Instruction/ maintenance manual of the product IC3B Bunn
Go to page of 9
IC3 & IC3B ON HALF OFF FULL START READY ON HALF OFF FULL START READY INST ALLA TION & OPERA TING GUIDE BUNN-O-MA TIC CORPORA TION POST OFFICE BO X 3227 SPRINGFIELD , ILLINOIS 62708-3227 PHONE:.
Page 2 10792 080112 BUNN-O-MA TIC COMMERCIAL PRODUCT WARRANTY Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows: 1) Airpots, thermal carafes, decanters, GPR servers, iced tea/coffee dispensers, MCP/MCA pod brewers thermal ser vers and Thermofresh servers (mechanical and digital)- 1 year parts and 1 year labor .
Page 3 INTRODUCTION This equipment will brew a batch of fresh coffee into an awaiting vessel and dispense at approximately room tempera- ture to conserve ice. The brewer is only for indoor use on a sturdy counter or shelf and requires a minimum of 33 inches of clearance above the counter .
Page 4 Electrical Hook-Up CAUTION – Improper electrical installation will damage electronic components. 1. An electrician must provide electrical service as specified. 2. Remove the top lid and rotate the control thermostat knob fully counter clockwise to the “OFF” position and reinstall the top lid.
Page 5 PLUMBING REQUIREMENTS This brewer must be connected to a cold water system with operating pressure between 30 (207 kPa) and 90 psi (620 kPa) from a 1 ⁄ 2 " or larger supply line. A shut-off valve should be installed in the line before the brewer .
Page 6 10792 050405 INITIAL SET -UP 1. Remove the top lid from the brewer . 2. Rotate the control thermostat knob fully counterclockwise to the “OFF” position and replace the top lid. 3. Insert an empty funnel into the funnel rails. 4. Place an empty dispenser on the brewer base.
Page 7 ADJUSTING BREW VOLUMES CAUTION - Disconnect the power source from the brewer prior to the removal of any panel for the replacement or adjustment of any component. NOTE: Prior to setting or modifying batch sizes, check that the brewer is connected to water supply , the tank is properly filled, and a funnel and server are in place.
Page 8 10792 072408 OPERA TING CONTROLS A. Lighted On/Off Switch ON - Placing the switch in the lighted upper position allows the start switch to activate a brew cycle.
Page 9 FULL/HALF SW 4 2 READY INDICA TOR SW . & THERMOS TAT SCHEMA TIC WIRING DIAGRAM IC3 BLK BLK GRN TA NK HEA TER RED 10793.0000B 01/07 ©1994 BUNN-O-MA TIC CORPORA TION 120/208 VOL TS AC OR 120.
An important point after buying a device Bunn IC3B (or even before the purchase) is to read its user manual. We should do this for several simple reasons:
If you have not bought Bunn IC3B yet, this is a good time to familiarize yourself with the basic data on the product. First of all view first pages of the manual, you can find above. You should find there the most important technical data Bunn IC3B - thus you can check whether the hardware meets your expectations. When delving into next pages of the user manual, Bunn IC3B you will learn all the available features of the product, as well as information on its operation. The information that you get Bunn IC3B will certainly help you make a decision on the purchase.
If you already are a holder of Bunn IC3B, but have not read the manual yet, you should do it for the reasons described above. You will learn then if you properly used the available features, and whether you have not made any mistakes, which can shorten the lifetime Bunn IC3B.
However, one of the most important roles played by the user manual is to help in solving problems with Bunn IC3B. Almost always you will find there Troubleshooting, which are the most frequently occurring failures and malfunctions of the device Bunn IC3B along with tips on how to solve them. Even if you fail to solve the problem, the manual will show you a further procedure – contact to the customer service center or the nearest service center
