Place the ON/OFF switch in the "OFF" position.
An important point after buying a device Bunn TB3 Series (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bunn TB3 Series yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bunn TB3 Series - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bunn TB3 Series you will learn all the available features of the product, as well as information on its operation. The information that you get Bunn TB3 Series will certainly help you make a decision on the purchase.
If you already are a holder of Bunn TB3 Series, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bunn TB3 Series.
However, one of the most important roles played by the user manual is to help in solving problems with Bunn TB3 Series. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bunn TB3 Series along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
