Instruction/ maintenance manual of the product IMIX -3S+A Bunn
Go to page of 13
IMIX ® -3S+ IMIX ® -3S+A IMIX ® -5S+ IMIX ® -5S+A INST ALLA TION & OPERA TING GUIDE BUNN-O-MA TIC CORPORA TION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 F AX:.
2 38987 080112 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal ser vers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor .
3 WA RNING ! Fill water tank before turning - on - thermostat or connecting appliance to power source. Use only on a properly protected circuit capable of the rated load. Electrically ground the chassis. Follow national/local electrical codes. Do not use near combustibles.
4 ELECTRICAL REQUIREMENTS CAUTION - The dispenser must be disconnected from the power source until specified in Electrical Hook-Up. The 120 volt version of this dispenser has an attached cordset. The mating connector must be a NEMA 5-15R. T o access terminal block for high voltage models without a cordset, remove left side panel.
5 38987 120513 PLUMBING REQUIREMENTS This dispenser must be connected to a cold water system with operating pressure between 20 and 90 psi (138 - 620 kPa) from a 1⁄2” or larger supply line. A shut-off valve should be installed in the line before the dispenser .
6 38987 120513 RUNNING A RINSE SEQUENCE 1. Place the Normal/Program/Rinse switch (page 9) in the “rinse” position. 2. Sequentially at each position, press all of the dispense switches. The dispenser will run for 10 seconds with the hopper(s) disabled.
7 CLEANING The use of a damp cloth rinsed in any mild, non-abrasive, liquid detergent is recommended for cleaning all sur - faces on Bunn-O-Matic equipment.
8 Adjust tank temperature (190° F maximum) Adjust minimum tank ready temper - ature for lockout (185° maximum) Adjust hopper motor speed for station selected T ANK TEMP XXX° (-) EXIT (+) READY TEMP.
9 D igital B everag e C ontr ol D igital B everage C ontr ol ST OP PROGRAM HOME SCREEN The screen above will be shown when the dispenser is ready for use. While the tank is heating, the water temperature will be displayed until the ready temperature is reached .
10 PROGRAMMING CUP SIZES - Portion Control Models The cup size can be programmed in portion control models by “EXAMPLE” or “TIME”. Programming by EX- AMPLE is manually pressing desired dispense button, then releasing when the desired cup size is attained.
11 PORTION CONTROL ? NO EXIT YES Press and release right switch (advance to next menu), “T ANK TEMP XXX°” appears on screen. PROGRAMMING THE DISPENSER (cont.
12 XX° CAL XX° (-) T ank T emp (+) PROGRAMMING THE DISPENSER (cont.) DRINK STRENGTH 1 (-) XX (+) PRESS DISPENSE TO CHECK T ASTE T ASTE 1 OK ? NO YES (B) Adjust hopper motor speed for station selected SELECT UNITS ENG EXIT METRIC (D) 235 REFILL 155 (-) EXIT (+) Auger Delay (-) .
13 PROGRAMMING THE DISPENSER (cont.) RINSE ALARM ? NO EXIT YES HEAD 1 DISABLE ? NO EXIT YES SET P ASSWORD ? (-) XXXX (+) Returns to (G) (page 11) TEST SWITCHES ? Use Switch T o T est TEST HEA TER ? EX.
An important point after buying a device Bunn IMIX -3S+A (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bunn IMIX -3S+A yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bunn IMIX -3S+A - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bunn IMIX -3S+A you will learn all the available features of the product, as well as information on its operation. The information that you get Bunn IMIX -3S+A will certainly help you make a decision on the purchase.
If you already are a holder of Bunn IMIX -3S+A, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bunn IMIX -3S+A.
However, one of the most important roles played by the user manual is to help in solving problems with Bunn IMIX -3S+A. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bunn IMIX -3S+A along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
